Question about 1985 Ford Bronco

1 Answer

I own a 1971 ford bronco with a 351w and a truck four speed.My problem is that,when i push in the clutch pedal and try to start it my bronco moves forward like it won't disengage itself what do i do

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 223 Answers

Your clutch is dragging, that is, it's not 'throwing out'. If you have a hydraulic clutch check the fluid in the reservoir, If mechanical, just look for the point where you adjust it and tighten it up a little- I don't remember which those old Broncos had.

Ensure that it's not frozen before you adjust it though- frozen clutch has to be warmed up and then driven a little to dry it

If adjusting it get you no satisfaction then observe what you can and report back- the list of possible causes is long.

lp

Posted on Jan 01, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Ford courier1995 Ford Courier clutch will not disengage... clutch pedal easily floored with no ability to engage first gear.


the automatic clutch adjuster mechanism at the top of the pedal inside the cab is my first suspect before the clutch itself

May 03, 2011 | 1995 Ford Bronco

1 Answer

Need directions to bleed slave cylinder on '89 bronco 2 4x4


brakes or clutch??,if clutch get assistant to work pedal ,pump a few times then hold down ,you push the clutch arm in with a bar and open the bleed nipple at the same time then close the nipple and repeat ,after about 3/4 goes it should have pressure

Dec 22, 2009 | 1989 Ford Bronco II

1 Answer

I have a 1994 ford bronco with a 5.8 351w. when ignition is turned to accessories the fuel pump will come on for 2-3 sweconds then go off,but after a few minutes it will come on and stay on. when the...


Take your Bronco to an Autozone or Oreillys for a free scan. Offhand a new ignition switch would seem like a good idea, because the fuelpump should not be working in the ACC position.
If a new ignition switch does not help the fuelpump problem the pump is wired to an accessory. You need to look up the fuse info in an owners manual.

Dec 01, 2009 | 1989 Ford F 150

1 Answer

Clutch ignition switch 89 ford bronco, cant find it


The clutch switch should be somewhere at the clutch pedal upper side.

Nov 07, 2009 | 1989 Ford Bronco

1 Answer

89 ford bronco tranny problems


when you try to put it in gear engine off,does it roll either way when you push it?it could be a broken chain in the transfer case,or input shaft in the transfer case

May 18, 2009 | 1989 Ford F 150

1 Answer

My Bronco is stuck in reverse


Make sure your emergency brake cable hasn't seized up. Some vehicles use reverse to adjust the brakes. Try moving the vehicle with the clutch pushed in, then with the clutch out to make sure it is not sticking, check your shifter linkage to make sure it is not bent or sticking.

May 09, 2009 | 1986 Ford Bronco II

1 Answer

1986 bronco II no clutch


Where is the fluid coming out? Sounds like a loose hose/line or bad clutch master

Jan 25, 2009 | 1988 Ford Bronco II

3 Answers

87 ford bronco


I had a similar issue with my 88 XLT w/351w. It was the beginning of a problem with my MAPP sensor. After a wjile I could hardly keep the truck running at all. I changed the MAPP sensor and made sure the timing was still on and now it runs fine.

Aug 26, 2008 | 1995 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

132 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...