Question about 2003 Saturn L-Series

1 Answer

CRANK SHAFT SENSOR - 2003 Saturn L-Series

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Saturn Master
  • 6,826 Answers

To remove the sensor:

  • Disconnect the wiring harness.
  • Unbolt the sensor mounting bolt.
If the crankshaft timing sensor or the camshaft reference sensor is removed, follow this procedure when the sensor is replaced:
  • Thoroughly clean the sensor tip and install a new spacer on the sensor tip. New sensors should be supplied with the spacer installed.
CRANK SHAFT SENSOR - fr_24.15.gif Spacer on crankshaft timing sensor and camshaft position sensor.
  • Install the sensor until the spacer lightly touches the sensor ring, and tighten the sensor mounting bolt 105 in.lb.

Posted on Dec 31, 2010

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

wracefans24
  • 1985 Answers

SOURCE: crank shaft sensor? is this the same as cam shaft

no each one has its own job,
crank sensor is counting crank shaft rpms
cam sensor is counting cam shaft rpms
is there any lights coming on just as this is happening?
i think you should have the fuel pressure checked when it dies out,you need at least 50psi at fuel rail

Posted on Dec 09, 2009

mkv0525
  • 358 Answers

SOURCE: PO340 Crank Shaft Sensor "A"C came up as the problem Also a C1201 Just want to find out where the Crank Shaft Sensor is located. Thank you

89119318this should help.

Posted on May 21, 2009

  • 34 Answers

SOURCE: crank shaft sensor

o.k... on the very botton of the engine... right above the harmonic balancer... better known as the crankshaft pully... it shold be just off to the side a little

Posted on Oct 25, 2008

  • 383 Answers

SOURCE: CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA

1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.

Posted on Apr 06, 2009

  • 41 Answers

SOURCE: Crank shaft position sensor

it should be behind the harmonic balancer at the driver side , front of the oil pan

Posted on Sep 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Locate crankshaft sensor on 1996 crystler New yorker (where is the crank shaft found on a 1996 Crystler NewYorker?


The crank shaft is actually an internal mechanical part of the engine (see last picture) however the crank shaft position sensor uses through what they call a "hall effect" with a componant inside the transmission. The crank shaft turns which in turn turns the componant inside the transmission. Below are a couple of pictures of the location of the crankshaft position sensor as well as what the plug looks like so you know you are removing the correct part. Hope this helps.....

1_17_2012_1_55_30_pm.jpg

1_17_2012_1_55_54_pm.jpg

1_17_2012_1_56_30_pm.jpg

1_17_2012_1_56_58_pm.jpg

1_17_2012_1_57_19_pm.jpg

Jan 17, 2012 | Cars & Trucks

1 Answer

Van runs good then stalls out. then hard to start. If i let it sit for 5 minutes it starts again no problem. Then stalls again shortly there after.


This sounds like a failing camshaft position sensor and weak crank shaft sensor .When crank shaft sensor gets weak it will stop functioning.When crank shaft sensor stops working then ECM will not control fuel system and the fuel will stop flowing. And this can cause the problem.When crank shaft sensor gets heated it will stop working, but when the car shuts off, the sensor gets cold and works for few minutes and sensor again gets hot and it stalls. ---------- Get the crank shaft sensor tested on your Chevrolet venture. ---------- There are many other possibilities for this stalling problem,but crank shaft problem is indicating in your case. For more details, click the link below:--- http://howtobyme.blogspot.com/2011/10/stalling-problem-on-2000-chevrolet.html ------------ This should help.Thanks.Helpmech.

Oct 13, 2011 | 2000 Chevrolet Venture

1 Answer

I would like to know if the cam sensor and the crank shaft sensor are one of the same or two different items


They are two different items. The cam sensor reports the position of the cam shaft(s) which operate the valves. The crank shaft sensor reports the position of the crank shaft, ie the position of the pistons.

May 19, 2010 | 1998 Chevrolet Malibu

1 Answer

Computer shown problem with crank shaft sensor


The first thing you should do is remove your new crank shaft sensor and clean the mount point with a degreaser and your connectors with contact cleaner and a wire brush. Once you do this you should put your crank shaft sensor back in and see if it works if not i would suggest bring it back to the shop you got it and trying to have them replace it because more then likely if it still dose not work you may have gotten a bad censer out of the box.

I hope this helped you.

Thank you,
Norse

May 16, 2010 | 1999 Hyundai Sonata

1 Answer

Where is the crank shaft sensor located on my 2000 alero?


CRANK SHAFT SENSOR FOR A 2.4 ENGINE NEXT TO OIL FILTER.FOR THE 3.1 - 3.4 ENGINES CRANK SHAFT SENSOR LOCATED BEHIND CRANKSHAFT PULLEY.

Mar 18, 2010 | 1999 Oldsmobile Alero

1 Answer

Crank shaft sensor? is this the same as cam shaft


no each one has its own job,
crank sensor is counting crank shaft rpms
cam sensor is counting cam shaft rpms
is there any lights coming on just as this is happening?
i think you should have the fuel pressure checked when it dies out,you need at least 50psi at fuel rail

Dec 08, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

1998 hyundai accent


make sure crank sensor is all the way seated care taken 10mmnut dont over tighten or you will break sensor

Sep 23, 2008 | 1997 Hyundai Accent

Not finding what you are looking for?
Cars & Trucks Logo

198 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...