Question about 2005 Chrysler Sebring Conv

1 Answer

The windshield washer just quit working fuses are good reservoir is full. i cannot tell if the pump is working or not. i cannot get to intake hose the reservoir is impossible to acess

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Check the supply lines from the reservoir to the outlets. the line runs under the heat blanket attached to the bottom side of the hood. These lines get brittle with cold and age. Mine broke last winter. Less than $2 for splices at auto parts store and I was back in business. Have someone turn on the sprayer while you look under the hood. if spray is not working, fuses are good, it is probable the sprayer motor. Check the supply lines first.

Posted on Jan 08, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is fuse for 1997 mercury wagon for windshield wipers


1997 mercury wagon ? Sable ? VISUAL INSPECTION CHART-WINDSHIELD WIPER AND WASHER SYSTEMS Mechanical Electrical
  • Windshield wiper blade missing or damaged.
  • Binding windshield wiper pivot arm.
  • Binding windshield wiper mounting arm and pivot shaft.
  • Empty windshield washer reservoir.
  • Kinked or broken windshield washer hoses.
  • Open fuse junction panel Fuses:
    • 8 (5A)
    • 12 (5A)
    • 20 (5A)
    • 23 (5A)
  • Damaged windshield wiper motor.
  • Damaged windshield washer pump.
  • Open connectors.
  • Corroded connectors.
  • Inoperative multi-function switch.
  • Open thermal breaker internal to the wiper motor

Which are not working , front , back or all ?

I/P Fuse Panel C225
Under left corner of instrument cluster

Feb 05, 2017 | Mercury Cars & Trucks

1 Answer

Where is the fuse for the water pump for the window washer


A washer pump in a car's windshield wiping system moves washer fluid from a reservoir through hoses. The motorized pump pressurizes the fluid to allow it to be squirted from the hoses through nozzles onto the front and/or rear windshield of a car. The washer fluid helps windshield wipers get rid of rain, dirt, or other objects that can interfere with a driver's visibility. If your washer fluid is not being sent out when activated, the solution could simply be filling the washer system's reservoir with more fluid or cleaning the nozzles and hoses. In more severe cases, the washer pump may need to be replaced. Here are steps to troubleshoot a windshield-washer pump.

Try this link in case you are stuck:

How to Troubleshoot Windshield Washer Pump

Here is another YT video for a similar purpose:

Windshield Washer Pump and System Diagnosis

Apr 13, 2015 | 2001 Ford Explorer Sport Trac

2 Answers

Windshield washer fluid quit working on my 2011 Freightliner Cascadia


There's a few things you might want to check. First, check to make sure the washer fluid reservoir is completely (assuming you hadn't already done that). After you are certain the reservoir is full, look for any possible leaks...either the reservoir or the hoses going from the tank to the windshield. If the tank and hoses are intact, turn on your windshield wipers...then try running the pump. If no washer fluid comes out, and for this you might need another person to assist you, try running the pump again...listening to make sure the pump is in fact running. If the pump does run but still no fluid comes out, inspect all of the hoses as well as all of the outlets where the fluid sprays the windshield...it is possible that the outlets may be plugged. Some common reasons for the outlets to be plugged...debris, dirt/mud, and/or wax (has anyone recently waxed your Freightliner?). Just to be sure, using a small needle or even a wire, ensure each outlet is cleared and not obstructed with anything. After that, try running the pump again. If no luck, try removing the hoses going from the tank to the windshield. Once removed, using something like a wire coat hanger, clear each hose for any possible obstruction. Reattach hoses and try running pump again. If still no luck, I would guess the problem might be located with the washer pump itself. Before opting to replace the pump, if you believe that is the problem and the pump just doesn't operate, check all fuses and inspect any/all wiring connections.

Good luck
Jason

Jun 24, 2014 | Cars & Trucks

1 Answer

Windshield washer stopped working


Can you hear the pump when you try the windshield washer? If not you may need a new pump. Before doing that I would trace the washer hose from the reservoir to the wiper blades or the little jets. These may be you problem but you should be able to tell if the pump is running first. I wold also check the fuse box and make sure it is not simply a blown fuse.

Jul 10, 2012 | Cars & Trucks

2 Answers

Water is not comming out of my windshield washer. What will I do?


Check you pump fluid maybe is not work (listen when turn on)

With a clip, clean the hoses in the windshield ejectors-water.

Good luck.

Sep 25, 2009 | 1995 Chrysler Concorde

1 Answer

Mercury villager 1994 washer pump not working


the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal
  1. Disconnect the battery ground cable (14301).
  2. Raise and support the vehicle.
  3. Remove the RH wheel (1007).
  4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
  5. Remove the windshield washer reservoir top bolt.

  6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
  7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
  8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
  9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
  10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.

    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.

  11. Loosen the two windshield washer reservoir side bolts.
  12. Remove the windshield washer reservoir by sliding it out of the side slots.
  13. Remove the windshield washer pump.

    Installation
To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

Sep 09, 2009 | 1994 Mercury Villager

2 Answers

Windshield washer not working properly


If you have used ANYTHING beside windshield solvent in you reservor, you may have created WAXING from soap in the bottom of washer tank, which clogs pump,lines, and nozzel....take the tank out and wash it..disconnect washer hoses at nozzel and clear with compressed air along with the nozzel...if you use solvent only you may have a worn washer pump or restriction...check those and good luck.....

Jul 04, 2009 | Ford Five Hundred Cars & Trucks

1 Answer

Wash wipe on a Focus 2000 model


I blieve it's the same pump taht runs the rear and front washers.

The windshield washer comprises the following parts:
  • Windshield washer reservoir, below the front left-hand fender
  • Washer pump, on the outside of the washer reservoir
  • Two washer nozzles on the hood/bonnet, adjustable.
---------------------------------------------------------
Windshield Washer Pump and Reservoir Removal
All vehicles
  1. Remove the windshield washer reservoir filler neck.
  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the right-hand fender splash shield (wheel shown removed for clarity).
  1. Remove the washer reservoir.
    • Disconnect the electrical connectors.
    • Pull off the hoses.
  1. Remove the windshield washer pump with rubber gasket (shown with reservoir installed).
    1. Disconnect the electrical connector.
    1. Disconnect the hoses.
    1. Lift out the pump.

Feb 27, 2009 | 2000 Ford Focus

1 Answer

Windshield washers not working


I wouldn't worry about tracing the hose just yet, most likely it's a bad pump. Find the wire(s) going to the pump, usually on the bottom of the reservoir and connect a test light to a good ground. Then have someone try to 'squirt' the washer fluid while you touch the test light 'probe' to the pump's wire connector. If it lights but no fluid squirts, it's bad. They are cheap and usually very easy to replace. If it doesn't light there's a brake in the circuit somewhere. (bad fuse, bad connector, etc.) Good luck.

Jan 18, 2009 | 2005 Pontiac Vibe

2 Answers

Wiper fluid level sensor replacement


Reservoir —Windshield Wiper

Removal
  1. Remove the RH wheel; refer to Section 204-04 .
  1. Position RH splash shield aside.
    1. Remove six screws.
    1. Remove three pin-type retainers.
    1. Position RH splash shield aside.
  1. NOTE: Windshield washer fluid should be collected in a container after the windshield washer hoses are disconnected.
    Disconnect the electrical connector and washer hoses.
  1. Remove the upper reservoir bolt.
  1. Remove the windshield washer reservoir.
    • Loosen the two lower reservoir bolts.
------------------------------------------------------------------------------------

Jan 15, 2009 | 2000 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...