Question about 2004 Honda Accord

Open Question

In removing intake manifold on honda accord to replace starter motor would you have to replace any gasket or any sealing please help thank you

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 625 Answers

SOURCE: changing spark plugs 2003 Impala 3.4 eng. i.e. removing and reinstalling upper intake manifold

it will require new manifold gaskest it may take between 2 to 3 hrs of your time but not any special tools need it.

Posted on May 28, 2008

Ad
  • 1 Answer

SOURCE: replacing a 97 honda accord starter

i haven't fixed the problem but I don't have any money to pay for a plan on here. thank you anyway.

Posted on Jan 15, 2009

  • 9 Answers

SOURCE: 1994 Honda Accord heater nor A/C will not blow air

if your not getting any air coming out of the vents then your problem is your blower motor. test the wire harness to see if its getting power,if it is then your blower motor is bad if its not getting power then check your relay.

Posted on Jan 17, 2009

lasvegasrich
  • 65 Answers

SOURCE: intake manifold gasket / replace

3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.

  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Posted on Sep 16, 2009

  • 14 Answers

SOURCE: intake manifold gasket replacement? radiator has a

nah its pretty simple for the upper intake. 10 to 12 bolts.

Posted on Oct 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Need a engine diagram for a 2.8 ltr v6 showing rear main seal


Just a little advise before you jump to thinking the rear main seal is leaking. The vast majority of the oil leaks from these 2.8L motors are the rear intake manifold seal and the distributor o-ring. I would check them first. The rear main seal is in the lower rear of the motor, you have to remove the transmission to replace ti.

Jan 22, 2011 | Pontiac Firebird Cars & Trucks

1 Answer

Where is the starter located on a 2001 cadillac


The starter is located under the intake manifold. Remove the intake manifold and all necessary components to access it.It is advisable that while replacing the starter also replace all the gaskets with new gaskets .This helps.
Thanks. you can rate this solution and show your appreciation.

May 19, 2010 | 2001 Cadillac Catera

1 Answer

Replace starter on 2003 Honda Accord w/4 cylinder. Steps to take to remove and install new starter.


disconnect the cable to the battery........there is 3 bolt holding the starter to the engine/transmission housing. You may need to remove the air intake manifold to gain access to the work area.

Mar 20, 2010 | 2003 Honda Accord

1 Answer

Just replaced the starter on a 2002 Acura RSX. had to remove the intake. after the motor warms up the RPM's start to hunt. Did not replace the intake gasket. could this be the cause?


If the RPM's are going pretty low to where the car seams like its about to die, then it could be a vaccum leak. Whick could be cause by a bad gasket or something maybe didnt get sealed right when putting everything back together. If you do decide to change the gasket, i would recommend the "Hondata Intake Manifold Gasket". Its thicker and not made from metal and also keeps your intake manifold cooler.

Mar 04, 2010 | 2005 Acura RSX

1 Answer

Replacing starter for 1991 Honda accord lx with pics


If you want to change the starter motor, first disconnect the positive cable to the battery. Then under the intake manifold on the passenger side and between the engine and the firewall you should see the starter motor. It has a large cable that comes directly from the battery and a small wire that comes from the ignition. Disconnect both of them and then there should be two bolts that thread into the engine block, one on the top and the other one on the bottom. remove those and the started should be free. Replace in reverse.

Jan 11, 2010 | 1991 Honda Accord

1 Answer

I have a 2001 honda prelude its leaking a lot of oil from under intake mani fold i just dont know from where any ideas?


it is most likely leaking from the seal at the front of engine gasket between the manifold and motor. the manifold will have to be removed an new gaskets installed.

Nov 29, 2009 | 1996 Plymouth Breeze

1 Answer

Locating the starter motor on a 2004 honda accord


Disconnect the negative battery cable. Disconnect the positive battery cable (if you have an anti-theft audio system, make sure you have the code).
Drain the cooling system. Remove the intake manifold ( not a real easy task).
Disconnect the starter cable from the B terminal on the solenoid. Disconnect the BLK/WHT wire from the S terminal.
Remove the harness clamp. Remove the harness holder.
Remove the starter retaining bolts. Remove the starter from the vehicle.
d6afbbe.gif
Hope this helps you find it.

Nov 18, 2009 | 2004 Honda Accord

1 Answer

Intake manifold gasket / replace


3.8L Engine

NOTE The 3.8L (VIN K) non-supercharged engine uses a two-piece intake manifold consisting of an upper air plenum which mounts the throttle body and a lower intake manifold assembly which houses the fuel injectors. The 3.8L (VIN 1) supercharged engine uses a similar lower intake manifold. The supercharger serves as the upper manifold.
Lower Manifold

NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold. Remove the upper intake manifold to service the lower intake.
The 3.8L (VIN 1) supercharged engine uses a manifold similar to the 3.8L (VIN K), but the supercharger serves as the upper manifold.
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Remove the upper intake manifold using the procedure above.
  4. Remove the EGR outlet pipe from the intake manifold.
  5. Detach the engine coolant temperature sensor wiring harness from the sensor.
  6. Remove the lower intake manifold bolts and carefully lift off the manifold.

To install:


0900c15280269f1b.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Lower intake manifold bolt torque sequence-3.8L (VIN K) engine
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces and between the lower manifold and the cylinder heads..
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Apply thread-locking compound to the bolt threads. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 11 ft. lbs. (15 Nm). Follow the toque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Upper Intake Manifold (Plenum)
  1. Disconnect the negative battery cable.
  2. On 3.8L (VIN 1) engines, remove the supercharger assembly. Please see the procedure in this section.
  3. Tag for identification, then remove the right side spark plug wires.
  4. Disconnect the ignition wires from the fuel rail.
  5. Remove the fuel rail. Please see Section 5.
  6. Remove the cable bracket from the intake manifold.
  7. Remove the throttle body.


NOTE Two bolts which fasten the lower intake manifold to the cylinder head are accessible are accessible only after the upper intake manifold is removed. These bolts are located in the right front and left rear corners of the lower intake manifold.
  1. Remove the upper intake manifold bolts and carefully lift the upper intake manifold from the engine.



0900c15280269f1c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Upper intake manifold and bolt torque sequence-3.8L (VIN K) engine
To install:
  1. Clean all parts well with degreaser, especially the gasket seal surfaces on the upper and lower manifold pieces.
  2. Install new gaskets to the cylinder heads and new seals to the engine block. Carefully lower the manifold into place. Make sure to install the two hidden bolts in the lower intake manifold. Hand start all bolts, then torque evenly to 89 inch lbs. (10 Nm). Follow the torque sequence, starting in the center, then working outwards in a circle.
  3. Install the remaining components in the reverse order of the removal process.

Sep 11, 2009 | 1999 Buick Regal

3 Answers

Starter for 2004 honda accord


Is this for a 4 or 6 cylinder engine?

If it is for the 4 cylinder, it's not that easy as the intake manifiold needs to be removed before the starter can be removed as the starter is under the intake manifold. Once the manifold is removed then it's a matter of a couple bolts and connections. It's not that quick a job.

Aug 19, 2009 | 2004 Honda Accord

1 Answer

Where is the Starter motor on the 2002 Lexus LX470


The starter for this car is located in whats called the valley of the engine. which is below the intake manifold. in order to get to starter u have to remove the intake manifold.

Parts needed:
Starter
intake manifold gasket (DO NOT REUSE OLD GASKET)

Apr 30, 2009 | Lexus LX 470 Cars & Trucks

Not finding what you are looking for?
2004 Honda Accord Logo

Related Topics:

748 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...