Question about 1987 Ford Bronco II

1 Answer

1987 ford bronco ll won't go in to 4 wheel drive when i push the 4 wheel drive button

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 376 Answers

Could be a faulty switch or the lock out on the diff may be bad, In woudl start at the switch first and work my way down.

Posted on Dec 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

We have a 1987 ford bronco full size 4 wheel drive , it was running fine we start it up runs fine then we drive it and it dies wont start again then while running ~ we replaced coil it is still doibg the...


Need to find out if it has a loss of spark or fuel when it dies.
Did you replace the coil because it had a loss of spark? Could be the ignition module. Auto Zones can test those for free.

Or is there a loss of fuel or low fuel pressure. Could be a weak/going out pump or a problem in its circuit.

Sep 11, 2011 | 1987 Ford Bronco

1 Answer

1987 Bronco II. When four wheel drive is engaged. Front drivers side wheel makes a whining sound. Four wheel drive won't engage.


i would believe that u prob have a bad lock out, change it and u'll be good to go, take only couple minutes if you have the right allen wrench

Jan 16, 2011 | 1987 Ford Bronco II

1 Answer

I replaced the fly wheel on my 87 bronco ll automatic 4x4 an now it wont move,what could make it not go


is the torque convetor all the way in the pump.when the tranny is bolted up to engine& convertor unbolted can you spin it if not its not all the way in pump .

Dec 21, 2010 | 1987 Ford Bronco II

1 Answer

Bronco locked in 4 wheel drive. light on instrument panel stays on.


can't get the 4 wheel drive 2 engage when i push the buttom 2 engage it

Nov 11, 2010 | 1987 Ford Bronco II

1 Answer

4 wheel will not engage


Sounds like the transfer case motor need replaced.

Jan 30, 2010 | 1988 Ford Bronco II

1 Answer

1991 Bronco wont go into 4 wheel high or low


sticky or broken lockout ,take apart and clean,inspect the center aluminum piece,if the center moves around alot then the lockout is broken,if not then regrease and try it again

Dec 30, 2009 | 1991 Ford Bronco

2 Answers

The 4 wheel drive doesn't work in my 89 Ford Bronco


The sound is not coming from the glove compartment, it is coming from the panel behind the drivers seat, that's where the relays and computer are located.
The relays click and apply power to a transfer case motor.
The motor attempts to turn a shaft that engages the front drive shaft.
When the computer thinks the shaft has NOT turned it tries again.
It will try three times then quit, figuring the shaft has not turned.

Get someone to crawl under the vehicle and engage the 4WD (just turn on the ignition- do not start the engine) See if they can hear the motor attempt to turn the shaft, it will make a clicking sound.
If not the connections or the motor may be bad.

I have found the most probable cause is the relays on the control board.
If you are technically adept --
you can remove the small side panel from behind the drivers seat and remove the control board. (remove the power plugs first)
Clean the relay contacts and bend them a little to give them more 'wipe' to keep them clean longer.
Put it back in and turn on the ignition.
Then push the RESET button on the side of the board.
Try the in / out 4WD a couple of times. If it doesn't work turn off the ignition, turn it back on and push the reset button again.

Oct 16, 2008 | 1989 Ford Bronco II

1 Answer

1992 bronco


the lock in the tranfor case is no good

Oct 05, 2008 | 1992 Ford Bronco

1 Answer

Rear brakes


take it to a shop and let them scan the computer and see if any codes come up.

Jul 04, 2008 | 1987 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

142 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...