Question about 1998 Chevrolet Blazer

1 Answer

How to replace front wheel bearing on 4x4 blazer

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Passionate:

    Visited the website for 10 consecutive days.

    Habit-Forming:

    Visited the website for 3 consecutive days.

  • Expert
  • 107 Answers

On my blazer it wasn't real hard to do you take off the tire and there are 3 bolts on the back of the bearing holding it on and one nut in the middle of the bearing there is also a sensor on the bearing you take all of these off and the bearing should come off you may need to use a puller to get it off when you put the new one on make sure you torque the bolts and the nut or something could brake inside and you will haft to replace the bearing again.

Posted on Apr 24, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front wheel popping on 1997 blazer when turning right


is it 4x4? it could be your wheel bearing or front axle not sure on specs with blazer. one of those 2 tho

Sep 29, 2012 | 1997 Chevrolet Blazer

1 Answer

2000 Chevy Blazer 4x4...started making a horrible loud noise after my cruise control went out. I have recently replaced my hub and the brake pads and the CV axle. The noise comes and goes and only happens...


does it get louder above 45-60mph? and much quieter at low speeds. It could be wheel bearings, a rear differential or front differential. If its a grinding humming noise its wheel bearings, listenin to see if theyre coming from the front or rear, left or right, or both when your driving to know what wheel bearing are bad. If its a whinning noise, its probably a differential. check and listen to hear if its coming from the front or rear. Also, check for loose plastic around the wheels. Lastly check your tires for uneven or choppy wear. move your hands front to back on the top of the tire. does it feel really choppy and rough, maybe you just need new tires

May 04, 2011 | 2000 Chevrolet Blazer

2 Answers

Front wheel bearings bad how to replace 4x4 suppose to replace whole ensamble.need instructions how.


YES. after you take the brakes, rotors off, the bearing has 3 or 4 bolts, take those out and the 1 big nut off the end of the axle. the bearing unit should come out. grease the splined shaft before you put the new bearing on it. ,if you need to do front brakes, now is the time.

Oct 09, 2009 | 1998 Chevrolet Blazer

2 Answers

Paluse in front end when slow speed and feel it when breaking .what could it be if pinion idle arms ball joints wheel bearings are all solid ? IF front diff bearings starting to go how much is a kit and...


sounds like the rotors or warped. when slowing down with the brakes being pressed does the brake pedal pulsate? if so have the rotors resurfaced.

Aug 13, 2009 | 1996 Chevrolet Blazer

1 Answer

1996 Chevy S-10 Blazer


the front hubs on that are replaceable as a unit on each side. I suspect either a cv joint or bad bearings. pull the wheel and look at it if that is it it will be obvious. also , try putting it in fwd while you are moving at slow speed forwards. they can be tempermental.

Jul 20, 2009 | 1996 Chevrolet Blazer

1 Answer

2000 4 wd blazer loud whinning noise


Sounds like you have a bad bearing hub (likely in front but you need to determine which side) You really can't tell by shaking it, unless its falling apart. Remove front brakes and rotors and turn the bearing by hand, any slight roughness is a problem (you can't exert as much force as the vehicle weight of the vehicle)

Jun 08, 2009 | 2000 Chevrolet Blazer

1 Answer

Wheel bearing


the part can run from 150-200 and its about 2 hours labor(is this a 4x4?

Apr 19, 2009 | 2001 Chevrolet Blazer

3 Answers

Hub assembly and wheel bearings problem


Plan on spending more than $75 on this repair I am quite shore that that wont evan cover the parts. It definitely has a wheel bearing in the case of this vehicle it can only be replaced as an assembly that includes the hub. The ABS wheel speed senser is often sold as part of the assembly or in some cases is sold separately. good chance it will need to be replaced. Get the job done as soon as possible this is a very unsafe condition Your wheel will fall off while driving eventually if not repaired

Jan 06, 2009 | 2000 Chevrolet Blazer

2 Answers

I have a 2001 blazer with about 81,000 miles on it. I am being told that I need to replace the front wheel bushings and that this needs to be done prior to my 300+ mile trip to Minneapolis. I am being...


all 1998 and newer 4x4 blazers and s10s have front wheel bearing problems. If they are bad and you do not replace they can com apart then the only thing holding the wheel on is the axle shaft.

Nov 25, 2008 | 2001 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...