Question about 1993 Oldsmobile Cutlass Ciera

1 Answer

1993 Cutlass Ciera Install Ball Joints

Is this a tough job?

Posted by on

  • Macky33 Jul 08, 2008

    My husband wants to do it himself.

    Replacing the ball joints.

    How tough of a job is it????
    Any feedback would be great.

    Thanks

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,114 Answers

Well has he ever replaced Ball joints before if not it would be ideal for someone to assist you first time!a great effort and knowledge required!!each to his own hope this helps.

Posted on Dec 23, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car 1993


On the starter.....cant miss them they will be latched on to tge side of the engine. Especially in that car. It might be a little tough u might have to remove some pumps

May 03, 2013 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Front end


Check ball joints or tierods

Mar 06, 2013 | 1994 Oldsmobile Cutlass Ciera

1 Answer

WIRING DIAGRAM FOR 1993 CUTLASS CIERA s


how change the starter for cutlass cierra s

May 26, 2012 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Where are the grease zerks located on a 1996 Old Ciera S.L.?


they are located on the bottom center of the ball joints and the bottom center of the outer tie rod ends below the joint.at the rear of the suspension in the same location on the ball joints if this set up has rear ball joints.if you don`t see them it may have joints that are what they call permanetly sealed joints and don`t need grease.they should be checked for being worn out.

Jun 08, 2011 | 1996 Oldsmobile Cutlass Ciera

1 Answer

1993 old cutlass ciera failed inspection for HC. car was tuned up hc dropped but not low enough


Install Full Synthetic Oil
New Exhaust Converter
New O2 Sensor
New Air Filter

Mar 21, 2011 | 1993 Oldsmobile Cutlass Ciera

1 Answer

How to change a thermostat in a 1993 oldsmobile cutlass ciera


Drain some coolant from radiator to below level of thermostat housing. Be careful to keep pets away as coolant is very sweet smelling and poison. Remove two bolts holding thermostat housing in place and use catch pan to catch fluid. Clean all gasket material from both sides of housing. Clean threads of bolts and use gasket shellac on them and new gasket. Install thermostat same as old one was, install new gasket, tighten bolts to correct torque value as found in your handy dandy shop manual. Refill radiator and check for leaks.

Aug 04, 2010 | 1993 Oldsmobile Cutlass Ciera

1 Answer

Engine locks up and stalls when coming to a stop. To clear it up I have to put the transmission in reverse and ref the engine while holding the brakes. 1994 olds cutlass ciera.


this sounds like the transmission torque converter clutch is not releasing, it causes this exact symptom. Have a local trans shop test drive it, in these tough times they will do that for free hoping to get the repair job.

May 03, 2009 | 1994 Oldsmobile Cutlass Ciera

1 Answer

How to change a starter in a 1992 oldsmobile cutlass ciera


disconnect battery,three bolts hold it to bell housing and two wires ,one is the feed the other activates the solonoid Easy job to do but dirty dirt grease and muck

Jan 24, 2009 | 1993 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1993 Oldsmobile Cutlass Ciera Logo

Related Topics:

136 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

70346 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6864 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...