Question about 1999 Lincoln Town Car

Open Question

The crankshaft pulley is lose and the belt fell off. If you tap the pulley back in and reconnect the belt, the pulley will move away from the motor and the belt will slip back off in a matter of seconds.

Posted by on

  • Fernand Luc Bergeron
    Fernand Luc Bergeron Dec 31, 2010

    have you thought of changing the belt for a new one ?

×

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Harmonic balancer/crankshaft pulley


Usually the balancer is all by itself then you transfer the pulleys to the balancer

Apr 15, 2014 | 1995 Toyota Tacoma

1 Answer

1996 Jeep Cherokee Sport - 6 Cyl /4.0 Liter - Crankshaft dampener fell off. Proceedure for reinstall?


You will have to buy a new pulley to crankshaft bolt and washer. Or did you find that as well when you picked up the damper? Probably fell off a long time earlier. Buy a used one from salvage, or get one from a Jeep dealer.
The damper should only go on one way. Or there may be a missing woodruff key. It would fit into a slot on the crankshaft, holding the pulley in a set position. If the woodruff key is missing, you will have to find one of them as well.
Working from underneath, remove the "belly pan" mounted below the front of the engine. Book says you MAY need to remove cooling fans and radiator for access-but that is for removing the old pulley with a pulling tool. You may be able to get it all back together without pulling the fans or radiator off. Put a little clean oil on the crankshaft, align the key slot of damper with crank key and tap the pulley on with a soft faced mallet or appropriate tool. Get the pulley on, tighten down the bolt tight as you can get it, then belts back on. Then go to a shop and have someone put an impact tool onto the bolt to torque it down to specs-80 FT-lbs.

Nov 24, 2013 | 1996 Jeep Grand Cherokee

1 Answer

How can I set the timing on a 1996 dodge stratus 2.4l engine


  1. Using sprocket installation tool No. 6792 or equivalent, press the crankshaft sprocket onto the crankshaft.
  2. Install the camshaft sprockets onto the camshafts. Install and tighten the sprocket retaining bolts to 75 ft. lbs. (101 Nm).


0900c152800896f5.jpg
enlarge_icon.gifenlarge_tooltip.gif
Fig. Fig. 4: Proper camshaft sprocket alignment for timing belt installation

  1. Install the crankshaft sprocket. Set the crankshaft sprocket to Top Dead Center (TDC) by aligning the notch on the sprocket with the arrow on the oil pump housing.
  2. Set the camshafts to align the timing marks on the sprockets.
  3. Move the crankshaft to 1 / 2 notch before TDC.
  4. Install the timing belt starting at the crankshaft, then around the water pump sprocket, idler pulley, camshaft sprockets, and then around the tensioner pulley.
  5. Move the crankshaft sprocket to TDC to take up the belt slack.
  6. Install the tensioner to the engine block, but do not tighten.
  7. Using a torque wrench on the tensioner pulley apply 250 inch lbs. (28 Nm) of tighten to the tensioner pulley.
  8. With torque being applied to the tensioner pulley, move the tensioner up against the tensioner pulley bracket and tighten the fasteners to 275 inch lbs. (31 Nm).
  9. Remove the tensioner plunger pin. The tension is correct when the plunger pin can be removed and replaced easily.
  10. Rotate the crankshaft 2 revolutions and recheck the timing marks. Wait several minutes and then recheck that the plunger pin can easily be removed and installed.
  11. Reinstall the front timing belt cover(s).
  12. Reinstall the engine mount bracket.
  13. Reinstall the right engine mount.
  14. Remove the floor jack from under the vehicle.
  15. Install the crankshaft damper and tighten to 105 ft. lbs. (142 Nm).
  16. Install the accessory drive belts and adjust to the proper tension.
  17. Install the right inner splash shield.
  18. Reconnect the negative battery cable.
  19. Check for leaks and proper engine operation.

Source: Autozone.com

May 22, 2013 | 1996 Dodge Stratus

1 Answer

Diagram for 5 pulley belt 98 pontiac transport.


start from bottom crankshaft pulley and ac compressor turn belt tensioner counterclockwise or lift forward then run pulley belt around crankshaft pulley and around AC compressor,run pulley belt around power steering pump then around alternator,once drive belt around alternator you done make sure drive is center of crankshaft pulley and AC compressor pulley.and belt back is center against water pump pulley before releasing the belt tensioner.

Aug 27, 2012 | Pontiac Trans Sport Cars & Trucks

1 Answer

How to position the timing belt crank shafts of 1997 mazda mpv


Raise and support the vehicle on jack stands. Remove the wheel on the passenger side of the vehicle using the drive ratchet and a socket. Remove the passenger side splash shield, using the drive ratchet and a 10mm socket. 2 Remove the accessory belt(s), using a wrench to loosen the tension. Unscrew the bolt from the crankshaft pulley, using the drive ratchet and a socket. Slide the crankshaft pulley and the timing belt guide washer directly behind it off the crankshaft.3 Remove all the 10mm bolts in the top and bottom timing belt covers. Remove the covers. The drive ratchet and a 10mm socket works well for this. 4 Push the crankshaft pulley on the crankshaft just enough to engage the keyway. Turn the crankshaft pulley clockwise until the timing mark on the top camshaft sprocket, which is marked with a line on the sprocket with a number 1 next to it, is lined up with the pointer straight up on top of the cover to the rear of the sprocket. Once the top mark is lined up, the crankshaft pulley's semi-circle mark should be lined up with the triangular pointer on the block. The marks on the crankshaft pulley should be straight up and the keyway should also be straight up. Remove the crankshaft pulley. 5 Loosen the tensioner bolt with a wrench, pull the tensioner to the left, away from the belt and loosely tighten the bolt to hold it in place. Remove the timing belt. 6 Install the timing belt counter-clockwise starting at the crankshaft pulley and move upward over the outside the water pump, on the inside the guide pulley and over the top of the camshaft, ending on the inside the tensioner. The main thing when installing a timing belt is to ensure the belt is as tight as possible opposite the tensioner. Get the belt tight between the crank sprocket and the cam sprocket so the tensioner can take out all the slack without moving the timing marks.7 Loosen the tensioner bolt and allow the tensioner to apply pressure to the belt. Use your hand to apply a slight pressure to the tensioner toward the belt and tighten the tensioner bolt. Check the belt tension to ensure it is not too tight or too loose. Check the timing marks again to ensure they still align. If the timing marks are not lined up, loosen the tensioner, move it back and repeat the last procedure over again until the belt is tensioned properly with no misalignment of the timing marks. 8 Install the crankshaft pulley temporarily and turn the pulley two complete revolutions, once again aligning the mark on the crankshaft pulley. Ensure the timing mark is still lined up perfectly on the camshaft sprocket. Reinstall the remaining parts in reverse order of removal

Oct 14, 2011 | 1997 Mazda MPV

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

1 Answer

Po306 code on a 1996 Chevy Lumina also ge a metallic squeak from the drive belt end of the motor. with the belt off as well


the bottom crank pulley is either lose! the keyway sheared and vibrateing against the crank sensor or the bolt in the crank pulley has backed off or fell out

Jan 21, 2010 | 1996 Chevrolet Lumina Mini

2 Answers

Timing marks on 1999 Ford Ranger 2.5L.


Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

  1. Loosen the alternator retaining bolts and remove the drive belt from the pulleys. Remove the water pump pulley.
  2. Loosen and position the power steering pump mounting bracket and position it aside.
  3. Remove the four timing belt outer cover retaining bolts and remove the cover. Remove the crankshaft pulley and belt guide.
  4. Loosen the belt tensioner pulley assembly, then position a camshaft belt adjuster tool (T74P-6254-A or equivalent) on the tension spring rollpin and retract the belt tensioner away from the timing belt. Tighten the adjustment bolt to lock the tensioner in the retracted position.
  5. Remove the timing belt.

To install:
  1. Install the new belt over the crankshaft sprocket and then counterclockwise over the auxiliary and camshaft sprockets, making sure the lugs on the belt properly engage the sprocket teeth on the pulleys. Be careful not to rotate the pulleys when installing the belt.
  2. Release the timing belt tensioner pulley, allowing the tensioner to take up the belt slack. If the spring does not have enough tension to move the roller against the belt (belt hangs loose), it might be necessary to manually push the roller against the belt and tighten the bolt.

The spring cannot be used to set belt tension; a wrench must be used on the tensioner assembly.
  1. Rotate the crankshaft two complete turns by hand (in the normal direction of rotation) to remove the slack from the belt, then tighten the tensioner adjustment and pivot bolts to specifications. Refer to the necessary illustrations. Make sure the belt is seated properly on the pulleys and that the timing marks are still in alignment when No. 1 cylinder is again at TDC/compression.
  2. Install the crankshaft pulley and belt guide.
  3. Install the timing belt cover.
  4. Install the water pump pulley and fan blades. Install upper radiator hose if necessary. Refill the cooling system.
  5. Position the alternator and drive belts, then adjust and tighten it to specifications.
  6. Start the engine and check the ignition timing. Adjust the timing, if necessary.

Nov 25, 2009 | 1999 Ford Ranger SuperCab

1 Answer

Inner crankshaft pulley moves 1/4 '' in and out


i think you need a new harmonic balancer. good luck.

Nov 23, 2008 | 1996 Toyota Tercel

Not finding what you are looking for?
1999 Lincoln Town Car Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

fordexpert

Level 3 Expert

5546 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...