Question about 1993 Mercury Villager

1 Answer

1993 mercury villager when diriving at speeds over 50 car will lose power and you have to play with gas peddle to get speed back up, than car will be ok for short time and do it again

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercury Master
  • 4,369 Answers

Clean the MAF sensor with carb cleaner first. It's in the air intake tube, spray the tiny wires inside with carb cleaner to get varnish off heated wire. Do not touch or move them.


Gerry

http://groups.yahoo.com/group/villagerquest/

Posted on Jan 08, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When pressing on the accelerator my safari bogs down and starts to lose power.


Sounds like the accelerator linkage or kick down band of the transmission need adjustment.

Mar 23, 2015 | 1998 GMC Safari

1 Answer

I have mercury villager 1999 ,when started in morning idler ok , after run for 20 mnts engine stall in idler turn off ,end stared back up ok give gas go normal , and star again idler low like lose power...


Read the following and follow the instructions for this problem.

Here are the most common causes of idle surge, stalls at stops, slow idle speed, erratic idle speed, rough idle and engine hesitation (and other problems), it is in most cases the idle speed control air-bypass valve and or throttle valve and upper intake, these area's get full of gunk and combustion residue over the miles and cause idle issues (stalls, low idle) like yours, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake

Sep 28, 2017 | 1999 Mercury Villager

1 Answer

What is the correct idle speed for a 1996 mercury villager


50-750 rpms

yahoo group for villager quest owners for more help

Oct 17, 2011 | 1996 Mercury Villager

1 Answer

Where is the speed sensor located on a 1993 mercury villager and how do you fix it?


it's on the top reear of trans. often hard to pry out. 10 mm bolt, two pin connecotr. what is issue?

go here

http://groups.yahoo.com/group/villagerquest/

Nov 11, 2010 | 1993 Mercury Villager

2 Answers

93 mercury villager check engin light comes on for 2 days then off for a day then back on i dont know where to plug in my scanner


I too have a 93 Villager. Recently the check engine light came on especially on the highway cruising speed and it turned out to be caused by clugged EGR. My mechanic cleaned up the carbon build-up ( not replace EGR) from all those 170K miles and it seems to fix the problem. He charged me $150 for the labor only. Also the gas mileage seems to improved a bit as well.

Oct 27, 2009 | 1993 Mercury Villager

1 Answer

Lose of power on acceleration like its starving


Sounds like there is a load of dirty fuel in that gas tank. Ran good for a while after changing fuel filter, then began to run poorly again. Remove fuel tank, drain and clean out, replace fuel filter AGAIN. That should cure it. Hope this helps

Jun 18, 2009 | 1993 Mercury Villager

1 Answer

How do you remove a stuck speed sensor?


very difficult. They corrode in place due to steel contacting aluminum.

Soak base with penetrating oil. Tap steel base on side with chisel to break it loose. Try to get vice grip on base and tap back and forth to twist it back and forth to free up. It takes a lot of effort and time.

go here too.


http://groups.yahoo.com/group/villagerquest/

Apr 23, 2009 | 1993 Mercury Villager

Not finding what you are looking for?
1993 Mercury Villager Logo

Related Topics:

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

80668 Answers

fordexpert

Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...