Question about 1999 Chevrolet Malibu

1 Answer

If i just rebulit my motor put in new cooling system sencers and car is still over heating what did i miss

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

Raidiator,cap,water pump.Try the cap first cause if there is just the smallest crack in the rubber seal it will not hold pressure and cause it to overheat.

Posted on Dec 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I got a 95 tahoe the trans has been rebulit and the rear end has been replace but i feel a vibartion when i mash own the gas


CHECK FOR LOOSE OR MISSING FASTENERS, BRACES ETC.
SOMETHING GROUNDING OUT (HITTING) WHEN MOTOR IS TORQUED.

Dec 27, 2013 | Cars & Trucks

1 Answer

700r4 trans. rebulit download


Welcome to http://www.stylemalls.com//

where is the most popular Panthers online shop.


((( http://www.stylemalls.com/ )))

lower price fast shippment with higher quality!!

WE ACCEPT CREDIT CARD /WESTERN UNION PAYMENT
YOU MUST NOT MISS IT!!!

Jul 04, 2013 | Cars & Trucks

1 Answer

Cam shaft position sensor 350z


The Cam Shaft Position is behind the motor on passenger side and has a green cap with 2 little wires going to it .with a 10 mm bolt to take out now what most people on here did not tell is that it was hard to take the green cap off the sencer first because the clip is on the bottom so you cant see it to take it off and if you just try to take a flat head screw driver to it you will bust your green clip.so take the sencer and cap off together and then take the green cap off after you get the sencer out .ok when you take the 10mm bolt out then you can reach down and pull the sencer out but its pretty hard just to pull out your going to want to twist it but you dont have to you are just pulling against the rubber O ring thats on the sencer just pull hard and it will come out.then pull the cap off .you acually push in on the clip towards the sencer to get it off ,not down ,but towards the bolt hole ,to take off,repalce clip put new sencer on and put sensor in motor,dont wiggle around on the wires to much because they are little and I could see braking one if not both

Mar 23, 2012 | 2004 Nissan 350Z

1 Answer

I have a 1998 chevy suburban that I bought. The motor was bad (through the number 5 piston) I put a nother motor in it but the block that I put in was a older block four bolt I put a steel crank in it and...


you cant use the cam gears on your "new motor' the cam gear from the old one must be used if it will fit.the starter problem could be a bad solonoid or a wireing problem cant tell by your desciption.

Jul 17, 2010 | 1998 Chevrolet Suburban

2 Answers

Oveheating


did you flush the radiator and change the uper hose? If you have changed the water pump and sencers have them checked they may be factory defected.

Jul 14, 2009 | 2002 Chrysler PT Cruiser

2 Answers

Why is it overheating?


Sorry but its common for this year to have a hyd cooling fan motor to go bad along with the coolant degas tank breaking...you'll need ford pn# XW4Z-8K621-AA motor and a # 388898S washer to replace, along with the degas tank..don't forget p/s fluid to refill the system...BESURE you totally PURGE the cooling or it will O/Heat in 2 blocks ....hope this helps you...GL

Jul 08, 2009 | 2003 Lincoln LS

2 Answers

I have a 1993 cutlass ciera s and it dies


my 93 olds stalls then dosent turn over but i take ecu fuse out and wait a few minutes it will start and run till next time it decides to stall

May 14, 2009 | 1993 Oldsmobile Cutlass Ciera

1 Answer

1998 cavalier heats up when idleing. Fan comes on but still heats


Hello senior, whenever the coolant system is opened up there's a possibility you could get air in your system, only way to get it out is by using the bleeder valve, check the coolant temperature sensor it may not be working properly, it tell's the cooling fan when to kick on and off, the condition of the drive belt is also another factor, along with the tensioner and tensioner pulley. it sounds like a problem with the water pump, the cooling fan, or air in your cooling system, to get a good inspection of the water pump fin's you have to remove it.

Apr 03, 2009 | 1998 Chevrolet Cavalier

2 Answers

Kia sportage 2.0l sohc timing


so far i beleve there is no way to change the timing on this car try relpacing the cam sencer with a new one and or the computer for the car i had the same problem i got a new wireing harnes computer and all new sencers and electronic valves to fix my car it is like putting anew motor in the car lots of work but was worth it in the end

Jun 06, 2008 | 1995 Kia Sportage

Not finding what you are looking for?
1999 Chevrolet Malibu Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...