Question about 1996 Honda Civic

2 Answers

Muffler i cant get the screws to go back in were the muffler connects is it bacause of putting the gasket in wrong. the springs are to giving me problems.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 26 Answers

Take the exhaust from that point all the way to the back off the brackets. Connect your exhaust and then re hang it back on the hooks. This is the same way an exhaust shop will do it and you will save about a hundred bucks not taking it to them. I had the same problem with my civic the dc headers did not want to connect to my converter this is what i did and it all went together like butter.

Posted on Jul 21, 2008

No i think that you should try get a professional for that if you do it, it sound like it's right but it's not which will lead to excessive engine vibrations which in turn could lead to rapid wear of engine brackets.

Posted on Jul 08, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I my JD 757 developed hole in muffler. Replaced this spring. Is still pretty loud. What else could be wrong. Gasket? I did tighten two muffler attachments at the engine


Check everything from the exhaust manifold back, Use water pump channel locks to squeeze the pipe every few inches to see if it is weak,

Apr 14, 2016 | Cars & Trucks

1 Answer

How to remove catalytic converter


There should be a flange type of piece with a donut type of gasket seal. If this is the case you would need to tap those outward to break the seal. use a hammer with a screw driver to do this or what ever else might work for you. You might have to loosen the muffler pipe and move it away so it will let the flange separate. As for the other idea of it being welded, only if it wasn't bolted on would it be. I'm not a expert but i do hoe this helped give you something to work with. Last resort would be to take it in to a muffler shop. good luck with that.

Nov 26, 2014 | 2006 Pontiac G6 GTP

2 Answers

HI Guys This problem is continued from the other


you need to set the idle pin. there is a stopper on the throttle you need to screw it back. as it has never been used therefore it has never been set. screw it back until it is at the right revs then lock it off.

Oct 16, 2013 | 1966 Ford Mustang

1 Answer

Can't find the right gasket


You may have this posted in the wrong product category. Please select another category appropriate to the problem and re-post the problem so the correct expert will see and respond to the question..
This is for car and truck problems related to factory installed systems not add on aftermarket systems.
This post can't be removed or moved, please re-post the question in the correct product category. Thanks

Oct 25, 2012 | Cars & Trucks

1 Answer

How to install mufflers on a 2011 super glide


I'm sorry but you have this posted in the wrong product category. Please re-post the question in the proper category This is the car and truck problem category






Jun 29, 2012 | Cars & Trucks

1 Answer

Difficult to start up sounds sluggish, once shut off, won't start, coil was hot (coil recently replaced). Needs new muffler.


Replace spark plugs with new ones. put new muffler in. The muffler has an affect on the way engine runs. (back pressure) is needed. At this age you may need a head gasket(s). Compression check on all cylinders. The list goes on... Good luck

Jun 10, 2011 | 1982 Ford F 250

1 Answer

Loud muffler sound is it the muffler


It can be the muffler. Also the Catalytic converter or just a gasket connecting the exhaust manifold to the pipes.

This needs to be inspected because fumes can kill. The entire system is meant to get the fumes to the back bumper through the pipes.

May 21, 2010 | 1996 Ford Windstar

2 Answers

Hello I just replace my motor mounts had to pull muffler from motor put back and it sounds loud so i took it off went to auto zone and the clerk said i needed the donut so after i drilled out the busted...


sounds like the manifold gasket is bad, or the exhaust pipe coming from the manifold head was not properly seated. Got back to auto zone and get a repair/maintence manual for your car , and it should help you get the manifold head gasket/muffler assembly back together.

Jul 12, 2009 | Cadillac Eldorado Cars & Trucks

2 Answers

I need to replace the oil pan gasket and it looks like the exhaust pipe is in the way-what should I do?


The tail pipe is connected to the muffler. You need to remove the entire muffler. However, the hot exhaust fumes tend to corrode connections so taking off the muffler might require some work.

Jul 02, 2009 | Toyota Camry Cars & Trucks

1 Answer

Rough idle


some times , the egr valve will hang from carbon causing it sound like ahole in the muffler when snap the throtel try tapping the egr vavle with the plastic end of screw driver or remove the egr and clean out the carbon and replace the gasket

Jan 09, 2009 | 1994 Pontiac Grand Prix

Not finding what you are looking for?
1996 Honda Civic Logo

Related Topics:

88 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...