Question about Ford Transit Connect

Open Question

2001 x reg transit. (not transit connect). The key is worn and won't open the bonnet, but will open doors/turn ignition. only 1 key for van. had no luck getting 1 cut as no key number. have been told to get a barrel out to get number off it but cant get door lock out cos its integrated into mechanism, unlike earlier transits which were piece of cake to remove. will key number be on back of ignition barrel, and if so are they easy to remove? thanks,

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Cant open bonnet of Ford Focus x reg grill operated key lock wont turn

hi i have mondeo on a 51 plate... the hood (bonnet) lock stopped working... i had to buy whole new lock from ford £40... drilled old one out not a problem but now i cant put lock kit togerther.. i have worked out all but the little round bits and spacers...
any ideas???

Posted on Jul 16, 2008

  • 1 Answer

SOURCE: Diagram of Location of a Starter Motor on Ford Transit 2002/2003

replaced starter motor 53 plate t350 90 transit van. lots of dust replaced fly wheel and clutch and sensor :speed up to 50 miles per hour and temp gauge goes up and cuts power

Posted on Dec 08, 2008

SOURCE: need a wiring diagram for a 99 ford transit

please visit www.2carpros.com ........you will get the your wiring diagram

Posted on Jul 29, 2009

  • 41 Answers

SOURCE: can you tell me code to my ford transit radio

... or publish the serial number here and some one will tell you the code. I will if I see it first

Cheers

Posted on Aug 31, 2009

  • 1 Answer

SOURCE: Cant open bonnet of Ford Focus x reg grill operated key lock wont turn

Stuck lock, bonnet won’t open ,,,
You do not need to drill holes in the grill or pay ford £200+
DIY..How?
Look into the grill at the top you will find the bottom of 6 plastic revscrews, 4 you get two via the grill slots use a chisel and cut them off, Then one either end of the grill. Place the chisel between two plastic layers, gently lift , check and cut, one each end.
With a wiggle that’s the top loose, There are two clips holding the bottom in place Put your fingers through the bottom slot in the grill, push down clip and greatly pull the grill, do both sides, It won’t come right out but your aim to loosen it., The lock is held in place in a sleeve with a plastic clips each side, you have push the barrel with a suitable item, this is to push it out of the sleeve and out of its housing, It may need a tap!!
Gently wiggle and pull the grill off

Lock
The lock is a ‘lock barrel along a shaft to a white plastic coupling’ this fits in to the ‘bonnet lock’
The security is at the coupling to bonnet lock in the form of a cross shaped plastic key
The key is fitted and held in place in the coupling, and when installed it’s fitted in to the lock, and once it’s in the lock part it will not come out, so therefore any jolt, pull, movement dislodges the plastic key from the coupling side and due to its design it will not slot back in so the lock barrel just rotates
To open you have to apply pressure on the shaft towards the left and into the coupling and turn the key in the lock barrel at the same time in a aim to get the coupling to catch the plastic key (take a few minutes) but it opens in the end if this is the fault, (alternatively remove the two bolts that hold the bonnet catch to the bonnet)
Once bonnet open remove the bonnet lock mechanism, then with draw the lock barrel, shaft, coupling, By looking in side you will understand regarding the cross key
Anyway you need to remove one of the catches from the side of the plastic key This way it will fit back in to coupling.
Reassemble
This is a brief description But the cost to me was 45 minutes, £2 for a pack of plastic rivets / screws, and I cached my bumper with the chisel £5 for a touch up stick Total £7. Well worth the time and effort

Posted on Nov 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Wiring diagram chevy van


Fixed Problem (it was my van) no power to ignition wire at starter. Replaced Ignition lock cylinder. just worn down. (Delivery van 50-60 starts a day). 160k miles.

Apr 25, 2013 | 2000 Chevrolet Express Cargo

1 Answer

I've locked my keys in my ford transit van 350 2006 can any help


You should be able to unscrew the antenna and slide it between the door and cab. If its too tight you can use a screw driver to gently pry the door open. Although this will depend on where your lock is located.

Mar 11, 2013 | Cars & Trucks

1 Answer

DOOR LOCK ON DRIVERS SIDE WONT WORK


key is manual lock and electric assisted unlock . charge the battery with red screw on fuse panel Use key to unlock turning to rear.
Place key in ignition then turn on and off 8 times leaving it in on position until it beeps approx 5 sec then press any button on the key and turn ignition off.

Mar 05, 2013 | 2012 Ford Transit Connect Cargo Van XL...

1 Answer

Ignition won't turn


tap on the housing where the key goes in a tumbler might be stuck try a different key then take the reg to the dealer and have them cut a new key by the code not tracing the old on

Apr 26, 2012 | 2001 Chrysler Voyager

2 Answers

How do i program my ford key fob 2 my transit van


1 - Unlock the doors. Put the key in the ignition, and turn from "Off" to "ACC" 8 (eight) times in under 10 seconds. The doors will lock. Leave key in the "ON" position

2 - Program the fobs by pressing any key on the fob. The doors locks will lock/unlock

3 -- Turn the key to Off. Locks will lock/unlock, and you are out of programming mode.

I bought new remote Key Fob on Ebay and it did work properly on my Ford Transit LWB 2003. Good Luck!

Mar 22, 2012 | Cars & Trucks

1 Answer

The bonnet of my ford transit van wont open with the keys, how could i open it?


Take grill off, put your hand up the inside on the grill
, which you will access the release button fo the first part.

Then use your key to release the second part.

Mar 22, 2010 | Ford Taurus Cars & Trucks

2 Answers

Where is central locking relay found on kangoo van w reg


Either with the fuses, or under the bonnet near to the bulkhead, possibly passenger side

Jan 04, 2010 | 2000 Renault 181

1 Answer

Bonnet will not open with key


Not sure if the solution can be applied to 2006 focus, I have an European Mk2 Focus which also having the same problem. Here is what you can try.

To Open:
1. Jack up the car on the lifter.
2. Open bottom engine cover.
3. Loosen two (10mm) screws which secure the bonnet lock assembly. The screws located between air manifold and radiator.
4. Once the screws released, disconnect the alarm cable/socket connected to the lock assembly.
5. Try pull open the bonnet, it may require little force to pull the bonnet open due to a little white plastic link (~1" long, plus (+)shaped) is still connected between the lock assy. and cable assy. Failure to release bonnet lock is only caused by this plastic link!
6. Once the bonnet opened, the cable assy can be detached by pulling it from engine side out. Inspect the plastic link if it worn out.

To Install:
1. Attach lock and cable assy. Ensure the plastic link is properly inserted in its place between lock and cable assy. Test the mechanism with the car key.
2. Insert the whole assembly from engine side out.
3. Secure with two 10mm screws, reconnect alarm cable.
4. Reinstall bottom engine cover.

Hope this help. Sorry for my English.

Oct 31, 2009 | 2006 Ford Focus

1 Answer

Constant beeping when opening door to exit van


Good news. After letting the van sit for a few hours, when I went to get in it again, I opened the van with the key (ie. not the remote fob) and there was no beeping. I don't know if checking all the fuses (I fulled and checked each one), or disconnecting the battery, using the key, or just letting it sit did the trick, but it is now fixed.

Oct 02, 2009 | 2001 Oldsmobile Silhouette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...