Question about Dodge Ram 1500

1 Answer

How do you change the spark plugs in the 3.7 litter v6 and do i half to change the coil pacs to

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 480 Answers

Change your spark plugs one at a time and make sure to gap them you can get a gaping tool at a auto parts store the plugs do already come pregapped but its always a good idea to check the gap before installing. you almost never have to replace the coil packs unless there is a problem with them.

Posted on Dec 31, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I change the spark plugs on my 2007 Kia rondo lx v6

1. Remove the ignition coil connector (A).
2. Remove the ignition coil.
3. Using a spark plug socket, remove the spark plug.26379325-trdzh3npzosxk4r5ena25aw0-5-0.jpg

Nov 30, 2016 | 2007 Kia Rondo LX V6

1 Answer

How to I change coil pac on a 04 Nissan Quest

You don't have a coil pack, it appears you have coil on plug ignition, One coil for each spark plug.


Sep 19, 2016 | 2004 Nissan Quest

1 Answer

Computer readout says misfire on #1 and #5 cyl what would fix this?

It is 12 years old, most of its litter mates are already upside down in junkyards useful only for donating used parts. If it has spark plug wires, change them AND the plugs. Use a good set of wires, not a generic set of wires for any V6. You may end up at a FMC dealer for plug wires. If it does not have plug wires then you should get the many dedicated coils tested via a dealer computer diagnostic.

Jul 13, 2011 | 1999 Lincoln Town Car

3 Answers

How do you change spark plugs in a 2004 hyundia sonata

It depends on which engine is in the vehicle. The 2004 Sonata came with two possible powertrains -- the 2.4 Lit L4, and the 2.7 Lit V6.

On the 4 cylinder engine, there are two coil packs and two ignition wires, Below each coil pack is a spark plug (#2 and #4 cylinders). The wire from # 2 coil pack goes to #3 spark plug, and the wire from #4 coil pack goes to #1 spark plug.


Now the 2.7 Lit V6 requires you remove the surge tank (intake manifold) in order to access the spark plugs & wires on Bank 1 (Right Hand side of the engine).


Jun 10, 2011 | Hyundai Sonata Cars & Trucks

2 Answers

No spark #4 cylinder replaced coil pack and plug still no spark where should i go next ford 2001 v10 motor

Hello there:
if you have replaced the coil pac you may want to remove it again and make sure there is no moisture or corrosion then if and still have nothing check the crank sensor and the ignition module i just replaced mine after several weeks of troubleshooting and now it is fine
and finally and hopefully this is not your problem is the ecu or electronic controle unit this is the first line of the ignition system and the most important it tells the coil pac to fire and tells which one to fire and when this can have part of it be bad and still have other coil pacs to fire ok

Aug 16, 2010 | Ford F-250 Cars & Trucks

1 Answer

Still running rough after plugs and wires.

if the other coils are functioning, then voltage to the coil pack is ok. removing the spark plug wire from the suspected bad coil with no change in engine performance is a reliable procedure to check for a bad coil.

May 11, 2010 | 1991 Buick Park Avenue

1 Answer

How to change spark plugs on the v6 Nissan 2000 Maxima?

For the 3 spark plugs in front:
1. You would have to remove the plastic protective cover (this cover is silver&red w/ the words "nissan and v6 3000")
2. unplug connector and remove coil (DO NOT mix up the coils, keep the same coils on the same cylinder)
3. Remove spark plug

Rear 3 plugs: located on the rear of the intake (the black pipes atop the engine). there are 3 openings at the rear of the black intake pipes, each opening has a coil mounted.
1. Unplug coil connector and remove coil
2. remove spark plug (you'll need a long extension)
***Installation is reverse, be sure not to over tighten the plugs!! Use anti-seize compound on all the new plugs threading. Hopefully this helps!!

Apr 01, 2010 | 2000 Nissan Maxima

1 Answer

I am changing the spark plugs and wanted to know where are they located.

There are individual coil pacs bolted to the valve covers with either 8mm or 10mm bolts. unplug the connector and remove the coil pac. It is located under that coil. THis is called direct ingnition.

hope this helped.
go to

for a picture.

Nov 21, 2009 | 2004 Chevrolet TrailBlazer

2 Answers

I cant find my distributer on my 1988 pontiac grand am. where is it?

there is none,it has coil packs and a crank sensor,they are behind the rear of the motor near the firewall down low,and a pain in the *** to change,

Oct 30, 2009 | 1988 Pontiac Grand Am

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

79847 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides