Question about Subaru Outback

Open Question

2003 subaru outback repair manual - Outback Subaru Cars & Trucks

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: what oil grade do i need in 2002 subaru outback?

Probably 5w40 synthetic

Posted on Oct 09, 2008

Ad
blueextc3221
  • 15935 Answers

SOURCE: needdrive belt diagram for Subaru outback 3.0

8c0dd6e.gif
Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on May 23, 2009

  • 484 Answers

SOURCE: serpentine belt

<img src="http://www.mvreader.com/multiview/dayco/graphics/rtdiag/bkc.jpg" alt="2003 SUBARU OUTBACK - H6 3.0L 3000cc GAS FI N EZ30D" /><br>The website mvreader.com/multiview/dayco has listings for most cars' serpentine belts, as well as their installation instructions.

Hope this helps out,
matthew

Posted on Oct 22, 2009

techbuster
  • 5081 Answers

SOURCE: how do u put timing belt for 2001 subaru outback

This is not your average timing belt replacement due to being a double overhead cam that is also an interferance fit.First remove cooling fans.2-Loosen drive belts and remove.3-Remove crank pully.4-Remove timing covers.You will see 4 cam sprockets.Theses sprockets contain single and double referance marks.You will be using the double referance marks.Rotate engine until the double referance marks are facing each other.This is to be done the same way that the American autos timing Chain systems are done but you will have 2 small double lines to line up not dots.The next step is the most important step and is of utmost imortance.THE CAMSHAFT HAVE TO BE LOCKED IN PLACE--FAILURE TO DO SO CAN RESULT IN BENT VALVES.The cam sprocket holders can be bought or rented.You can make your own as well by making 2 wedges with bolt through the middle.Slip in between sprockets and tighten enough to hold sprockets.Do not use excessive torque while tightening wedges sprockets are not made of steel but rather a composite material.Next you will have to remove the tenioner.The tensioner has to be retracted and pin istalled to hold in retracted position.The tension device has to be retracted with care or will be damaged.You can not exceed 50 pounds pressure on the plunger.The simplest method is to reract while still in vehicle, it takes 15 minutes to properly retract the plunger.By pulling up on the tensioner by hand with about 18 pounds of force --50 will be exerted at the plunger.When fully retracted insert pin to hold in reracted position.Next check to make sure that cam wedges are holding and no sprocket are trying to move,when satisfied remove one of the rollers at the bottom on the side where you left hand would be standing in front.Pull off belt.Replacement belt will have referance marksone line will go to crank sprocket face up others will line up with other sprocket marks.Reinstall roller followed by tensioner then pull pin you have holding tenioner retracted.Remove wedges.Reinstall covers fans belts.Do not be intimitaded by this replacement.Everything is very easy to get to.Be sure cams are locked and that damage is not done to tensioner and it is straight forward.

Posted on Nov 06, 2009

  • 58 Answers

SOURCE: 1996 Subaru Outback Engine Code P0170

P0170 Fuel Trim Malfunction (Bank 1), could be fuel filter, mass air sensor, or low fuel pressure.

Posted on Jan 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Subaru outback h6 3.0. Starts fine, when I shift into reverse or drive I get a loud grinding noise


Is your 2003 Subaru Outback automatic or manual transmission?
If it is automatic, then your transmission sounds like it's malfunctioning into the reverse gear as it is not aligning properly.
If it is manual, then your transmission sounds like it may have a bad clutch or bad reverse gear.
Either solution is not cheap. Good luck.

Apr 20, 2013 | Subaru Outback Cars & Trucks

1 Answer

How do i locate the fuse box in a subaru 2003 outback


On this website you find fuse box diagram and description for Subaru Outback (2003)

SubaruOutback 2003 fuse box diagram Auto Genius

Feb 05, 2012 | 2000 Subaru Outback

1 Answer

Where can i find how to feed a belt for a 2003 subaru outback H6 3L


This site may help (or get a Haynes manual for your vehicle)

http://www.google.com/imgres?imgurl=http://www.subarugirlies.com/howto/v-belts/subaru-v-belt-change1.jpg&imgrefurl=http://www.subarugirlies.com/howto/v-belts/subaru-belt-swap.html&h=547&w=914&sz=168&tbnid=5BTNdWN9A19IQM:&tbnh=88&tbnw=147&prev=/images%3Fq%3Dsubaru%2Bengine%2Bbelt%2Bdiagram&hl=en&usg=__rzmsdNn8KFMdUS80RakGRAMfYdg=&sa=X&ei=CFQvTInjBoOClAeW_OW7CQ&ved=0CB4Q9QEwAA

Jul 03, 2010 | 2003 Subaru Outback

2 Answers

2004 Outback wagon needs new head gaskets


If its not a Recall then no they wont pay for anything

Apr 04, 2010 | 2004 Subaru Outback

1 Answer

Replace mirror on 2003 subaru outback


take the triangle plastic trim cover off from the inside which conceals 10 mm bolts that mounts the mirror

Mar 02, 2009 | 2003 Subaru Outback

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...