Question about Mitsubishi Pickup

1 Answer

Where is fuel pressure regulator located on 1995 Mitsubishi pickup truck?

Posted by on

  • vict12327 Dec 31, 2010

    Thanks very much; very helpful.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,926 Answers

Located under the intake plenum. REMOVAL & INSTALLATION
2.4L Engines

  1. Safely relieve the pressure within the fuel system.
  2. Drain the engine coolant to a level below that of the intake manifold.
  3. Remove the air intake hose, the breather hose, the wiring harness connector,the air intake pipe and the air hose.
  4. Disconnect the accelerator and kickdown cables from the throttle body.
  5. Remove the water hose from the throttle body.
  6. Unplug the vacuum hose from the fuel pressure regulator.
  7. Remove the throttle body from the intake manifold plenum
  8. Extract the gasket from the throttle body/intake manifold plenum mounting surface; a new gasket will be needed upon assembly.
  9. Remove the fuel return hose, the mounting bolt and the fuel pressure regulator from the fuel rail. The O-ring between the fuel rail and the fuel pressure regulator will need to be replaced with a new one upon assembly.
To Install:
  1. Install a new O-ring on the fuel pressure regulator and coat it lightly with clean gasoline. Install and tighten the fuel pressure regulator to fuel rail mounting bolts to 5-8 ft. lbs. (7-11 Nm)
  2. Install the fuel rail mounting bolts through the fuel return hose mounting bracket, through the fuel rail and into the intake manifold. Tighten them to 6-9 ft. lbs. (8-12 Nm).
  3. Connect the fuel return hose to the fuel return rail. Fasten it in place with the spring clip. Connect the high pressure fuel line to the fuel rail, using as new O-ring. Coat the O-ring with a little gasoline to help it seal better. Tighten the two retaining bolts to 1-2 ft. lbs. (2-3 Nm) of torque.
  4. Plug the fuel injector harness back onto the fuel injectors.
  5. Install the throttle body back onto the intake manifold plenum with a new gasket. Make sure the gasket goes onto the intake manifold plenum to throttle body opening with the gasket projection up and to the left (look straight into the intake manifold plenum opening, in other words from the passenger-side of the engine compartment). Install the throttle body mounting bolts with 11-16 ft. lbs. (15-22 Nm) of torque.
  6. Connect the vacuum hose, the water hose, the automatic transmission kickdown cable (if so equipped) and the accelerator cable. Refer to the accelerator cable adjustment procedure described earlier in this section.
  7. Connect the air hose, the air intake pipe, the breather hose and the air intake hose.
  8. Plug the wiring harness connector back into the throttle body.
  9. Fill the engine coolant system back up.
  10. The engine may turn over a few times until the fuel system pressure can be brought back up to normal. Check for any coolant or fuel leaks, repair if necessary.

Posted on Dec 31, 2010

  • GetMeOttaHere Dec 31, 2010

    Your welcome and Thanks for using Fixya.

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi . i am a mechanic,there is a mitsubishi l 200 pickup .it has a prableme ,not good runing from 3000rpm/minute,and came this code p0089 suction control valve stuck.what i can?please write me.


fuel pressure regulator
vacuum operated
on the Mitsubishi L200...vacuum operated
usually on the injector rail


The fuel pressure regulator is responsible for maintaining a steady fuel pressure.

Some vehicles have a fuel pressure built into the fuel rail assembly. Other vehicles with a returnless fuel supply,

the regulator is a part of the fuel pump module inside of the tank.



https://www.obd-codes.com/p0089

Oct 30, 2016 | Mitsubishi Cars & Trucks

1 Answer

Where is 1995 lincoln town car fuel pressure regulator located


The regulator should be right on the fuel rail on top of the intake.
Photo courtesy of autozone.com

c86c1a9a-8197-4db9-9348-6f6e3d40ba85.jpg

Apr 08, 2013 | 1995 Lincoln Town Car

2 Answers

1995 isuzu pickup wont start sometimes


Fuel Pressure Regulator is located on the fuel rail.


1. Disconnect the negative battery cable.

2. Properly relieve the fuel system pressure.

3. Remove the air cleaner outlet tube(s).

4. Remove any necessary components to access the pressure regulator.

5. Disconnect the vacuum hose from the pressure regulator.

6. Remove the pressure regulator attaching screws.

7. Remove the pressure regulator from the fuel rail.

To Install

8. Discard the O-rings on the pressure regulator and replace them with new ones.

9. Lubricate the O-rings with clean engine oil.

10. Install the regulator into the fuel rail and tighten the retaining screws.

11. Connect the vacuum hose to the regulator.

12. Install any components removed to access the regulator.

13. Install the air cleaner outlet tube(s).

14. Connect the negative battery cable.

Jul 03, 2012 | Isuzu Pickup Cars & Trucks

1 Answer

Fuel pressure regulator. Where is it?


Hi welcome to fixya. Well if you know the basics of an engine and know what the intake manifold and carburetor and or fuel injectors look like and are located, youll find this a simple task. Looking at the engine intake manifold where the fuel line comes into the fuel rail witch then disperses the fuel to the injectors, you will see a metal round diaphram looking component. That my friend is your fuel pressure regulator.

Dec 31, 2010 | 1995 Mitsubishi Mighty Max

1 Answer

Where is the fuel pressure regulator located on a 1995 geo prizm


The fuel pressure regulator. its on the end of the fuel rail. pull the vacuum hose off the regulator and look inside. If the inside of the hose is wet with fuel, the regulator is bad.

Nov 11, 2010 | 1995 Geo Prizm

2 Answers

Where is the fuel pressure regulator located on a 1995 ford aerostar?


the pressure regulator is located on the fuel rail near the injectors.it's cylindrical with a fuel line and a vacuum line attached.relieve fuel pressure,disconnect fuel & vacuum lines,un-bolt two retaining screws,or a clip on some models.pry regulator off it's mount,note 'o'ring seals.install in reverse.

Oct 16, 2009 | 1995 Ford Aerostar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...