Question about 2007 BMW X3 3.0si SAV

Open Question

BMW 2008 X3 - Left turn signal came on and the high beam light is on - no way to cancel

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: DRL and High Beam do not work right on Honda Accord EX 1998

Some time back I found some data on a similar website suggesting that the Day Light Running circuit board, just under the steering column, developed cracks in some of the soldered joints. Your high beams should also be affected with loss of day light running lights.
Resoldering repaired the continuity of the circuits. Ours is now working quite reliably. Some of the defective areas developed slight brownish discoloration, that's how I was told to recognise the areas to be resoldered. Hope this will help you solve your problem.

Posted on Jun 10, 2008

Ad
bunnydawg
  • 5158 Answers

SOURCE: 2004 BMW X3, 3.0, 64K; Electrical problems

locate the relays that control those things on the engine compartment fuse box located near the battery... replace them

Robert

Posted on Jan 21, 2009

  • 3600 Answers

SOURCE: all lights lit up on dashboard while driving

It's Under warrenty take it in you have had a massive failure most likely the battery went dead or out of oil or fluids.

Posted on Oct 20, 2009

roniecon
  • 6826 Answers

SOURCE: Low beams shut off and won't come on other lights

Either the low beam head light bulbs have went out,or the dimmer switch has gone out.

Posted on Oct 22, 2009

  • 1 Answer

SOURCE: 2008 BMW X3, removing the left rear outer door

2004 x3 Rear passenger door handle came off/apart. What are the steps to remove the inner door panel to access the door handle and repair it?

Posted on Oct 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 chev sub head lights wont turn on


Do you know anything about automotive electronics ? Electronic control modules .
Headlamp ON/OFF control is determined by the body control module (BCM) by a signal on the headlamp switch on input circuit when the headlamp switch is in the HEAD position. When the headlamp switch is in the AUTO position, the BCM determines headlamps ON/OFF by the voltage from the ambient light sensor.
If the headlight switch is left in the ON position, the inadvertent power control feature will turn OFF the headlights approximately 10 minutes after the ignition switch is turned to the OFF position. If the driver places the headlight switch in the ON position after the ignition switch has been turned OFF, or if the ignition switch is in the ACCY position, the headlights will remain ON until turned OFF or the battery runs dead.
The high beam indicator is illuminated when the instrument cluster receives a GMLAN serial data message from the BCM that the high beams are illuminated.
High Beams
The high beam headlamps receive voltage from the headlamp high relay located in the underhood fuse block. The BCM controls the relay on the headlamp high beam relay control circuit. High beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is grounded, the BCM grounds the headlamp high beam relay control circuit, illuminating the high beam headlamps. The right and left high beam circuits are independent and are fused independently in the underhood fuse block.
Low Beams - Standard
The low beam headlamps receive voltage from the headlamp low beam relay located in the underhood fuse block. The BCM controls the relay on the headlamp low beam relay control circuit. Low beam control is determined by a signal on the headlamp dimmer switch signal circuit from the multifunction switch. When the headlamp dimmer switch signal circuit is open, the BCM grounds the headlamp low beam relay control circuit, illuminating the low beam headlamps. The right and left low beam circuits are independent are fused independently in the underhood fuse block.

Hooking up a factory scan tool an checking DTC'S - diagnostic trouble codes would be the very first step in trouble shooting this problem .
DTC B257A 00: Headlamp Switch Input Signal Mismatch
DTC 2575 00: Headlamp Control Circuit

Jun 30, 2017 | Cars & Trucks

1 Answer

Turn signals and high beams


First check around all the lights (front, rear, headlight, turn signal, parking, fog, etc..) for loose, broken, or bare wires, and/or loose , broken, or bad connectors. Any of these could cause the lighting to short. If everything is in good working order, then the problem will most likely lie with switch inside the column (the lever).

Jul 15, 2008 | 2001 Volvo S80

1 Answer

My left turn signal come on and the high beam light...bm3 x3


Check your grounding at the light unit (most probable) - with no defined return path for the electric, it'll go where it can and light-up any number of things though none, efficiently - we also call it the 'earth' which may simply be loose or corroded.

Mar 24, 2013 | 2007 BMW X3 3.0si SAV

1 Answer

My light problem is i have low beam on right side no low on left side i turn highs on and right side goes out and high on left turns on then when back to lows beams and i pull turn signal to flash high...


If you have separate bulbs for the low and high beams(4 light system), if you pull the turn signal and hold it, all 4 lights will stay on until you release the turn signal. You need to replace the bright bulb on the right side and the low bulb on the left side. If your headlights only have one bulb on each side, then you will have to replace both of them to get everything to work.

Jan 04, 2011 | 2000 Ford Mustang

1 Answer

2008 BMW X3, removing the left rear outer door handle.


2004 x3 Rear passenger door handle came off/apart. What are the steps to remove the inner door panel to access the door handle and repair it?

Apr 06, 2010 | 2007 BMW X3 3.0si SAV

1 Answer

2004 BMW X3 driver side low beam headlight


remove the air filter housing ,simple .this programme has a spell check thingy working and its driving me nuts ,it cant identify plain english ,write colour and it squiggles it out but color is ok .

Oct 30, 2009 | 2004 BMW 3 Series

1 Answer

2004 BMW X3, 3.0, 64K; Electrical problems


locate the relays that control those things on the engine compartment fuse box located near the battery... replace them

Robert

Jan 21, 2009 | 2004 Kia Sorento

Not finding what you are looking for?
2007 BMW X3 3.0si SAV Logo

Related Topics:

428 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...