Question about 2006 Pontiac G6

Open Question

Have a pontiac g5, battery was dead so I jump started it, now none of the remote functions will work, what's the problem

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 6982 Answers

SOURCE: i'm trying to jump a battery using a pontiac g5....

There is no battery in the world that does not have a negative terminal. but, the negative lead of the jumper should be connected to any solid metal bracket on the engine (on both vehicles) Stay away from drive belts.

Posted on Jul 29, 2009

  • 691 Answers

SOURCE: Remote start function on remote doesn't work

Replace battery first and see if that help, if not then follow steps below, if you cant figure it out or it still doesn't work, or take it to the dealer, it could be remote module is faulty. Keep the windows open as a safety measure, then,

Remove the ignition key from the ignition lock cylinder.

Remove the BCM PRGRM fuse from the fuse panel. Refer to Fuse Block in Wiring Systems.

Close all of the doors.

Close the liftgate.

Turn the ignition lock cylinder to ACC.

Turn the ignition lock cylinder to OFF, & then back to ACC within 1 second.

Open & close any vehicle door. A chime will be heard when the system enters the BCM programming/diagnostic mode.

Important
After 7 seconds, a chime may be heard confirming successful synchronization. It is necessary to wait approximately 14 seconds for a second chime that will confirm successful programming.


Press & hold the transmitter LOCK & UNLOCK buttons simultaneously for 14 seconds.

Repeat the previous step on each additional transmitter to be programmed.

Remove the ignition key from the ignition lock cylinder.

Install the BCM PRGRM fuse back into the fuse panel. Refer to Fuse Block in Wiring Systems.

Posted on Oct 07, 2009

  • 1 Answer

SOURCE: mY PONTIAC G5 REMOTE DOES NOT WORK TO LOCK OR

I had your exact problem. My fix was resoldering the battery contact where it mates on the circuit board of the remote. ( It should be connected at 3 places ) The center and left were not making contact. only the panic button side was. Works like new now. btw while its apart use a pencil eraser to clean the button contacts.

Posted on Nov 24, 2009

  • 12104 Answers

SOURCE: key locked in 2001 pontiac grand prix battery is

lock smith or someone authorized to use a slimjim[can do more damage if dont know how to use ]--or-- key fob wont work if vehicle battery dead if u can reach up under car at front and release hood latch then jump battery and then use key fob to unlock door

Posted on Feb 20, 2010

Testimonial: "thank u"

drsinister69
  • 2317 Answers

SOURCE: Jumped started Audi 2001 TT, due to dead battery, now radio dead

You will need to enter the anti theft radio lock code. I would check the manual for the operation. On my VW it was on a sticker in the truck. Also check with an Audi dealer for exact location.

Posted on Mar 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Pontiac G5 radio display is dead


Based on the information that you have provided. There's a possibility that there is a loose wire/connection possibly in the back of the radio. You would probably have to access the back of the radio and check the wiring harness.

Jun 08, 2016 | 2007 Pontiac G5 Gt Coupe

1 Answer

My engine light was on in my Pontiac G5 I was gone get checked but the next day my car doesn't turn on at all no light or nothing plus my keys are stuck


It sounds like your car battery is dead. If you connect another car as if you were going to jump-start your car - you ought to be able to remove the key - or crank the engine to start it.

You didn't include the year of your G5, so I don't know about recalls for it - as there seems to be one for the 2009 - linked below:

Ignition Key Stuck Due to Failed Shifter Pontiac G5 Common Drive Train...

May 22, 2015 | Pontiac Firebird Cars & Trucks

1 Answer

Can i jump start my 2008pontiac g5 from the front of the car


You should have a steel bolt coming up by the relay box that is your positive terminal for your battery, then connect to any unpainted metal to ground and presto there is a jumper spot .... or if you have a manual get it rolling put it into first when you have it rolling at a 5 km/h rough speed and release the clutch and start the car at the same time

May 02, 2014 | 2006 Pontiac G5

1 Answer

Pontiac G5 only starts when jumped. Battery tested out fine, Alternator tested out fine. Not running any codes...Now what?


Was the battery "load tested"? lotso f auto parts stores just test for 12 Volts across the terminals. You ned to have it load tested. Thats where a load simulating the starter is put on the battery. I have a carbon pile tester that places 500 Amps on the battery. many times I have seen a battery show 12 Volts and fail the load test due to a dead cell.

If it's a side terminal battery, it's really hard to get a good clean connection.

Jan 23, 2011 | 2007 Pontiac G5 Gt Coupe

1 Answer

Left key in OCC position with radio on. Key was stuck in ignitio


my battery die on my g5 when someone jump me i turn it on now my stereo wont work how do i fix it?

Jul 31, 2010 | 2008 Pontiac G5

2 Answers

I'm trying to jump a battery using a pontiac g5. where should i put the negative clamp of the jumper cable? the battery only has a positive post.


Place the negative cable on the frame of the car to ground it. It's best to do this even when there is a negative post present to protect the car and the alternator.

Jul 29, 2009 | 2006 Pontiac G5

1 Answer

2007 Pontiac G5 will not start


This is why it's not a good idea to use jumper cables on a newer car or truck. Those power packs are the preferred way of jump starting a car nowadays. You probably blew out the body control module and power train module in yours with the voltage drop from the dead battery. You'll need to contact your insurance company and a competent mechanic to get this car running again. In the meantime, check the fuses under the hood to make sure none of these are blown. You might get lucky there, but this is serious. The electrical system is expensive to work on in a modern car because of the electronics.

Dec 28, 2008 | 2007 Pontiac G5 Gt Coupe

Not finding what you are looking for?
2006 Pontiac G6 Logo

Related Topics:

164 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...