Question about 1993 Ford Ranger SuperCab

1 Answer

I went to work today and the brakes were fine. then when i went to leave work the brake pedal went to the floor and i couldnt stop. so i bled the brakes from the right rear all the way around and still nothin. what else is there to do? i have checked the fluid too.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 47 Answers

First determine if either of the wheel cylinders or calipers are leaking. Be sire to check the brake flex lines as well. If all the hydraulics are dry, look at the master cylinder where it attaches to the Brake Booster. On the bottom, below the Master Cyl, is it dry or does it look like there is some leakage? If it is wet, and all the above check out OK, then I would replace the Master Cylinder.
Be sure to bench bleed the master cylinder first, before installing on Vehicle.

Posted on Dec 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2000 Grand Prix the brake pedal just went to the floor. What is wrong :(


It could be that your brake fluid reservoir is empty. You might also have a crack in the line.

Mar 08, 2015 | 2000 Pontiac Grand Prix GTP

1 Answer

Brake pedal goes to the floor when I push the pedal, push the pedal again and it works fine.


You have air in the braking system, the first press compresses the air and forces it into suspension in the brake fluid, allowing the second press to operate the brakes, then, when you leave it alone, the iar seeps out of suspension, back into being air in the pipe and it all happens again.

You need to get your brakes bled. More to the point, you need to figure out how the air got IN there! Has someone taken the brakes apart or removed and replaced a brake caliper, piston or pipe?

Jul 07, 2011 | 1996 Mercury Villager

1 Answer

After having changed the rear brake shoes and wheel cylinders, and bled them the pedal was good. Then the pedal was going to the floor slowly so I had to pump the brakes to get enough stopping power....


It sounds that you have done a pretty good job at this point. Remember that the brake adjustment will dictate the amount of brake pedal. Recheck to make sure the right brake linings were used. Recheck to make sure the brakes on the rear are adjusted up as far as possible. As far as the bleeding, I have had many cars that will not bleed the sytem without the engine running to give it the pressure needed to pass through the master cylinder and lines. Have a WELL ventilated area, car in neutral, wheels chocked, and bleed the brakes with the engine running. Remember to take all safety precautions to avoid injury before attempting this.

Dec 29, 2010 | Honda Civic Cars & Trucks

1 Answer

Brake pedal falls after stopping on 1995 suzuki sidekcik. replaced master cylinder and two rear wheel cylinders and bled system but issue still there. Brakes work fine but after you come to a complete...


I think u got problem on ur rear brake regulator, check that regulator that is located between the two rear brake lines.

The purpose of that barke pressure/limiter regulator is to control the hydraulic pressure on both rear brakes, bleed that and check if the and clean it.....

Dec 02, 2010 | 1995 Suzuki Sidekick

3 Answers

While driving my 1994 Honda Accord the brakes went out. I can only get the car to stop if I press the brake pedal all the way down to the floor. When the car is shut off and I pump the brake pedal, I can...


There may be air in the lines. Bleed all your brakes starting at the farthest wheel from the resevoir, and finishing at the closest one. Try the pedal after its bled. If the pedal still feels soft or travels to the floor there may be a pinhole leak that may be spraying on the underbody of the car, or the seals in the master cylinder are gone filling the vacuum booster(if equipped). Air compresses more than oil so if bleeding works that may be the problem.

Feb 21, 2010 | 1994 Honda Accord

1 Answer

I have a 94 cavalier rs and i put a rear wheel cylinder in it and i started to bleed the brakes and i bled the right rear and it bled fine then i went to the side where i put the wheel cylinder in and it...


well sounds like its still full of air youll have to gravity bleed it. if you can leave your car on a steep hill overnight with the rear end up then bleed it the do the same make your front end sit high up overnight then bleed it. air bubbles always try to make their way to the highest point

Oct 19, 2009 | 1994 Chevrolet Cavalier

1 Answer

Brake pedal to floor


Change the brake caliper. This should do it.

Rate this

Apr 05, 2009 | 1995 Toyota Camry

1 Answer

Car would not stop


You need to have your brakes checked TODAY. They at least need the air bled out of them and adjusted but possibly you need a wheel cylinder ir caliper rebuilt or replaced. You have a leak somewhere.

Feb 04, 2009 | 1996 Lincoln Town Car

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5530 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...