Question about 2008 Jeep Wrangler

1 Answer

On2nd clutch 08 wrangler 1st one replaced @ 9000 mi.s throw out bearing makes noise again

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 220 Answers

I hope when the first clutch was replaced the throw out bearing was replaced. It sounds like you are either riding the clutch (foot resting on clutch pedal and partially depressing the clutch during normal driving) or the adjustment is incorrect. The throwout bearing should not contact the pressure plate unless the clutch pedal is depressed when adjusted correctly. The constant contact is what wears the bearing out prematurely.

Posted on Dec 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Metal on metal noise


hi,

most likely the throw out bearing is at fault. when you push the clutch a spinning bearing pushes the clutch plate away from the flywheel disengaging trans so you can switch gears. the transmission has to come away from the engine to fix it.

jm

Jul 04, 2017 | Toyota Corolla Cars & Trucks

3 Answers

Hi my rx8 is makin a grinding noise from the gearbox and the noise goes away wen foot is pressed on the clutch makes a noise wen drivin in 1st 2nd 3rd n 4th gear noise goes in 5th and the noise is there in...


What?! Really! The noise goes when the clutch pedal is depressed! So the noise goes when the release bearing (throw-out bearing) is engage? So how would that be a release bearing/clutch problem? If it didn't make a noise until the clutch pedal was depressed, it would be the release bearing! In other words its the input shaft bearing and/or counter shaft bearing in the gearbox. Stop giving people bad advice

Mar 11, 2011 | 2004 Mazda RX-8

1 Answer

Have got a 1997 saab 9000 cs hatchback.When I put my foot on the clutch it makes a whirring noise.Dissapears when clutch not engaged. Any ideas? Theres also a strange rubber smell after being driven for 30...


Throw out bearing is going bad. When you depress the pedal it makes contact with a bearing that contacts the clutch fingers. Bearing is shot. Continue running this way and the pressure plate will be ruined.

Dec 30, 2010 | 1997 Saab 9000

1 Answer

I replaced my clutch and throwout barring from the clutch kit. I didn't turn the fly wheel. And the pilot barring didn't go with my model car. So I didn't use it. The car is now put back together, and it...


3 quarts should be enough fluid. Did it make the noise before you replaced the clutch. It sounds like a bearing in the trans. It's not the pilot bearing. A pilot bearing would make noise when you step on the clutch and then the noise would go away when you let out the clutch. Can you describe the noise? It sounds like a bearing in the trans or a problem with the throw out bearing.

Oct 30, 2010 | 2000 Mitsubishi Mirage

1 Answer

Have a 2004 jeep wrangler x with a manual transmission and when it is in nutral and the clutch out it rattles. Is this normal? i still have the factory warranty and went to a chrysler dealer and they tried...


A rattling noise from the transmission is never a normal condition no matter what anyone says, and the first thing to do is to check the transmission fluid level, but it sounds to me like the throw-out/release bearing is riding the clutch pressure plate, and when the clutch pedal is in the up position the throw-out/release bearing and the clutch pressure plate should not be touching each other, and the only time that they should make contact is to release the clutch disk in order to shift the transmission into gear. There should be about 1 to 2 inches of free play in the clutch pedal, and the clutch should start to grab within 1 to 2 inches of letting the clutch pedal up off of the floor, and if this is not the case you might need to have the clutch properly adjusted especially if the clutch does not start to grab until the clutch pedal is half way up from the floor. Also, the main bearing in the transmission could be going out due to low fluid, or a damaged pilot bearing that is allowing the transmission input shaft to wobble just enough to cause a rattle from the main bearing or even a vibration in the transmission.

Jun 02, 2010 | 2004 Jeep Wrangler

2 Answers

The clutch slips in first gear when it is hot.


You need a new clutch again. Sorry to give ya the bad news. This time make sure they put a new transmission seal in so fluid can not leak onto the clutch plate and ruin it.

Apr 25, 2010 | 1999 Jeep Wrangler

1 Answer

97 jeep wrangler sport, mechanic changes clutch


If the pilot bearing was the problem it would make noise with the clutch pushed and go away when you let it out. Have you checked the fluid level in the transmission?

Apr 03, 2010 | 1997 Jeep Wrangler

1 Answer

I have a 90 jeep wrangler, 4cyl and 5 speed transmission, when i accelerate in any of the gears, it makes a popping noise and the second it makes that noise it seems like the jeep stops pulling, if you...


It sounds like it is the throw out bearing. From your description of the vehicle not pulling its weight, it is going to need a clutch. The throw out bearing will come in most clutch kits, so when you replace the clutch you can replace the throw out bearing, pressure plate, and pilot bushing.

Oct 18, 2009 | 1990 Jeep Wrangler

2 Answers

2008 Jeep Wrangler Throw-Out Bearing Squeal


If there is a service bulletin or recall involved, some consideration will be given to that . Dealers will run a recall check on their computer and give you a printout if you ask for it. If no recalls etc, likely you will pay entire bill.

Feb 27, 2009 | 2008 Jeep Wrangler

2 Answers

Second tinme throw out bearing has to be replaced.


This is a weird one. Unless there is a TSB on bad bearings from the dealer, the only thing I could GUESS is a bad pressure plate, but you said you are replacing the whole thing.

Nov 22, 2008 | 2008 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...