Question about Nissan Sentra

Open Question

My 2007 Nissan sentra keyless entry does not work, the car does not detect the key with either remote.

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: nissan murano 2005 sl keyless entry remote programing

Close all vehicle doors, LOCK doors using drivers side switch.

Insert key all the way into the ignition, (do not turn) remove key.

Repeat this step 5 times. (6 total)

Hazards should flash to indicate program mode.

Press any button on transmitter to be programmed, hazards should flash to indicate successfull program.

*For additional remotes, cycle drivers door lock UNLOCK, LOCK, press any button on remote, hazards should flash. Repeat step as necessary.

Ignition ON, (engine off) ignition OFF, UNLOCK using drivers side switch, test remotes.

Source

Posted on Aug 06, 2008

Ad
  • 85 Answers

SOURCE: remote keyless entry

“CUSTOMER LEARN” MODE This feature is only available on domestic vehicles or those which have a U.S. country code designator. This procedure requires access to at least two valid Sentry Keys. If two valid Sentry Keys are not available, Sentry Key programming will require the use of a scan tool.
The steps required to program Sentry Keys with two valid Sentry Keys follows:
1. Obtain the blank Sentry Key(s) that need to be programmed. Cut the keys to match the ignition lock cylinder mechanical key codes. 2. Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the ON position. 3. After the ignition switch has been in the ON position for longer than three seconds, but no more than fifteen seconds, cycle the ignition switch back to the OFF position. Replace the first valid Sentry Key in the ignition lock cylinder with the second valid Sentry Key and turn the ignition switch back to the ON position. The second valid Sentry Key must be inserted within 15 seconds of removing the first valid Sentry key. 4. About ten seconds after the completion of Step #3 , the indicator light will start to flash and a single audible chime tone will sound to indicate that the system has entered the "Customer Learn" programming mode. 5. Within sixty seconds of entering the "Customer Learn" programming mode, turn the ignition switch to the OFF position, replace the valid Sentry Key with a blank Sentry Key transponder, and turn the ignition switch back to the ON position. 6. About ten seconds after the completion of Step #5 , a single audible chime tone will sound and the indicator light will stop flashing and stay on solid for three seconds and then turn off to indicate that the blank Sentry Key has been successfully programmed. The SKREES will immediately exit the "Customer Learn" programming mode and the vehicle may be started using the newly programmed Sentry Key.

NOTE: The Remote Keyless Entry (RKE) Transmitter will also be programmed during this procedure. These steps must be completed in their entirety for each additional Sentry Key to be programmed. If any of the above steps are not completed in the given sequence, or within the allotted time, the SKREES will exit the "Customer Learn" programming mode and the programming will be unsuccessful. The SKREES will also automatically exit the "Customer Learn" programming mode if:

  1. It sees a non-blank Sentry Key when it should see a blank.
  2. If it has already programmed four (4) valid Sentry Keys.
  3. If the ignition switch is turned to the OFF position for more than about fifty (50) seconds.

NOTE: If you attempt to start the vehicle while in “Customer Learn” mode (LED flashing), the vehicle will behave as though an invalid key is being used (i.e. the engine will stall after two (2) seconds of running). No faults will be logged.
NOTE: Once a Sentry Key has been programmed to a particular vehicle, it cannot be used on any other vehicle.

Posted on Aug 05, 2008

limotec
  • 33 Answers

SOURCE: Reprogram a keyless entry remote

Hello
this is how to program the remotes/keyless entry

How

  • Obtain all remote transmitters
  • enter the 5 digit permanent code into the keyless entry pad on the drivers door
  • Press the 1-2 switch on the keyless entry pad
  • Within 5 seconds
  • Press any button on the first remote transmitter
  • The doors should open then lock
  • Within 5 seconds
  • press any button on the second & third remote
  • within 5 seconds for each remote
  • to exit programming
  • simultanionusly press 7-8 & 9-0 switchs on the key pad or wait more then 7.5 seconds
NOTE
The 5 digit permanent code is located in one of the following places
  1. On the owners warranty card
  2. On the label on the inside the trunk/ boot
  3. On the owners code card
  4. On the centrel locking control module located in the drivers door
  5. In the PCM ford can get this for about $25.00
I hope this help
Regards Paul
www.limotec.co.uk

Posted on Jan 13, 2009

  • 1 Answer

SOURCE: Where can you purchase battery for keyless entry for 2007 Nissan

I got mine at walgreen's!!!

Posted on Jun 18, 2010

  • 2 Answers

SOURCE: Lexus 1994 LS400 remote key won't work

also check the 30 amp fuse which says door beneath the left drivers's side near the foot rest.

Posted on Apr 06, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many wire harness clips connect to rcdlr module on 2007 impala besides the antenna


2007 Chevy Impala Keyless Entry: Keyless Entry Only ...

www.2carpros.com/questions/2007-chevrolet-impala-chevy-keyless-entry
Dec 30, 2010 - CHEVY KEYLESS ENTRY ... 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar. 5. ... Connect the new antenna to the RCDLR antenna module. 11.... The existing antenna is grounded into another wiring harness.

TPMS and key FOB range problems - LS1TECH

ls1tech.com/forums/ls4.../719926-tpms-key-fob-range-problems.html
May 24, 2007 - 2006-2007 Chevrolet Impala, Monte Carlo ... Remove the clips holding the RCDLR antenna wire at the RCDLR module and along the "A" pillar.

Buick Workshop Manuals > Lucerne V6-3.8L (2007 ...


Dec 01, 2015 | 2007 Chevrolet Impala

1 Answer

Where can i find the relay or fuse of the remote keyless entry in my 2006 nissan sentra?


http://www.b15u.com/threads/36-Relay-amp-Fuse-Diagrams

The room lamp check fuse then the relay for keyless in passenger fuse panel

May 16, 2015 | 2006 Nissan Sentra

1 Answer

My 2009 keyless entry will not start?



Nissan cars with keyless entry will display key on dashboard display if battery of key runs out. Normally it can be resolved by replacing the battery. See video above.

Emergency Start: There is a way to start the car in case of emergency. If you don't have access to new battery then you can start the car by pressing the button with your key FOB. There is a sensor in your key below Nissan logo which should be kept near the Start-Stop button when pressing it. This should work even if there is no battery in the key. You can give it a try.

Feb 05, 2013 | 2009 Nissan Sentra

1 Answer

2005 Nissan Sentra, the keyless entry locks the doors but does not unlock them.


does your unlock button work in car? If it does, do you have another keyless entry key fob? If so does it work? If you just replaced the battery you can try removing battery and cleaning contacts within remote. I know some of the nissan altimas had the same issue and the only solution was a new key fob. Good Luck

Jan 04, 2013 | 2005 Nissan Sentra 1.8

2 Answers

Keyless remote is not working & alarm goes off & won's turn off


before doing anything... use the key to unlock the door...then the alarm will not go off

Jul 20, 2010 | 2008 Nissan Sentra

2 Answers

Where can you purchase battery for keyless entry for 2007 Nissan


The best place to purchase a replacement battery is AutoZone. They have a tester there to make sure everything is working. It should be on the help counter.

Jul 15, 2009 | 2007 Nissan Maxima 3.5 Sl Sedan

2 Answers

Door lock


Make sure the battery on your Keyless Entry remote is a working battery.

If thats not it, it could very well be the actual button on your Keyless Entry remote being faulty. But it could also be a relay in the car aswell. Depending on the cost of a Relay versus the cost of a Keyless Entry remote, I would try to replace either/or and try again, whichever is cheaper. The Relay may be cheaper, but your Key-FOB sounds like it could be the cause.

May 16, 2008 | 1994 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...