Question about 2002 Chrysler 300M

2 Answers

Tail lights work, all brake lights don't. Checked fuses and all ok. Looked at wiring and all seems ok. Help!

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 22,095 Answers

Stop light switch ?

Posted on Dec 31, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 11,896 Answers

There is a switch above the brake pedal. This switch is for the brake lights. You can use a voltmeter or continuity/ohm meter to test for resistance or continuity.
If the fuse is good and bulbs are good and all wiring tests out to have good continuity, then the switch is likely bad or it slipped out of place

Posted on Dec 31, 2010

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2418 Answers

SOURCE: Need to solve towbar wiring fault for trailer

This sounds a bit crazy, but you do not have a good solid ground to your trailer brake lights. You may have to run a separate ground wire from the trailer to the car. Pull your trailer close to the front of your car, close to the battery. Use some wire to connect your trailer to the battery. Then touch each contact one at the time until you learn which port turns on which light(s). Using the wires, only one in the ground connector and the other in the brake connector. gain access to one or both sides of the trailer lights, use another wire and touch the base of the bulbs to the metal of the trailer if the light gets brighter you need to run another ground wire. Hope this helps FixYa up.

Posted on Jul 31, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Tail lights not working


Inspect wiring and contacts...cud bebad ground. Mite b a module prob

Jan 25, 2016 | 2002 GMC Envoy

1 Answer

No brake lights, blubs and fuses ok. center brake light DOES work


Usually when the third brake light works but the regular lights don't the problem is in the turn signal switch.
I would check for voltage there.

Jul 19, 2012 | 2004 Jeep Grand Cherokee

2 Answers

I have a 2000 chevy 2500 and the tail lights, tag lights and brake lights have stopped working, I checked the bulbs and they are good, fuses are good. Have not replaced the brake relay under the hood. Do I...


check for power at the wires going intop the tail lights, real common that the circuit board is bad, but unlikely both at the same time. The tag, tail lights and brakes are 2 different systems. Do the turn signals work normally? if so the wiring from the turn signal switch to the brake lights is GOOD. the stop light switch had\s a ORANGE wire that should have 12V if not ck STOP LPS fuse, when brake pedal is depressed, the WHITE wire is 12V (at the stop light switch) if that is OK, the turn signal switch COULD be bad. The wiring harness plug is near the back left under the tailgate, see if that is disconnected?

Aug 04, 2011 | 1999 Chevrolet K2500

2 Answers

I have a 1996 dakota with no tail lights. The brake lights work. I think it may be a fuse, but I don't have a manual to see what fuse it may be,????


Why would it be a fuse?
You have front parking lights? Then no fuse

If it was a fuse ---would that fix it -- NO it wouldn't
Why do fuses blow?

Have you even removed the tail light housing & checked the bulbs,
or checked the sockets for ground or under truck for wiring
harness issues?

Don't need a manual to check all fuses under the dash &
in the box near brake booster

Jul 01, 2011 | 1996 Dodge Dakota

2 Answers

Rear tail lights not working


If both tail lights are not working it is likely to be a fuse or bad connection under the hood or a connector at the back see if you can trace the wires to a connector and see if it is dirlty or corroded.

Mar 02, 2010 | 1996 Dodge Dakota

1 Answer

Rear brake lights don't work


you prob got a trailer plug prob bad wires if not tail lights run through turn signal switch tell fix ya bout me ok

May 23, 2009 | 2005 Chevrolet Silverado 2500HD 2WD

1 Answer

Tail lights don"t work, brake and signals ok


Check for dash/ instrument lights. I would say there is a fuse bad and you just haven't found it yet.

Feb 08, 2009 | 2002 Kia Sedona

2 Answers

Tail Lights, Marker Lights, Air Conditioner lights out


it seems to be a wiring problem .get the wiring checked.

May 22, 2008 | 2005 Pontiac Vibe

Not finding what you are looking for?
2002 Chrysler 300M Logo

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...