Question about 2004 Mitsubishi Outlander

Open Question

Cam belt change on mitsubishi challenger 2004 v6 3l

I am looking for information on how the change the cam belt on a mitsubishi challenger V6, 3.0.

I need the timing marks information as well.

Please guide me to a website or provide manual to assist.

Posted by on

5 Suggested Answers

mjvgamer
  • 7 Answers

SOURCE: how to change the fuel pump on a 1994 Mitsubishi Montero LS 3L V6

just for you REMOVAL & INSTALLATION
See Figures 1 and 2
WARNING In almost every case, replacing the Mitsubishi electric fuel pump requires removal of the fuel tank. Please refer to the fuel tank removal and installation procedure at the end of this section.

  1. Lift or move aside the carpet in the rear cargo area.
  2. Remove the oval cover plate from the access hole.
  3. Disconnect the fuel pump harness connector at the rear of the fuel tank.
  4. Start the engine, allowing it to run until it runs out of fuel. This relieves pressure within the fuel system.
  5. Turn the ignition switch OFF and disconnect the negative battery cable.
  6. Remove the fuel filler cap.
  7. Drain the fuel from the fuel tank into suitable container(s), each with an airtight lid.
  8. Carefully, and using two wrenches on the fittings, disconnect the high pressure fuel line and the main fuel line from the pump. Remove the high pressure fuel hose at the body-side main pipe connection, unfasten the pump-side connection. Wrap each joint in a rag before loosening; some pressure may remain within the system.
  9. Remove the fuel pump retaining nuts and carefully remove the pump from the tank.
The fuel pump may still contain liquid fuel. Drain it into a suitable container with an airtight lid before performing any tests or inspections.
To install:
  1. Carefully install the pump into the tank and install the 6 retaining nuts onto the studs. Tighten the nuts evenly and in a crisscross pattern to 12 ft. lbs. (16 Nm).
  2. Reinstall the high pressure and supply line to the pump.
WARNING Take great care when connecting the threaded high pressure lines. Start the threads by hand, then, while holding the hose side to keep it from turning, tighten the flare nut to 27 ft. lbs. (37 Nm).
  1. Connect the pump wiring harness.
  2. Connect the negative battery cable. Turn the ignition key to ON but do not start the engine. You should hear the pump running. Allow it to run for about 10 seconds to build line pressure, then start the engine.
  3. After the engine has run smoothly for a minute or two, shut the ignition off and check the work area for any trace of leakage. Attend to any fuel leaks immediately, remembering that the system has repressurized and must be handled safely.
  4. Reinstall the cover on the access hole and replace the carpet in the cargo area.
0900c152800547c3.jpgFig. 1: Components of the fuel pump and fuel tank 0900c152800547c4.jpgFig. 2: Components of the fuel pump-all models similarTESTING
When diagnosing engine problems, particularly a "no start" condition, the fuel pump function should be checked. Because of the difficulty in reaching the fuel pump connections, Mitsubishi automobiles have a conveniently located test connector under the hood. V6 Monteros have the connector taped to a wiring harness inside the right front kick panel, near the ECM and relays.
This connector bypasses all of the controls in the system (ignition switch, pump relay, etc.) and sends voltage directly to the pump. When power is applied to the pump you should be able to hear it running, although the in-tank pumps require you remove the fuel filler cap and listen at the filler.
To use the test connector, make certain the ignition is OFF. Great damage may be caused if the system is tested with the key on. Locate the test connector in the engine compartment (on later Monteros it is located under the right-hand side of the dashboard)-it is generally on a short lead out of a wiring harness and looks like a plug that isn't connected to anything. Once found, use a jumper wire to connect the test terminal to the positive battery terminal. Listen for the fuel pump; if it runs, you know the pump motor is good. While the pump is running, gently squeeze one of the fuel lines and confirm that the pump is delivering fuel pressure. If it does not run, the pump itself is most likely defective OR the connector to the pump is faulty.
When the pump is removed from the tank, it may be checked by applying battery voltage (+) to the connector and grounding the housing. Only run the pump for one or two seconds during this test; the pump can be damaged by running without liquid.
CAUTION Make certain the pump has been drained of residual fuel and is free of fuel vapors. Connecting and removing the test leads will cause sparks which can ignite any vapor in the area.

Posted on Jan 18, 2009

ewashmidas
  • 362 Answers

SOURCE: Cam Belt on Outlander 2.4 litre Petrol - 2004

The vehicle has a belt and should be changed every 60,000 miles.

Posted on Jan 31, 2009

  • 718 Answers

SOURCE: need to know about changing the timing belt on my 2001 mitsubishi

This will take about 3-4 hours. If you look at the drive belts, they will all have to be taken off to get to the timing belt. The engine crankshaft has to be positioned for marks to line-up. The crankshaft will have to be prevented from turning so you can take off its drive pulley. Rotate until the alignment cylinder is near TDC, remove sparkplug, then packing a small rope on top of the piston prevents the engine from turning.. Once you change one timing belt, you will never buy another car with a timing belt again. You can get a manual on eBay.

Posted on Mar 27, 2009

  • 24 Answers

SOURCE: i need to find a timing belt diagram for a 1994 mitsubishi galant

Your car will have the 2.4L SOHC engine in it (AKA 4G64). This manual will show you how to replace the timing belt (and more). Timing belt procedures start on page 33.

http://www.scribd.com/doc/4570538/Mitsubishi-4G63-4G64-Engine

(P.S. this manual also includes the 4G63 engine, you can identify your engine by looking at the procedures for the Single OverHead Cam[or SOHC])

Posted on Apr 07, 2009

  • 5 Answers

SOURCE: routing guide for serpentine belt

f35bdee.gifhope

Posted on Apr 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vibration in my Mitsubishi challenger over 60, new tail shaft new bearing in gearbox, still has not fixed. What else could it be?


maybe something loose under the body , stone skirts or worn ball joints , steering or suspension bushes. if its not the engine , or the engine could be out of balance many overhead cam motors have a second counter weight that runs from timeing belt, belt can break but engine shakes at high revs.

Jun 02, 2015 | Cars & Trucks

2 Answers

Replace transmission control switch on mitsubishi challenger


Montero or Challenger? Both on the drivers side of the transmission. Big black switch under where the shifter cable goes to the transmission. Under the vehicle.

Feb 11, 2015 | 2004 Mitsubishi Montero Sport

1 Answer

Mitsubishi GDI 3500 engine 6G74 it cranks but no spark any solutions


Got Mitsubishi challenger 6g74 there is no spark, changed the crank and cam sensor, fuel is coming but still no spark. please help

Apr 24, 2013 | Mitsubishi Montero Cars & Trucks

1 Answer

Timing belt


If this has more than 60,000 miles on the belt you are looking for trouble. I haven't found the repair procedure for free on any search I've tried of the many sites that post the info so I'd suggest you pay for the information from this site, also do the water pump and idler pulley, there is a timing belt kit and I'd highly recommend it be used, you can find them here

Sep 06, 2012 | 2004 Mitsubishi Outlander

1 Answer

How to check if cam belt worn or still good.


You will get no warning and physically checking it will tell you nothing unless there is obvious damage. Don't risk it, change when the manufacturers says normally around 80 000km intervals and even less if the cambelt has been changed before

Jun 29, 2009 | 2004 Mitsubishi Outlander

1 Answer

Cam Belt on Outlander 2.4 litre Petrol - 2004


The vehicle has a belt and should be changed every 60,000 miles.

Dec 08, 2008 | 2004 Mitsubishi Outlander

1 Answer

Cam belt?


its a timing belt attacked to the side of engine then you have 3 open belts. The timing belt is connected to crank at engine to camshaft for cylinders. if incased it is a timing belt. it will be a challenge to put on.

Oct 16, 2008 | 1989 Mitsubishi Galant

Not finding what you are looking for?
2004 Mitsubishi Outlander Logo

Related Topics:

606 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6879 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...