Question about 2002 Jaguar X-Type

1 Answer

Thank you for your response , been going crazy here...got panel off enough to put hand in but don't know where to pull to unlock door.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jaguar Master
  • 17,970 Answers


Jaguar 2000-06 - Locks & Lock Systems
Power Door Locks - Removal & Installation

Door Lock Switch
Door Lock Diagnosis & Testing

  1. Visually inspect the following:
    Misaligned door(s), hood or luggage compartment lid Door latches Actuating rod Exterior door handle Interior door handle Door lock cylinder Cable Luggage compartment lid exterior release switch Fuse(s) Wiring harness Electrical connector Door lock actuator Remote transmitter batteries Vehicle battery Remote transmitter Door lock switch Front electronic module
  2. If an obvious cause for an observed or reported concern is found, correct the cause (if possible) before proceeding to the next step.

Door Lock Motor
Coupe And Convertible
  1. Turn ignition key to position II.
  2. Motor door glass to fully raised position.
  3. Turn ignition key to position O.
  4. Disconnect the negative battery cable.
  5. Remove door casing for access.
  6. Remove door water shedder.
  7. Position PVC secondary water shedder for access.
  8. Slacken and remove the door glass rear runner lower securing screws.
  9. Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
  10. Slacken and remove the upper securing screw and move the runner away from the glass.
  11. Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
  12. Slacken and remove the three latch assembly securing screws and position latch for access.
  13. Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
  14. Release operating cable from door handle. Move inner door handle to the locked position. Remove operating cable outer abutment from support bracket. Disconnect cable inner from door inner handle.
  15. Remove lock motor assembly from door.
  16. To install, reverse removal procedure.

    Thank you for your response , been going crazy - zjlimited_378.jpg

    Fig. Removing door lock actuator


Sedan
  1. Remove the door window glass
  2. Detach the interior door handle.
  3. Detach the actuator remote cable from the interior door handle.
  4. Remove the interior door handle.
  5. Detach the door window glass run.
  6. Remove the exterior door handle retaining screws.
  7. Remove the front door actuator retaining screws.
  8. Reposition the front door actuator and exterior handle.
  9. Remove the front door actuator and exterior handle.
  10. Disconnect the front door actuator remote cable.
  11. Detach the door lock cylinder connecting rod (1).
  12. Detach the exterior door handle connecting rod (2).
  13. Remove the front door actuator (3).
  14. To install, reverse removal procedure.

    zjlimited_379.jpg

    Fig. Removing door lock motor-Sedan



Hope this helps.

Posted on Dec 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the front passenger accuator.which works fine.the door unlocks and locks with the remote.when i shut the door it wont open.you can feel the cable pulling slightly but not enough to disengag


Hey Trent once ya gain access to it again go where the metal tab is that holds the cable in place and simply give it a little tweak with a pair of pliers pulling it so it stretches the cable slightly and then test it and im sure ya know now but never put the panel on till ya test it.
good luck n hope this helps. Geo

Dec 05, 2013 | Chevrolet Tahoe Cars & Trucks

1 Answer

I replaced the power lock switch on the driver side of my chevy malibu because the locks were locking and unlocking by themselves, I also heard a beep under the dash. The problem was taken care of. Now...


All the lock's ,were locking an unlocking or just the driver door lock ? Probably wasn't the switch ,more likely a bad input to the BCM . The door lock's are computer controlled .
Do you know what a BCM is ? body control module .
Each door lock switch is wired to the body control module (BCM) through a separate door lock/unlock signal circuit. While these circuits are separated between the BCM and respective door lock switch, they are connected into a single circuit within the BCM. The BCM supplies voltage through the door lock/unlock signal circuits to each door lock switch. When either door lock switch is operated, this supply voltage is pulled to ground, providing the BCM with the required lock or unlock signal. In order for the BCM to distinguish between a lock and unlock signal, the lock switch contains two separate paths for this voltage to flow to the same body ground. When the switch is operated to the unlock position, the supply voltage flows to ground through a 1.5 K? resistor. When the switch is operated to the lock position, the supply voltage flows to ground through a different part of the switch circuit, which has no resistor. The BCM then interprets the flow of voltage as a lock or unlock request and powers the door lock actuators to the appropriate lock or unlock position.


Door Locks Go Crazy 1
Door Locks Go Crazy 2
Door Locks Go Crazy 3


Dec 19, 2017 | 2008 Chevrolet Malibu LT

1 Answer

1998 Dodge ram van 3500 door will not open. power locks that cick on for open & close don't work


Not easy to find, incorporated in the lock itself, usually a little tag sticking out to pull/push, but it is normally on the side you can't get too, I take the lock out complete and then you know what you are working with, you can see how it all works that way!!

Mar 06, 2018 | Cars & Trucks

2 Answers

Toyota Celica 2000 GTS hatch won't unlock


Go inside the rear hatch area remove the trim panel and manually trip the hatch release.

Jul 26, 2012 | 2000 Toyota Celica

1 Answer

2002 Suburban 1500. Driver's side power door lock, the actuator does not move the rod to lock or unlock - must do it manually. The rest of the power locks are working, and I can hear the actuator in the...


I have struck silimar issues with fords in NZ. If the actuator is getting full voltage during lock and unlocking, the actuator is faulty. Even though it wants to go it does not have enough strength to pull the lock mechanism, so it can not lock or unlock the catch.

Oct 11, 2010 | 2002 Chevrolet Suburban

2 Answers

Sunburn 1994 handle wont work


Yes, Usually If you pull inside the lock area incorrectly, it will cause the rod to detach from the door latch. The door panel will have to come off and the rod, located and reattached. The retaining clip probably is damaged so inspect it and you should be able to find a replacement at NAPA or local dealership.

May 30, 2009 | 1994 Pontiac Sunbird

1 Answer

2003 ford windstar - power locks only open drivers door


yes it is the door lock switch in the door trim panel it should pop out from the back to forward / Please rate my response thank you very much

Jan 18, 2009 | 2003 Ford Windstar

1 Answer

Door panel removal


  There is hidden screw under top of arm rest.  the mirror control comes out.  Be careful.  then there are 2 screws in bottom of arm rest.  Then the arm rest/handle needs to spin up towards sky and it will pull out.  the scushing (plastic around handle ) slides forward and this handle surround will come off.  Then there are clips that are behind panel.  Put hand between door and door panel and pull panel outward. be careful.  sometimes firm tug is better

Jan 01, 2009 | 2001 BMW 325

2 Answers

PT CRUISER


look for the edges around the radio get a thin putty knife seperate the panel from the rest it should just pop out/ as you put the putty knife you will know where the push in retainers are again just pull out/ Please rate my response Thank you very much

Dec 30, 2008 | 2006 Chrysler PT Cruiser

Not finding what you are looking for?
2002 Jaguar X-Type Logo

1,307 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

79847 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...