Question about 1984 Ford Crown Victoria

1 Answer

Feels like it runs ona couple of cylinders - 1984 Ford Crown Victoria

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 46 Answers

Check plugs wires cap and rotor i&r if good check vacuum lines.

Posted on Dec 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to replace an ignition lock cylinder ona 1999 Pontiac Grand prix. But the key won't turn.


If you can't turn the lock cylinder, you may have to drill the cylinder out to remove it.

Sep 12, 2014 | Cars & Trucks

1 Answer

Ford Bantam rocam Clutch: How do I bleed the clutch?


Clutch bleeding on hydraulic slave cylinders are done in the exact same method as regular hydraulic brakes. If the slave cylinder has a separate reservoir, make sure it is above "MINIMUM" at all times. If it does not have a separate reservoir, then it works together with the master cylinder for the brakes, make sure that one is above minimum too. Pump the clutch pedal a couple of times (note you will rarely feel any resistance in the pedal), hold the pedal down, and have someone open the bleeder valve on the slave cylinder. Close it when no more fluid comes out with pressure, then rinse and repeat until the clutch pedal feels ok.

Jan 09, 2014 | 2006 Ford Bantam 1.6i

1 Answer

Does anyone The water pump is ona dodge arias


If you are asking where the water pump is, and if the engine is a 2.2 four cylinder, its on the passenger side of the block.

Feb 28, 2013 | Cars & Trucks

1 Answer

Firing order for a 1983 plymouth grand fury with a 318 engine


1-8-4-3-6-5-7-2

Distributor roatation is clockwise; odd cylinders are on left side of vehicle with #1 at left front.

Oct 04, 2012 | 1983 Dodge Pickup

1 Answer

How to set distributer chevy 91 s10 4.3 v6


start by removing the number one spark plug. you will need to get that cylinder up to its compression stroke and and to the top of the cylinder by turning the engine over and feeling the air rush out of the hole. once piston is at the top set the distributor into its place making sure that rotor is pointing at the plug wire position for the number one cylinder after its fully seated into position.. it may take a couple stabs as the rotor will turn on its own while being dropped into place.. be sure it seats all the way down cause the distributor also runs the oil pump.

Jul 08, 2012 | Chevrolet S 10 Cars & Trucks

1 Answer

Approximately how many hours in replacinga Daihatsu water pump ona 1.5 litre charade?


I'm not sure about the 1.5 liter engine as your vehicle for that year came with a 1.0 liter 3 cylinder engine and a 1.3 liter 4 cylinder engine. I didn't see a 1.5. In any case when I looked it up if you have the 1.0 my labor guide shows 1.5 hours. If you have the 1.3 the labor guide shows 2.5 hours. Sorry i couldn't find the engine you said you had. I hope this helps and good luck

Mar 09, 2011 | 1992 Daihatsu Charade

1 Answer

Thermostat installation for nissan pick up 1996


Follow the top radiator hose. It goes right to the thermostat. Make sure that the little hole in the new thermostat it up when installing.

Aug 02, 2010 | 1996 Nissan Pickup

1 Answer

Laguna 2.0 16v 2003 plate not running smooth when low revs


Might be, have a fuel pressure test done on it, that will show if there is a fuel problem, or there is something else causing it.

Aug 25, 2009 | 2000 Renault 181

2 Answers

I have no pressure in the clutch and changed the master cylinder


you need to bleed master & slave cyl master dont hold much fluid must bleed similar like brks when when starts coming out of bleeder close bleeder let sit couple of minutes air travel top of master pump pedal more repeat pumping pedal air residue will work it self out

Aug 11, 2009 | 1997 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...