Question about Mercedes-Benz S-Class

1 Answer

Locating the thermostat on vehicle - S-Class Mercedes-Benz Cars & Trucks

Posted by on

  • Mark Freedman
    Mark Freedman Dec 31, 2010

    Can you tell me the Model of Mercedes and the Year. Thanks, Mark

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 520 Answers

On most vehicles you follow the upper radiator hose back to the engine and there it is

Posted on Dec 31, 2010

Testimonial: "very well put thanks"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

NOW WHERE IS THAT THERMOSTAT?????? ALL VEHICLES


Ok, we get asked this allot, "where is my thermostat located" well here is a simple way to find it, this is on all vehicles that have a thermostat, not just cars....Locate the top or bottom hose on the radiator, follow the hose to the Engine/Motor there you will find a little housing, and under that housing is the thermostat....simple's

on Oct 11, 2010 | BMW 525 Cars & Trucks

1 Answer

Location of thermostat


Open the hood and find the radiator.
Get help and a flashlight if you need to.
The radiator should have two black hoses attached to it, one on top and one on the bottom.
Those hoses are about 2 inches in diameter, maybe a little larger.
On cars made up to about 1985, the thermostat was found at the engine end of the top radiator hose.
There would have been a bell-shaped housing with the thermostat inside.
These were usually rear wheel drive vehicles.
Cars made since the mid-80's and particularly front wheel drive vehicles have the the thermostat located at the engine end of the lower radiator hose.

Jan 19, 2013 | Cars & Trucks

1 Answer

Hi im trying to find out if my grand prix has a thermostat .not sure if it does i thought maybe it might be built in


all vehicles have thermostats, the location differs from vehicle to vehicle, looking up the information specific to your car will help, using the internet or shop manuals to find the year of car, engine, transmission, and then finding an exploded diagram of your motor will help you find the thermostat on your car, but be careful, some thermostats are very hard to replace

Mar 01, 2011 | 1998 Pontiac Grand Prix

2 Answers

Where is the thermostat located on a 2005 jeep liberty 3.7


zjlimited_550.jpg

Fig. The location of the thermostat and its housing on the 3.7L engine
  1. Disconnect negative battery cable at battery.
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Remove splash shield.
  5. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  6. Remove thermostat housing mounting bolts, thermostat housing and thermostat .

Hope this helps (remember to rate thisd answer).

Jan 25, 2011 | 2005 Jeep Liberty

1 Answer

Please tell me where locate the theromostat in


The thermostat is located inside the thermostat housing. To find it follow the upper radiator hose to the engine block.
Depending what size of engine you have the location is different.
The thermostat on this vehicle's (the Envoy & Trailblazer are essentially the same vehicle) In-line 6 cylinder engine is on the driver's side of the engine, below & behind the alternator.
If you have a V8 cylinder engine is in front of engine see the picture. Item 303 thermostat housing, 305 thermostat, and 304 thermostat gasket.
global1207.gif

Nov 06, 2010 | 2004 GMC Envoy

1 Answer

Need location of thermostate


Removal & Installation 3.9L, 5.2L & 5.9L Engines To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Coolant until level is below thermostat dod_trk_altbracket.gif

    • Support bracket located near rear of alternator (A/C Vehicles) dod_trk_releasebelttension.gif

    • Alternator drive belt by attaching a wrench to the pulley mounting bolt of the automatic tensioner, rotating the tensioner clockwise to release belt tension, and removing the belt:
    • Alternator mounting bolts, but do not remove any wiring at alternator
    • 4WD indicator lamp wiring harness (4WD vehicles)
    • Alternator and position aside WARNING
      When servicing constant tension hose clamps, use only tools designed for servicing this type of clamp, such as special clamp tool (number 6094). Always wear safety glasses when servicing constant tension clamps. Always replace constant tension clamps with the same numbered clamp.
    • Radiator hose clamp and upper radiator hose at thermostat housing and position wiring harness aside to gain access to thermostat dod_trk_59l_thermostat.gif

    • Thermostat housing mounting bolts, thermostat housing, gasket and thermostat
To Install:
  1. Clean intake manifold and thermostat housing mating surfaces.
  2. Install or connect the following:
    • Thermostat (spring side down) into recessed machined groove on intake manifold
    • Gasket on intake manifold and over thermostat dod_trk_thermohousingposition.gif

    • Thermostat housing to intake manifold NOTE: The word FRONT is stamped on housing and must be placed towards front of vehicle.
    • Housing-to-intake manifold bolts.
      1. Torque to: 200 inch lbs. (23 Nm)
    • Upper radiator hose to thermostat housing dod_trk_drivebeltrouting.gif

    • Alternator (A/C Vehicles)
      1. Torque to: 30 ft. lbs. (41 Nm)
    • Support bracket
      1. Torque to: 40 ft. lbs. (54 Nm)
    • Drive belt over all pulleys except idler pulley
    • Socket/wrench to pulley mounting bolt of automatic tensioner and rotate clockwise
    • Belt over idler pulley, let tensioner rotate back into place and remove wrench
    • Coolant
    • Negative battery cable
  3. Start and warm the engine and check for leaks.
4.7L Engine To Remove:
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Coolant
  3. Safely raise and support the vehicle.
  4. Remove or disconnect the following:
    • Splash shield
    • Lower radiator hose clamp and lower radiator hose at thermostat housing 4.7L engine shown 3.7L similar chry_47_thermostst.gif

    • Thermostat housing mounting bolts, thermostat housing and thermostat
To Install:
  1. Clean timing chain cover and thermostat housing mating surfaces.
  2. Install or connect the following:
    • Thermostat (spring side down) into recessed machined groove on timing chain cover
    • Thermostat housing on timing chain cover
    • Housing-to-timing chain cover bolts.
      1. Torque to: 112 inch lbs. (13 Nm)
    • Lower radiator hose on thermostat housing
    • Splash shield
  3. Lower vehicle.
  4. Fill cooling system.
  5. Connect negative battery cable to battery.
  6. Start the engine and check for leaks.
prev.gif next.gif

Aug 26, 2010 | 2001 Dodge Durango

2 Answers

Where is the thermostat located


77f1c56.jpg

Fig. The location of the thermostat and its housing on the 3.7L engine

  1. Disconnect negative battery cable at battery.
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Remove splash shield.
  5. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  6. Remove thermostat housing mounting bolts, thermostat housing and thermostat .
To install:
  1. Clean mating areas of timing chain cover and thermostat housing.
  2. Install thermostat (spring side down) into recessed machined groove on housing assembly. Make sure rubber seal locating tab is positioned in the corresponding notch in the housing.
  3. Position thermostat housing on timing chain cover.
  4. Install two housing-to-timing chain cover bolts. Tighten bolts to 105 inch lbs. (12 Nm) torque.
  5. Install lower radiator hose on thermostat housing.
  6. Install splash shield.
  7. Lower vehicle.
  8. Fill cooling system.
  9. Connect negative battery cable to battery.
  10. Start and warm the engine. Check for leaks.

Hope helps (remember rated and comment this).

Aug 06, 2010 | 2002 Jeep Liberty

1 Answer

CHANGE THERSTAT ON 2002 JEEP LIBERTY


3.7L Engine - Thermostat
  1. Disconnect negative battery cable at battery.
  2. Drain cooling system.
  3. Raise vehicle on hoist.
  4. Remove splash shield.
  5. Remove lower radiator hose clamp and lower radiator hose at thermostat housing.
  6. Remove thermostat housing mounting bolts, thermostat housing and thermostat .

    a105ca1.jpg
    Fig. The location of the thermostat and its housing on the 3.7L engine (click for zoom)
To install:
  1. Clean mating areas of timing chain cover and thermostat housing.
  2. Install thermostat (spring side down) into recessed machined groove on housing assembly. Make sure rubber seal locating tab is positioned in the corresponding notch in the housing.
  3. Position thermostat housing on timing chain cover.
  4. Install two housing-to-timing chain cover bolts. Tighten bolts to 105 inch lbs. (12 Nm) torque.
  5. Install lower radiator hose on thermostat housing.
  6. Install splash shield.
  7. Lower vehicle.
  8. Fill cooling system.
  9. Connect negative battery cable to battery.
  10. Start and warm the engine. Check for leaks.

Hope helps (remember rated this).

Aug 04, 2010 | Jeep Liberty Cars & Trucks

4 Answers

Where is the thermostat for 1995 toyota camry v6 located


the thermostat is located driver's side of the vehicle. Follow the upper radiator hose to its end to a water outlet housing. the thermostat is in the outlet. take off the air flter lid and hose and it is easier to get to. take the hose off and the metal line to the housing. the other part of the housing is holding the thermostat. it is held with two 10 mm bolts. good luck.

Sep 06, 2008 | 1995 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

yadayada
yadayada

Level 3 Expert

76649 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...