Question about 2002 Nissan Frontier Crew Cab

2 Answers

Hazard lights and signals dont work. fuses and bulbs are good

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Where is the hazard light relay LOCATED? Can't find it

Posted on Dec 09, 2016

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 66 Answers

Most likely you have a bad relay. Relay's typically control more than 1 source or part, and you will usually find the relay inside of the Hazard switch itself. Call your local Nissan dealer and run that by them to make sure thats common for that model too. If so, picking up a new Hazard switch should be relativley cheap and easy!

Posted on Dec 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hazard lights work but not turn signals


hi. see if it as a relay in the circuit. most car lighting these day have
relays. mines got loads. good luck

Feb 23, 2014 | 1989 Toyota Camry

1 Answer

Turn signal hazard lights work but not running lights


The parking lights should be on a different circuit from turn signals - hazard lights. The bulbs usually have two filaments, one for each circuit.
On most models there is a tail light fuse and relay that handles front and rear parking lights.

Jun 28, 2013 | Toyota Tacoma Cars & Trucks

1 Answer

95 mustange gt brake light dont work check #9 fuses change all bulbs replaced switch on brake pedal hazards lights works ,parking or running lights works,turning signal lights works,what other places i...


I assume the fuse has power if the hazards work.
The third brake light skips the turn signal switch, the regular brake light circuit goes thru the turn signal switch.
Do you have power going into the turn signal switch on the red lite green wire from the brake switch ?

Feb 17, 2013 | 1995 Ford Mustang

2 Answers

!997 Ford Thuderbird brake lights and hazards do not work


Lets start at the beginning.
The turn signals and brake lights use different fuses but both go thru the turn signal switch and use the same bulbs.
Have you checked the fuses for each circuit and does each switch have power in and out ?

Feb 03, 2013 | 1997 Ford Thunderbird LX

1 Answer

My brake, hazard and turn lights dont work, i


well u have two seprate problems the hazards and turn signals have a flasher that needs replacing if the fuse is good on the fuse box marked signals .and there is a brake light switch under the dash board near the brake pedal it has two wires on it check the wires make sure they are connected if so replace the brake light switch

Nov 13, 2009 | 2002 Chevrolet Astro

2 Answers

No brake lights, turn signals, or 4-ways.


Did you actually check the bulbs? I believe your brake lights, signal lights, hazards all use the same bulb for each side.

Your brake lights may be your brake switch just above your brake pedal.
The signals could be your electronic flasher module (EFM) located under the dash near the steering column.
Your hazards may be affected by the EFM, but not likely and the switch for your hazards may be faulty

Sep 10, 2009 | 1998 Chevrolet Blazer

2 Answers

My headlights don't work, my tail lights dont work. my brake lights work. when i use my signals they act like hazards. fuses are good. what could the problem be?


short in main harness.. but first i would check all bulbs... by this i mean pull out each bulb look at base make sure the two contact on bottom base of bulb are not melted together... aslo look good inside bulb.. to make sure the two elements inside bulb are not shorted....don't forget to check the wires to the towing plug if have one

Sep 04, 2009 | 1983 Chevrolet Blazer

1 Answer

My blinker lights wont work by themselfs but theyll work on the hazards and the fuse is good i dont know whats wrong


It is the switch. Some call it a combination switch. The lever that works the turn signals, may also work the wipers thats why its called a combo switch. If the work with the hazards, then that tells you that the fuse, wiring, bulbs are all good. Has to be the switch.

Sep 03, 2009 | 2005 Chevrolet Impala

1 Answer

Turn signals and hazards dont turn on


The turn signals run through the hazard switch, I have replaced hazard switches for this problem.

Apr 22, 2009 | 1996 Honda Accord

Not finding what you are looking for?
2002 Nissan Frontier Crew Cab Logo

Related Topics:

209 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...