Question about 1999 Ford Expedition

Open Question

How to remove rear door panel on 99 ford expedition

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1986 Answers

SOURCE: rear door panel removal

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

  • 295 Answers

SOURCE: how remove the rear inside door panel on a 2001 oldmobile aurora

The inner door panel is held in by clips and screw.
Look at the door near the door handle there should be screws holding it in and along the outer edge of the door. Once loose, and the door handle removed or the arm rest removed. The door panel then prys out , because of the clips that hold it on. Then pops out by applying pressure to the panel upward to the top of the door. The clips always break because of the design and plastic.

Good luck

Posted on Mar 21, 2009

lilward5
  • 5 Answers

SOURCE: how to remove front driver side door panel (2000 ford expedition)

There is a triangular piece, at top corner, covering a screw behind the mirror. Remove that screw. Remove the piece that covers the handle and remove the screw holding the handle to the door. Look through, where door handle was and remove another screw just above where the handle was. This screw is holding the panel to the actual door. Pop the cover off for the automatic door locks and disconnect them. Lift the panel in an upward direction.

Posted on Nov 14, 2009

  • 3 Answers

SOURCE: Remove door panel on a Ford Van

For a 1999 Ford Econoline 150 (assume the same or very similar), remove triangular plastic cover over mirror assembly by prying straight out, remove plastic door handle cover by prying up from the front side, remove electronic door switches by prying up from back side, remove round plastic cover at bottom rear of door panel. Four screws are now revealed, remove them. Lift door panel straight up, clips are hooks (not snap in). Work door switch assembly out of door panel. Set door panel aside. Reassemble in reverse order.

Posted on Nov 21, 2009

  • 255 Answers

SOURCE: how to remove rear door interior door panel

You should obtain a tool made specifically for removing door panels. They are attached by "snap" connectors, and by pulling on the door panel itself will invariably ruin it. Get the tool from a parts place and carefully peer into the slot between the door metal and the door panel. Use the tool slowly with resolution. You should really acquire a manual that guides you for your particular Jag.
Remember, to take the panel completely off, you need to remove the door handle. Look for a plug that has a screw under it. You'll need to pop the door window/lock control panel too, to access screws under there. This can be tricky, so be careful.

Posted on Nov 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove right front panel on 2000 ford


This is for the front passenger side door panel from a 1999 Ford Expedition. The driver's side door should be the same, except for the mirror switch which needs to be unplugged. The 1998 *might* be the same, I don't know, but this should be helpful to someone.

Use a flat blade screwdriver or other suitable tool to pry out on the top of the triangular plastic panel on the top front of the door panel. The plastic holder should pull out of the door. Now pry up on both sides of the triangular panel and pull it loose. Remove the philips head screw you find under this panel. Pull the door latch handle, pry out the insert where the handle goes through, and remove the bolt that holds the door handle in place. Remove the door handle. Pry up on the ends of the door switch panel to remove it. Unplug the cables by pushing in on the lock tab on the side of the plug and pulling out. Remove the philips head screw accessible through the switch panel hole. Insert a flat blade screwdriver into the slot at the bottom of the courtesy light lens and pry up and out to remove the lens. Remove the philips head screw behind this lens. Pull up on the door panel to remove it. Be careful of the courtesy light when removing the panel - give the light a quarter turn counter-clockwise from the rear to remove it from the door panel.

Its possible that this GUIDE can helpfull as reference.

Hope this help.

Apr 22, 2010 | 2000 Ford Expedition

2 Answers

I'm trying to replace rear speakers in my 99 ford expedition and i'm trying to find out the size and how to install


Ford usually fitted elliptical speakers in their models in the 1990's so it's possible that yours are 6"x9" or something similar.
You can get replacements from Ford, (which are usually very expensive!) or buy some better ones on the Internet, such as Ebay or Amazon.
I bought a pair of German Blaupunkt 6x9's for my car from some site I found on Ebay and the price was around half of that to buy the *same* speakers from Ford Spare parts Dep't!!!
The sound is fantastic!

PS: You should be able to access the rear speakers below the rear parcel shelf at each side of your Expedition. They are held in place by 4 screws, which usually have a Posidriv (+) type screwdriver head.
When refitting, make sure!!! that you fix the +ve spade terminal to the +ve marked on your new speaker & the -ve terminal to the -ve. Do this on both speakers to make sure that they are both in-phase (so both bass drive units are pushing air forwards together). If you don't keep them in phase, the speakers will produce much less bass - which is clearly noticable!

Hope this helps

Nov 17, 2009 | 1999 Ford Expedition

1 Answer

Ford expedition side mirror (instalation giude)


SECTION 501-09: Rear View Mirrors 2003 Expedition/Navigator Workshop Manual REMOVAL AND INSTALLATION Exterior Mirror Removal and Installation
  1. Remove the front door trim panel. For additional information, refer to Section 501-05 .
Front Door Trim Panel —Expedition Removal and Installation
NOTE: Left front door shown, right front similar.
  1. Remove the door handle bezel.
    • Use service notch.
  1. Remove the window control switch plate.
    • Use service notch and disconnect the electrical connectors.
  1. s3j~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the door trim panel, lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
    Remove the two bolts and three screws, and remove the door trim panel.
  1. Remove the weather shield.
  1. Disconnect the exterior mirror electrical connector.
  1. Remove the exterior mirror.
    • Remove the nuts.
cf86471.gif
  1. To install, reverse the removal procedure.
    • Install top nut first.
---
Exterior Mirror Motor Removal and Installation
  1. Position the mirror glass to obtain a gap at the top edge of the mirror and carefully pull the top edge of the glass away from the mirror housing.
  1. Disconnect the heated mirror electrical connectors.
  1. Remove the exterior mirror motor screws and exterior mirror motor.
    • Disconnect the electrical connectors.
  1. To install, reverse the removal procedure.

Oct 26, 2009 | 2003 Ford Expedition

1 Answer

1997 ford expedition window won't go up... how do


Remove sail panel cover for mirror, remove screw. Remove window switch cover and remove screw. Remove courtesy lamp lens on door and remove screw. Remove inside door handle trim cover and remove 8mm bolt and handle. Lift upwards and remove door panel.

Oct 08, 2009 | 1997 Ford Expedition

2 Answers

Ford Expedition rear hatch won't open


where is the rear door fuse located on a 2000 ford expedition?

Jul 11, 2009 | 1998 Ford Expedition

1 Answer

Actuator removal


please rate as solved if this is what you need. You will need to borrow a heavy duty riveter from autozone or wherever you buy the lock cylinder from.


Removal
  1. NOTE: The rear door window glass must be completely raised.
    Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
  1. Remove the rear door trim panel. For additional information, refer to Section 501-05 .
Trim Panel —Rear Door, Expedition Removal
  1. Remove the power window switchplate (14524).
  1. Disconnect the electrical connector.
  1. Remove the rear door handle trim cover.
  1. Remove the rear inside door handle.
    • Remove the door handle bolt.
  1. Remove the rear door trim panel screws at bottom of panel.
  1. s2j~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: To avoid damage to the rear door trim panel, do not pull directly outward.
    Lift upward and then outward to remove the rear door trim panel (27406).
  1. Remove the rear door watershield.
  1. Disconnect the power door lock actuator electrical connector.
  1. Drill out the power door lock actuator rivet.
9ac2386.gif
  1. Remove and discard the screws.
  1. Remove the power door lock actuator.
    • Disconnect the power door lock actuator rod.
Installation
  1. NOTE: Use new screws when installing the rear door latch.
    To install, reverse the removal procedure.
    • Use Heavy Duty Riveter to install the new rivet.

Jun 14, 2009 | 2002 Ford Expedition

1 Answer

99 expedition heater valve


yes to the first question
and yes it is the blend doors
recommend get another unit for the control or take that control out and see if one of the tubes is broken off the control unit

Dec 15, 2008 | 2000 Ford Expedition

1 Answer

99 ford expedition power window


no, you will have to remove the window motor to raise the window up manually.

May 15, 2008 | 1999 Ford Expedition

Not finding what you are looking for?
1999 Ford Expedition Logo

Related Topics:

581 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5470 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...