Question about 1991 Ford Ranger Supercab

Open Question

I need a fuse box diagram for a 1991 ford ranger

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
PyroPCMan
  • 405 Answers

SOURCE: 1991 Ford Ranger manual transmission remove

444a343.jpg

  1. Disconnect the negative battery cable.
  2. Remove the gearshift lever assembly from the control housing.
  3. Cover the opening in the control housing with a cloth to prevent dirt from falling into the unit.
  4. Raise the vehicle and support it safely.
  5. On 2WD vehicles, matchmark the driveshaft to the rear axle flange. Position a drain pan under the tailend of the transmission. Remove the driveshaft-to-rear axle flange fasteners and pull the driveshaft rearward to disconnect it from the transmission.
  6. Disconnect the clutch hydraulic line a the clutch housing. Plug the lines.
  7. Disconnect the speedometer from the transfer case/extension housing.
  8. Disconnect the starter motor, back-up lamp and, if equipped, neutral sensing switch harness connector.
  9. Place a wood block on a service jack and position the jack under the engine oil pan.
  10. On 4WD vehicles, remove the transfer case from the vehicle.
  11. Remove the starter motor.
  12. Position a transmission jack, under the transmission.
  13. Remove the transmission-to-engine retaining bolts and washers.
  14. Remove the nuts and bolts attaching the transmission mount and damper to the crossmember.
  15. Remove the nuts and bolts attaching the crossmember to the frame side rails and remove the crossmember.
  16. Lower the engine jack slightly to angle the transmission assembly. Work the clutch housing off the locating dowels and slide the clutch housing and the transmission rearward until the input shaft clears the clutch disc.
  17. Lower the transmission jack and remove the transmission from the vehicle.
To install:
  1. Check that the mating surfaces of the clutch housing, engine rear and dowel holes are free of burrs, dirt and paint.
  2. Place the transmission on the transmission jack. Position the transmission under the vehicle, then raise it into position. Align the input shaft splines with the clutch disc splines and work the transmission forward into the locating dowels.
  3. Install the transmission-to-engine retaining bolts and washers. Tighten the retaining bolts to specifications. Remove the transmission jack.
  4. Install the starter motor. Tighten the attaching nuts.
  5. Raise the engine and install the rear crossmember, insulator and damper and attaching nuts and bolts. Tighten and torque the bolts to specification.
  6. On 4WD vehicles, install the transfer case.
  7. On 2WD vehicles, insert the driveshaft into the transmission extension housing and install the center bearing attaching nuts, washers and lockwashers. Connect the driveshaft to the rear axle drive flange.
  8. Connect the starter motor, back-up lamp and, if equipped, neutral sensing switch connectors.
  9. Connect the hydraulic clutch line and bleed the system.
  10. Install the speedometer cable.
  11. Check and adjust the fluid level.
  12. Lower the vehicle.
  13. Install the gearshift lever assembly. Install the boot cover and bolts.
  14. Reconnect the negative battery cable.
  15. Check for proper shifting and operation of the transmission.
The above was pulled frrom:
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800391da

hope this helps

Posted on Jul 02, 2008

Ad
  • 1 Answer

SOURCE: need to know flash relay position in fuse box diagram helpful

i need the 2003 ranger fuse box diagram can i get it for free? and where

Posted on Sep 17, 2008

  • 82 Answers

SOURCE: 1991 civic fuse box diagram

1992 civic but this is probably the same as yours. http://autoforums.carjunky.com/autof...A_CIVIC_P3020/

Posted on Oct 10, 2008

michigan man
  • 3533 Answers

SOURCE: i need the fuse box

the diagrams are under the lid of the fuse box located under the dash on driverside and on the top of the relay box located under the hood on driverside

Posted on Apr 26, 2009

kamakani
  • 104 Answers

SOURCE: need to know what fuse goes where

I am not sure if this right and there should be diagram on the back of cover.


1 5A Power Mirror Switch

2 10A Daytime Running Lights (DRL),
Back-up Lamps, Transmission,
Passenger Air Bag Deactivation
Switch, Blower Motor Relay

3 7.5A Right Stop/Turn Trailer Tow
Connector

4 — Not Used

5 15A 4x4 Control Module

6 — Not Used

7 7.5A Left Stop/Turn Trailer Tow
Connector

8 — Not Used

9 7.5A Brake Pedal Position Switch

10 7.5A Speed Control Servo/Amplifier
Assembly, Generic Electronic
Module (GEM), Shift Lock
Actuator, Turn Signals

11 7.5A Instrument Cluster, 4x4, Main
Light Switch, Truck Central
Security Module (TCSM)

12 — Not Used

13 20A Brake Pedal Position Switch

14 10A or Not Used 10A: If equipped with Anti-Lock
Brake System (ABS) Control
Module

15 — Not Used

16 30A Windshield Wiper Motor, Wiper
Hi-Lo Relay, Wiper Run/Park
Relay

17 20A Cigar Lighter, Data Link
Connector (DLC)

18 — Not Used

19 25A PCM Power Diode, Ignition, PATS

20 7.5A Generic Electronic Module
(GEM), Radio

21 15A Flasher (Hazard)

22 20A Auxiliary Power Socket

23 — Not Used

24 7.5A Clutch Pedal Position (CPP)
switch, Starter Interrupt Relay

25 — Not Used

26 10A Battery Saver Relay, Auxillary
Relay Box, Restraint Central
Module (RCM), Generic Electroic
Module (GEM), Instrument
Cluster

27 — Not Used

28 7.5A Generic Electronic Module
(GEM), Radio

29 20A Radio

30 — Not Used

31 — Not Used

32 — Not Used

33 15A Headlamps, Daytime Running
Lamps (DRL) Module, Instrument
Cluster

34 — Not Used

35 15A or Not Used 15A: Horn Relay if Not Equipped
with Truck Central Security
Module

36 — Not Used

Posted on Jun 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Inside lights what fuse runs it


Keith, 1995 ford ranger, looks like interior light fuse is # 27, 10 amp. in interior fuse box panel and module #3 in under hood fuse/relay. Pg. 308 to 315 in the attached manual show fuse locations for all. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Ford Ranger 1996 2007 fuse box diagram USA version Auto Genius
Diagram of 1996 ford ranger fusebox which fuse is
Ford Ranger Owner Manual
1995 ford ranger xlt interior light fuse location Google Search

Aug 21, 2016 | Ford Cars & Trucks

1 Answer

2000 ford ranger 3.0 fuse box diagram


here is a web site, hope this is what you are looking for! it 's the same from 1996-2007!

http://www.autogenius.info/ford-ranger-1996-fuse-box-diagram-usa-version/

Jun 29, 2016 | 2000 Ford Ranger SuperCab

1 Answer

Fuse diagram 2004 ford ranger 2.3


Kim, Check the attached links,instruction and guides for your Ford diagram. Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Ford Ranger 1996 fuse box diagram USA version Auto Genius

Repair Guides Circuit Protection 2004 Fuse Relay Information AutoZone com

Ranger Fuse Layout Ford Truck Enthusiasts Forums

Apr 21, 2016 | Ford Cars & Trucks

1 Answer

Diagram of 1996 ford ranger fusebox which fuse is


Here is a diagram of 1996 Ford Ranger fuse box25297289-e4nsevljl1gt44onigrs2by0-5-0.gif

Nov 25, 2014 | 1992 Ford Ranger

1 Answer

Fuse panel diagram for 2001 ford ranger fuse box


On this website, you find fuse box diagram and description for Ford Ranger (2001)

Ford Ranger 2001 2002 fuse box diagram Auto Genius

Oct 20, 2012 | 2001 Ford Ranger Regular Cab

1 Answer

Fuse box diagram of a 2001 ford ranger, types of fuses


On this website, you find fuse box diagram and description for Ford Ranger (2001 - 2002)


Ford Ranger 2001 2002 fuse box diagram Auto Genius

Jul 21, 2011 | Ford Ranger Cars & Trucks

1 Answer

I need a fuse box diagram


Go to this FREE Ford website to view or download the vehicles owners manual.
The fuse block diagram is located in the roadside emergency section.
www.fleet.ford.com/maintenance/owners_manuals/default.asp

Nov 11, 2010 | 1991 Ford Ranger Supercab

1 Answer

Need to know flash relay position in fuse box diagram helpful


i need the 2003 ranger fuse box diagram can i get it for free? and where

Aug 04, 2008 | 2003 Ford Ranger Regular Cab

Not finding what you are looking for?
1991 Ford Ranger Supercab Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...