Question about Nissan Pathfinder

Open Question

2003 NISSAN NAVARA HIGH IDLE 1500 TO 1800 RPM. NO FAULT CODES PRESENT. COULD IT BE THE THROTTLE POSITION SWITCH.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
mrgreenz
  • 962 Answers

SOURCE: 2002 NISSAN SENTRA GXE 1.8 POOR IDLE LACKS POWER IDLE FLUCTUATES BETWEEN 1800 TO 1100 RPM

Check for vaccume leaks and also you PCV valve. check the hose too. Visually inspect every vaccume hose you can find. Sounds like a leak .

Posted on Nov 10, 2008

Ad
  • 1 Answer

SOURCE: High idle speed- Nissan N16 Pulsar/ Almera

Battery not charging well when airconditioner on ( also engine speed not increase when air conditioner on )

Posted on Jul 30, 2009

  • 1 Answer

SOURCE: 2003 nissan sentra se-r spec-v, started idle

i had a similar problem a few months ago with my se-r. i went to the dealership and had them reprogram the ecm and it fixed it(its on the recall list for your car.) once i did that everything ran great.

Posted on Aug 25, 2009

  • 1244 Answers

SOURCE: Car cuts out at idle

idle control valve. bad plug wires and bad plugs will all cause that as well as a air leak in the vacumn hose on galant

Posted on Jan 21, 2010

  • 1 Answer

SOURCE: nissan navara timing chain marks

I have a Nissan Nivara With the Z24 motor Fitting a new timing chain sprokets guides and adjuster Where does the camshaft numbers 1 2 and3 go

Posted on May 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why high rpm when slowing down?


huok up a scanner to check for sensor faults, if no codes present check your throttle linkage for binding as to not return to idle position

Oct 15, 2015 | Cars & Trucks

1 Answer

How do i fix?


P0122 throttle/pedal position sensor/switch A circuit low input
P0223 throttle/pedal position sensor/switch B circuit high input
P2101 throttle actuator ctrl motor circuit rang/perf
P2104 throttle actuator ctrl sys-forced idle
P2110 throttle actuator ctrl sys-forced limited rpm

Here is the meaning of the codes hope this helps

Sep 20, 2015 | Cars & Trucks

1 Answer

Lancer 2003 1.6; Wich Idle RPM, engine stall whenever aircond compressure clush was energized. and very vibration when transmission D was selected. Another component wich concern; New igniter plug...


Your idle problem could be caused by the EGR Valve, the Idle Air Control Valve, or the Throttle Position Sensor, or the Mass Airflow Sensor.Because there are so many things involved, you need t have the computer scanned for codes. The codes will tell us which of these components might be at fault. There are a few things you can do that might help. Make sure there are no vacuum leaks such as loose or damaged vacuum hoses. Make sure the air filter is clean. Get some Throttle Body Cleaner and clean the throttle body and the Idle Air Control Valve. Don't try to adjust the idle speed. It is controlled by the computer. Unless of course, you have had the throttle body and linkage removed from the engine, which could have caused the throttle linkage to be out of adjustment. You could try turning the adjusting screw to get the idle rpm up to around 700 rpm. But most likely, the computer will override any thing you do in that area.

Feb 22, 2011 | 2002 Mitsubishi Lancer

4 Answers

High idle speed- Nissan N16 Pulsar/ Almera


Battery not charging well when airconditioner on ( also engine speed not increase when air conditioner on )

May 30, 2009 | Nissan Pulsar Cars & Trucks

1 Answer

2003 nissan altima rpm goes crazy (at 2 then drops to 0, back and forth)then it dies. it is doing it more frequently


I have also read in the service manual that doing an idle relearn helps with RPM problems. This is the procedure below. It is complicated to do unless you have a watch or something to count the seconds with.

DESCRIPTION
“Accelerator Pedal Released Position Learning” is an operation to learn the fully released position of the accelerator
pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time
harness connector of accelerator pedal position sensor or ECM is disconnected.
OPERATION PROCEDURE
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch “ON” and wait at least 2 seconds.
3. Turn ignition switch “OFF” wait at least 10 seconds.
4. Turn ignition switch “ON” and wait at least 2 seconds.
5. Turn ignition switch “OFF” wait at least 10 seconds.
Throttle Valve Closed Position Learning UBS002OA
DESCRIPTION
“Throttle Valve Closed Position Learning” is an operation to learn the fully closed position of the throttle valve
by monitoring the throttle position sensor output signal. It must be performed each time harness connector of
electric throttle control actuator or ECM is disconnected.
OPERATION PROCEDURE
1. Make sure that accelerator pedal is fully released.
2. Turn ignition switch “ON”.
3. Turn ignition switch “OFF” wait at least 10 seconds.
Make sure that throttle valve moves during above 10 seconds by confirming the operating sound.
Idle Air Volume Learning UBS002OB
DESCRIPTION
“Idle Air Volume Learning” is an operation to learn the idle air volume that keeps each engine within the specific
range. It must be performed under any of the following conditions:
 Each time electric throttle control actuator or ECM is replaced.
 Idle speed or ignition timing is out of specification.
PREPARATION
Before performing “Idle Air Volume Learning”, make sure that all of the following conditions are satisfied.
Learning will be cancelled if any of the following conditions are missed for even a moment.
 Battery voltage: More than 12.9V (At idle)
 Engine coolant temperature: 70 - 95ーC (158 - 203ーF)
 PNP switch: ON
 Electric load switch: OFF
(Air conditioner, headlamp, rear window defogger)
On vehicles equipped with daytime light systems, set lighting switch to the 1st position to light
only small lamps.
 Steering wheel: Neutral (Straight-ahead position)
 Vehicle speed: Stopped

Apr 29, 2009 | 2003 Nissan Altima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

431 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...