Question about 1996 Ford Taurus

1 Answer

Vaccum lines need diagram of vaccum lines that lead to and from the egr box ASAP! I really have a problem any help is better than no help...thanks

Posted by on

  • Anonymous Mar 13, 2014

    need vaccume line diagram

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 61,252 Answers

There is a diagram for that system under the hood above the radiator, the 2 lines go to 2 exhaust tubes, one is pressure and one is reference, the hose size is different so you can't get them mixed up, the EGR "box" is the EGR pressure transducer and the signal from that controls the EGR through the Power Train Control Module AKA the PCM. You have to use special
Hi-temperature silicone rubber hoses from the Ford dealer, ordinary rubber hose will just burn up in short order, they are around $15-20

Posted on Aug 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Vacuum diagram nissan


It should go to a control solenoid that controls vac to the valve. You may need to hunt up a shop manual to get the hose diagram or look at a junk engine.

Jul 13, 2013 | Cars & Trucks

1 Answer

I have a 1999 mazda b2600 it keeps coughing and splattering . I have changed the leads plugs dizzy cap o2 sensor and i bought a second hand air flow meter can anybody please help me out ? Thanks and its a...


egr position sensor aka the dpfe is often the culprit, its mounted on the firewall and has an electric connector and vaccum lines going to it.

Dec 05, 2012 | Cars & Trucks

1 Answer

Chevy Engine Swap, Blazer 350 into my El Camino


Yes, the engine will swap fine, for the vacuum lines Go to Autozone.com, become member, will give you repair manual,location of parts,diagrams.

Jul 12, 2012 | Cars & Trucks

1 Answer

I need to know where my egr valve is and upper penium so that I can remove the egr valve the easiest way. I am a woman but I have to do it myself and I could use a diagram or good instructions and the...


Nikki, sorry I don't have any pictures of your EGR valve but a lot of parts stores have on line catalog so you can see what it looks like. The EGR valve is there a two bolts that hold it to the intake manifold should be a 10 mm head and they are going to be tight so make sure you use a good quality 6 point socket. On your engine the EGR vavle bolted to the intake manifold between the throttle body and the distributor. It is kind of a mushroom shaped thing with a rectangular base made of cast iron. The round mushroom looking part has a small vacuum hose going to it. Also, if you going to be doing you own repairs you really need a manual. A Chilton's book for that rig should only be about fifteen bucks, if you really can't buy one check out the library. Also, there is not a lot you can do to make a dead EGR valve work again. If it is stuck open you might be able to clean it with some carb cleaner in a spray can, but it will just get stuck again. You might solve your problem temporarily by just disconnecting it. The engine wont care if it's not working, just pull the vacuum line off and plug it with a small screw or golf tee.

Jan 18, 2011 | 1993 GMC Safari

1 Answer

What is DTC code P1491? 1997 Honda Accord


hi, "EGR Valve Lift Insufficient Detected" is most often caused by a broken vacuum line going to the EGR valve. So I would check all the vaccum lines to be sure they are tight and not broken.If the vacuum lines are good, you will need to check the electronics that operate the EGR system. thanks

Oct 26, 2010 | 1997 Honda Accord

2 Answers

1998 dodge ram error code 1494 check engine light on and poor gas mileage


Check all tubing and junctions for leaks in the fuel evaporation control system. The ECU has detected an issue with intake manifold pressure and is indicating that fuel vapour recovery system is perhaps to blame. Sometimes this can be connected to a fault in the manifold differential pressure circuit which lies on the vacuum line leading to the EGR valve. Also quickly check that the EGR (exhaust gas recirculation) valve is OK by connecting and reconnecting its vacuum line and listening to engine note changes. No engine note change indicates the EGR is probably jammed shut with exhaust crud and needs a general clean up. Sometime these codes detect the symptom and not the cause so you just have to work your way back and eliminate what it might be.

May 07, 2010 | 1998 Dodge Ram 2500 2WD

2 Answers

Vaccum hose diagram for 97 chevy tahoe 5.7 liter


I have the diagram you need. If you send me your email I will scan it off and send it to you. outdoorsman592003@gmail.com

Sep 12, 2009 | 1997 Chevrolet K1500

1 Answer

Can anyone describe how to easily check if timing has "jumped" on a 1990 240SX? Or describe the EGR valve location. I'd also like to find a vaccum line diagram. Thanks!


everything you need to know you can find by subscribing to All Data DIY. There is a fee, but trust me, it is well worth it. All Data is what repair garages and mechanics use.

Feb 25, 2009 | 1990 Nissan 240SX

Not finding what you are looking for?
1996 Ford Taurus Logo

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...