Question about 2004 Chevrolet Astro

Open Question

P0300 = Randon/Multiple Cylinder Misfire Detected P0141= 02 Sensor Heter Circuit Malfuntion (Bank 1 Sensor 2)

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
roedmondson
  • 68 Answers

SOURCE: 2000 CIVIC System too lean Cylinder 3 and 4 misfire Deteced

  1. P0171: This means that the oxygen sensor has detected a lean air-fuel ratio. This can be caused due to a vaccuum leak or a problem in the HO2S circuit or the HO2S (Heated Oxygen Sensor) itself. (Bank one Sensor one). This is commonly located along the exhaust pipe. It could also be a bad Mass Air Flow sensor or a bad Engine Coolant Temperature sensor. Diagnostic checks will be needed to be carried out to be verified though
  2. Well as for the other codes, it means #3&4 cylinders are misfiring. It is a possibility that the P0171 code mite have caused the others to show up. I can be wrong though. But it is a strong possibility. If the air fuel mixtue is too lean indeed, mis-firing will occur, unless it is an actual electronic and not a mechnical problem. By the way, when these codes appear, how is the engine's performance. Does it remain the same or behaves poorly?

Posted on Feb 14, 2009

Ad
  • 107 Answers

SOURCE: the computer says Random / muliple cylinder misfire detected

look for a vacuum leak

Posted on Feb 27, 2009

  • 736 Answers

SOURCE: 2002 pontiac grand am 4 cylinder sedan cant pass emissions

not enough information so i will cover many possibilities:

new spark plugs would be a good place to start .. then replace the ignition wires, clean the coil insulator .. clean or replace the distributor cap .. when you replaced the O2 sensor that should have eliminated the "heater circuit" problem (the O2 sensor has a built in heater that gets it up to working temprature faster at warm up) .. .. if the wiring and connectors to the O2 sensor are ok then that fault code should go away .. multiple misfires will keep the trouble light on .. that could also be caused by a sticking or dirty injector or dirty throttle body.. you can use a good injector cleaner for that .also look for a cracked vacuum hose ... it would be good to know the present fault code since it should have changed once you installed the new O2 sensor .. there may be two O2 sensors (one later in the exhaust system) ..it sounds like you got the right one but make sure ..it may take some time for the computer to adjust to the new O2 sensor and for the injector cleaner to work .. make sure new plugs are gapped properly and use an "antiseize" compound on the threads .. that reduces the probability of the plugs sticking in their sockets .. on aluminum heads the plugs want to seize (or weld) in place after a long time. .. that makes them really hard to get out later .. just a tiny amount of antiseize compound on the theads helps a lot .. be careful not to overrtighten plugs in aluminum heads ..
if your engine is badly missing on one cylinder (you should easily detect that) then a sticking injector would be suspect .. there are some simple ways to get it working again if thats the case ..

Posted on Jul 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have Audi A6 Quattro have codes p0346,p0391 ,p0304,p0306,p0305,p0300 runs rough stalls makes a lot noise now power


P0346: Camshaft Position Sensor Intake Circuit Range/Performance Bank 2 http://www.autocodes.com/p0346_audi.html

P0391:Camshaft Position Sensor 'B' Circuit Range/Performance Bank 2
http://www.autocodes.com/p0391_audi.html

P0304: Cylinder 4 Misfire Detected http://www.autocodes.com/p0304_audi.html

P0306: Cylinder 6 Misfire Detected http://www.autocodes.com/p0306_audi.html

P0305: Cylinder 5 Misfire Detected http://www.autocodes.com/p0305_audi.html

P0300: Random Cylinder Misfire Detected http://www.autocodes.com/p0300_audi.html

Nov 24, 2016 | Audi A6 Cars & Trucks

1 Answer

System to lean bank, manufacturer control fuel air metering, cylinder misfire detected


Intake or vacum leak will be the first codes 174,171, try idle and spray propane around intake if car idles up, then intake is leaking, otherwise could be a broken vacum line, check with a gauge

Jan 18, 2014 | 2004 Hyundai Tiburon GT V6

2 Answers

Hi my 2006 cadillac cts has error codes po 300 303 305 343 347 368 392 and 496 can u tell me what they are or a website to find out thank u


P0300 is multiple engine misfire detected
P0303 is misfire in cylinder 3
P0305 is misfire in cylinder 5
P0343 is camshaft position sensor A (bank 1)
P0347 is camshaft position sensor A (bank 2)
P0368 is camshaft position sensor B (bank 1)
P0392 is camshaft position sensor B (bank2)
P0496 is EVAP Canister Purge System High Purge Flow

Jan 28, 2011 | 2006 Cadillac CTS

2 Answers

05 kia amanti with diagnostics codes p0350,p0320,p0300,p0302,p0303,p0304,p0305,p0306.skipping at times.when it does skip & misfire the rpm gauge goes crazy.this problem is not consitant


Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

Nov 17, 2010 | Kia Amanti Cars & Trucks

1 Answer

P134, p0141, po300, po130 and po135. 2005 Sunfire.


Given that most of the trouble codes are for the O2 sensor, I think I would change it. The multiple misfires could be because of improper fuel/air mixture caused by a bad sensor. Disconnect the negative(-) battery terminal then change the sensor. Disconnecting the negative(-) should reset the computer and allow the fuel/air mixture to return to default allowing the engine to start.
P0130 - O2 Sensor Circuit Malfunction (Bank 1 Sensor 1)
P0134 - O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)
P0135 - O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0141 - O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0300 - Random/Multiple Cylinder Misfire Detected

Jun 16, 2010 | 2005 Pontiac Sunfire

3 Answers

2003 Ford Ranger 4x4 extended cab- diagnostics checked and got these codes- P0171, P0174, P0300, P0316. Can you tell me what they mean?


P0171------ system too lean bank#1
Po174------ system too lean bank#2
For these 2 codes, try cleaning the maf sensor (mass air flow), that is mounted in the big black hose that goes from the air filter housing to the throttle plate, if it is dirty, that will cause those 02 sensors to send a signal to the computor to lean the air fuel mixture. If cleaning it doesn't work, the sensors will probably need changing.
P0300---- Random/multiple cylinder misfire
P0316---- Cylinder misfire at start up---- first 100 revolutions.
On those 2 codes, you have to do some testing to find out why there is a misfire.
Possible causes:
dirty/malfunctioning injectors
weak coil pack
fowling spark plugs/wires
Low fuel pressure

May 11, 2010 | 2003 Ford Ranger Regular Cab

3 Answers

Codes 1133-0131-0171-0300


p1133 - o2 sensor, Insufficiant Switching, Bank 1 Sensor 1.
p0131 - o2 sensor circuit, low voltage, bank 1 sensor 1
p0171 - Lean condition, Bank 1
p0300 - Random Misfire

I would be looking at the front passenger side oxygen sensor for issues. It may be bad, it may not be plugged in, bad wiring at harness.

The random misfire may be symptomatic of the o2 sensor problem.

Mar 17, 2009 | 2002 Chevrolet Silverado 1500

2 Answers

HELP, MISFIRING: 1999 Audi A6 Quattro Avant Wagon


P1127 Long Term Fuel Trim mult.,Bank1 System too Rich

P1129 Long Term Fuel Trim mult.,Bank2 System too Rich

P1250 Fuel Level Too Low

P1300 Misfire detected Reason: Fuel level too low

P0154 02 Sensor Circuit No Activity Detected (Bank 2 Sensor 1)

P0300 Random/Multiple Cylinder Misfire Detected

P0303 Cylinder 3 Misfire Detected

P0304 Cylinder 4 Misfire Detected

It sounds like there is a lot going on.

Good Luck

Brian

Sep 14, 2008 | 1999 Audi A6

Not finding what you are looking for?
2004 Chevrolet Astro Logo

Related Topics:

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...