How do u set the timing on 4cly, 1991, 2wd, 2.4,,, ??? Mighty max

Mitsubishi Mighty Max Parts & Accessories - JCWhitney

www.jcwhitney.com > Mitsubishi

Below you'll find a wide variety of Mitsubishi Mighty Max parts and accessories. Enter the year of your Mitsubishi Mighty Max to get a more customized product ...

Mitsubishi Mighty Max Cars and Parts ' eBay

www.ebay.com > eBay Motors > Cars & Trucks > Mitsubishi

eBayResearch Mitsubishi Mighty Max popular models, prices, photos and read reviews. ...Tell us what you thinkthis item - opens in a new window or tab. Mitsubishi Mighty Max. Share: Mitsubishi Mighty Max Model Years ... Mitsubishi Mighty Max · 1990 Mitsubishi Mighty Max · 1989 Mitsubishi Mighty Max · 1988 Mitsubishi Mighty ...

Mitsubishi Mighty MAX Parts, Mitsubishi Mighty MAX ...

www.carparts.com > Mitsubishi

Through the years, your vehicle's components will succumb to wear and tear, ... In addition to replacement Mitsubishi Mighty Max parts, you may also want to buy ...

Mitsubishi Mighty Max crankshaft bolt Questions & Answers ...

www.fixya.com > ... > crankshaft bolt > Cars & Trucks > Mitsubishi

Mitsubishi Mighty Max cars & trucks crankshaft bolt questions and answers. ...Torque specs for mighty max The head torque specs for 1991 mitsubishi mighty max 2.4 I ... 1989 mitsubishi 2.0 motor crankshaft was turned while timeing belt was off. ...how to install a clutch kit on my 1994 mitsubishi mighty max Disconnect the .

I recommend changing out your transmission fluid, make sure you replace the screen too. After a vehicle have set for a long period of time it s good to flush all the fluids if you did replace them prior to the vehicle being stored.

Hello bojak80,

The basic timing is 5 deg. BTDC. Below is a picture of the timing mark. I hope this helps you.



Regards,
netvan

ON 4-CYL: 1-3-4-2. ON V-6: NO DIST,: 1-2-3-4-5-6. WITH DISTRIBUTOR: 1-2-3-4-5-6 COUNTERCLOCKWISE

1990 Mitsubishi Truck Mighty Max 2WD 2.4L FI 4cyl
The Firing Order mitsutrk01:
Firing order 1-3-4-2 --------- front | | of | 1 2 3 4 | Distributor rotates clockwise vehicle | | ---------

1990 Mitsubishi Truck Mighty Max 4WD 3.0L FI 6cyl
The Firing Order mitsutrk04:
Firing order 1-2-3-4-5-6 ------- front | 1 3 5 | of | | distributor rotates counter vehicle | 2 4 6 | clockwise -------


Hope help with this (remember rated this help).

Next time when cold and it will not start remove a spark plug or two and see if the engines flooded. If so there are two things that come to mind; 1, worn injectors, leaking as engine sits with time causing difficult starts 2: bad oxygen sensor, if failed engines tend to run rich and the ECU may have your injectors pump heavy amounts of fuel to keep from running lean; often times you'll see poor fuel MPG if O2 sensor failed.

I hope this may have assisted you,
Tom

Per my Chilton's manual tehe bolts should be (cold engine) 65 to 72 FT. Pnds., the cam shaft bearing bolts should be 8x25 = 15 - 19 Ft pnds and the 8x65 should be 14 - 15 Ft Pnds.

The sequence is as follows for the (10 ) head bolts:

7 - 5 - 2 - 4 - 10

9 - 3 - 1 - 6 - 8

I hope this may help,
Tom

timing chain when you get a variance in timing easy to see with a timing light haynes manual should be sufficient