Question about 2002 Dodge Grand Caravan

1 Answer

2006 ram1500 my left headlight will not work on low, high beams and driving lights are fine

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 63 Answers

If your vehicle is 4 years old, I would suggest replacing both left and right headlght bulbs. It appears that your low beam filiment in your left light bulb is blown. I am assuming the wiring to the light socket is OK. Your local auto parts store can help you with this and sell you the correct bulb type for your vehicle. The bulbs are accessable behind the light assembly. The socket the bulb sits in can be removed from the rear of the light housing by turning it counter clockwise and pulling out. Replace the bulb. Don't touch the new bulb glass with your hands, but use a clean towel as not to get any oil on the glass. Rinstall bulb into socket and place the socket back on the light housing and turn it until it locks. Hopfully your truck is friendly and you can reach behind the light assembly easy.

Hope this helps.

Posted on Jan 01, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

While low beams on the left high beams stays on dim light but wen I turn high beams on they work fine


It could be driving lights mode instead of low beam. Check connections.

Jun 16, 2017 | Cars & Trucks

1 Answer

High beams work for both lights, 1 low beam does not


Check for power with a test light with the light connected. If you have power then its the ground. If no power then you will need to trace the wire back to find break. As I recall they did have seperate fuse for left and right headlight high & low beam. Also did you get a defective new bulb?

May 31, 2015 | 2006 Mazda Tribute

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

2 Answers

Dodge ram 3500 turn signal - headlight problem


WAY TO GO !!! another "great idea" from vehicle manufactures

Jun 07, 2012 | 2004 Dodge Ram 3500 Truck

1 Answer

2006 RAM1500 left headlight won't work, new bulb, new pigtail and still no power to the low beam wire. Tried testing the headlight switch, but can only find 12v in, must be low voltage output. Am I...


Yes, the control system is low power. In theory, this increases reliability and durability in the switch. The likely problem is the power module low beam driver.

jturcotte_2302.gif
jturcotte_2303.gif

jturcotte_2304.gif

Sep 19, 2011 | 2002 Dodge Grand Caravan

1 Answer

I recently puchased blueish headlight bulbs for my 2006 Volvo S80. The original bulbs were 55W for both the low and high beams. i replaced the high beams with 100w blueish bulbs and they work fine. When...


i think im right in saying the low beam bulbs are twin filament(low and high beam in one)and the main/high beam are single filament(spotlights).

Aug 17, 2010 | 2006 Volvo S60

2 Answers

One high beam works one doesn't, gauge cluster does not light up


you say you replaced both bulbs, you mean right and left or both the high beam and the low beam on left side?could be a bad ground for the left headlight. there should be some ground wires there near the headlight, LF corner under hood. without a wiring diagram here at home,I am not much help.

Sep 26, 2009 | 2000 Honda Accord

3 Answers

High-low beams not working


Check for headlight relay and fuse. Some cars have separate circuits for head light flasher and normal high/low beam. From your description, I would suspect a bad connection to/from relay or relay itself.

Jul 07, 2009 | 2006 Hyundai Accent

Not finding what you are looking for?
2002 Dodge Grand Caravan Logo

198 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...