Question about Chevrolet K2500

1 Answer

I bleed clutch hydraulic system and now the pedal is so hard i cant push it at all

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,165 Answers

While you were bleeding the clutch, did you maintain the the hydraulic fluid level? It sounds like it ran out of fluid.

Posted on Dec 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On occasion now more often the clutch when I push it down it stops and gets hard not allowing me to change gears.


hydraulic operation , bleed the system , check reservoir level, replace master cylinder
for cable clutch operation , replace the cable
the problem is that the clutch pressure plate is not fully disengaging when the clutch pedal is depressed and the problem is not in the clutch but the pedal operation

Sep 27, 2016 | 2003 Saturn VUE

2 Answers

Does Toyota hilux R150 gear box have a clutch adjustment ?ie master cylinder adjustment ?


If it is adjustable it will have a threaded push rod at the slave cyl ,bleed the hydraulic system first adult the clutch then bleed again .

Oct 26, 2015 | Toyota Cars & Trucks

1 Answer

Bleed clutch hydraulic system John Deer 4300 Tractor - year 1998


two of you needed here ,put a big screwdriver into the operating arm and pull it back so the piston goes in ,slacken bleed nipple then helper pushes clutch down -hold it down then tighten nipple .repeat a few times and you will feel pressure on the clutch arm ,now get helper to push pedal down and hold it down ,pull bar to push piston in as it moves you open nipple then close it after a squirt of air comes out and repeat this a few times and it should have a hard pedal

Dec 06, 2014 | Cars & Trucks

2 Answers

88 Bronco 2 4x4 2.9L has air in the hydraulic clutch line. I have been pumping the pedal and bleeding it for hours, including cracking the bleed screw with the pedal depressed. nothing seems to work.


Try to find where the air is entering the clutch line. When you bleed the cylinder you cannot drain the reservoir completely when bleeding. If you do then you'll only pump more air into the system.

Oct 29, 2014 | 1988 Ford Bronco II

1 Answer

Bleed hydraulic clutch


there will be a bleed nipple on the clutch slave cylinder ,when bleeding same process as brake bleeding but push the padal VERY slowly as could push piston past usual use point and then the rubber seals may pull from piston

Mar 30, 2014 | 1998 Saab 900

1 Answer

Clutch pedal goes to floor and half works on my b2200 1987 mazda pick-up


If the clutch is hydraulic operated, you need to bleed the clutch at the slave cylinder, down on the transmission housing. Bleed it just like you bleed brakes of air in the line-open bleeder valve, someone pushes clutch pedal slowly to floor, close valve, and repeat until fluid comes out valve in a steady stream. Make sure the clutch reservoir is full before starting. It uses regular brake fluid.
If not hydraulic, it would be cable operated. Adjust the cable until clutch pedal is right.

Dec 29, 2012 | Cars & Trucks

1 Answer

My clutch is not angaging need to see how can i bleed


Hydraulic Clutch System BLEEDING The clutch system can be bled using a pressure bleeder. Follow the instructions that come with the pressure bleeder for the proper pressure bleeding procedure. The maximum line pressure while pressure bleeding must not exceed 36 psi (248 kPa). NOTE: To bleed a clutch manually requires the assistance of a second person, a section of hose that is compatible with brake fluid (preferably clear) and fits the slave cylinder bleed screw snugly and a container to catch the fluid that is bled through the system. As brake hydraulic fluid easily absorbs moisture, always use fresh fluid when bleeding a hydraulic system.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. To bleed the system perform the following:
    1. Top off the hydraulic fluid reservoir using a fluid that meets the standards of the vehicle's hydraulic system.
    2. Open the clutch slave cylinder bleed screw and press the clutch pedal to the floor and hold the pedal down.
    3. Close the clutch slave cylinder bleed screw.
    4. Release the clutch pedal.
    5. Check the hydraulic fluid level and top off as necessary.
  3. Repeat the above steps until the discharged fluid is clean and no air bubbles appear during the bleeding process.
prev.gif next.gif

Aug 03, 2010 | 1998 Audi A4

1 Answer

Clutch not primming in r32 skyline


You either have air in the system or a faulty master cylinder.

Check fluid is being delivered from the master cyl. by slackening off the hydraulic line connection at the master cylinder while depressing pedal.
Until fluid is able to be delivered from the master cyl. itself you have no hope of bleeding the rest of the system.

As with all hydraulic bleeding processes, only release the fluid line when the pedal is being pushed slowly down or held down against the return spring pressure of the clutch pressure plate - re-tighten it on the upward stroke of the pedal to stop it drawing air back into the system.

If you are confident that there is fluid delivery from the master cyl. move to the clutch slave cylinder.

Again only open the bleeder valve when the pedal is being pushed slowly down (i.e. the hydraulic system is pressurised).

(If you keep the master cylinder full of hydraulic fluid, sometimes gravity will cause the line to 'self bleed' if the bleed nipple is left slightly open for several minutes at the start of the bleed process).
When fluid appears, finish the slave cylinder air bleed in the normal way.

If you have the time to spare, I have often found that provided the master cylinder is kept full, leaving the system overnight will allow a lot of the air to leave the system (gravity helps).

May 31, 2009 | 2002 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...