Question about 2004 Kia Sedona

1 Answer

I Lost the Brake Fluid Cap 2 weeks ago on my van. I now have a new cap (had to wait for dealer to get it) after replacing cap, bleeding left rear brake, I started car and pedal goes to the floor. Any suggestions on how to bleed the entire system to clean it out and remove air, water, dirt?

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 370 Answers

You should be able to rent from your auto parts store a brake bleeding kit( auto zone, pep boys, or a store like that). It will hook up to one bleeder valve at a time, and then pull the fluid( using a vacuum pressure) to pull fluid to each caliper. You HAVE to keep a close eye on the fluid level in the fluid reservoir for the brakes( or get air back in the system). You will be able to do each one and solve your problem. Try this first, and let me know. Hope this helps.

Posted on Dec 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 01 GMC Jimmy 4.3L 4WD & we are trying to bleed the brakes but the scanner says my vehicle is going 3MPH so we manually bleed the brakes but the pedals still easily is pushed to the floor.


Bad master cylinder . What are you using a scan tool for ? No need Unless your Installing a new Electro-Hydraulic Control Unit (EHCU) or new Brake Pressure Modulator Valve (BPMV).
Hydraulic Brake System Bleeding (Manual)
Caution: Refer to Brake Fluid Irritant Caution in the Preface section.
Notice: Refer to Brake Fluid Effects on Paint and Electrical Components Notice in the Preface section.
Place a clean shop cloth beneath the brake master cylinder to prevent brake fluid spills.
With the ignition OFF and the brakes cool, apply the brakes 3-5 times, or until the brake pedal effort increases significantly, in order to deplete the brake booster power reserve.
If you have performed a brake master cylinder bench bleeding on this vehicle, or if you disconnected the brake pipes from the master cylinder, you must perform the following steps:
3.1. Ensure that the brake master cylinder reservoir is full to the maximum-fill level. If necessary add GM approved brake fluid from a clean, sealed brake fluid container. Refer to Fluid and Lubricant Recommendations.
If removal of the reservoir cap and diaphragm is necessary, clean the outside of the reservoir on and around the cap prior to removal.
3.2. With the rear brake pipe installed securely to the master cylinder, loosen and separate the front brake pipe from the front port of the brake master cylinder.
3.3. Allow a small amount of brake fluid to gravity bleed from the open port of the master cylinder.
3.4. Reconnect the brake pipe to the master cylinder port and tighten securely.
3.5. Have an assistant slowly depress the brake pedal fully and maintain steady pressure on the pedal.
3.6. Loosen the same brake pipe to purge air from the open port of the master cylinder.
3.7. Tighten the brake pipe, then have the assistant slowly release the brake pedal.
3.8. Wait 15 seconds, then repeat steps 3.3-3.7 until all air is purged from the same port of the master cylinder.
3.9. With the front brake pipe installed securely to the master cylinder, after all air has been purged from the front port of the master cylinder, loosen and separate the rear brake pipe from the master cylinder, then repeat steps 3.3-3.8.
3.10. After completing the final master cylinder port bleeding procedure, ensure that both of the brake pipe-to-master cylinder fittings are properly tightened.
Fill the brake master cylinder reservoir with GM approved brake fluid from a clean, sealed brake fluid container. Ensure that the brake master cylinder reservoir remains at least half-full during this bleeding procedure. Add fluid as needed to maintain the proper level.
Clean the outside of the reservoir on and around the reservoir cap prior to removing the cap and diaphragm.
Install a proper box-end wrench onto the RIGHT REAR wheel hydraulic circuit bleeder valve.
Install a transparent hose over the end of the bleeder valve.
Submerge the open end of the transparent hose into a transparent container partially filled with GM approved brake fluid from a clean, sealed brake fluid container.
Have an assistant slowly depress the brake pedal fully and maintain steady pressure on the pedal.
Loosen the bleeder valve to purge air from the wheel hydraulic circuit.
Tighten the bleeder valve, then have the assistant slowly release the brake pedal.
Wait 15 seconds, then repeat steps 8-10 until all air is purged from the same wheel hydraulic circuit.
With the right rear wheel hydraulic circuit bleeder valve tightened securely, after all air has been purged from the right rear hydraulic circuit install a proper box-end wrench onto the LEFT REAR wheel hydraulic circuit bleeder valve.
Install a transparent hose over the end of the bleeder valve, then repeat steps 7-11.
With the left rear wheel hydraulic circuit bleeder valve tightened securely, after all air purged from the left rear hydraulic circuit, install a proper box-end wrench onto the RIGHT FRONT wheel hydraulic circuit bleeder valve.
Install a transparent hose over the end of the bleeder valve, then repeat steps 7-11.
With the right front wheel hydraulic circuit bleeder valve tightened securely, after all air has been purged from the right front hydraulic circuit, install a proper box-end wrench onto the LEFT FRONT wheel hydraulic circuit bleeder valve.
Install a transparent hose over the end of the bleeder valve, then repeat steps 7-11.
After completing the final wheel hydraulic circuit bleeding procedure, ensure that each of the 4 wheel hydraulic circuit bleeder valves are properly tightened.
Fill the brake master cylinder reservoir to the maximum-fill level with GM approved brake fluid from a clean, sealed brake fluid container.
Slowly depress and release the brake pedal. Observe the feel of the brake pedal.
If the brake pedal feels spongy, repeat the bleeding procedure again. If the brake pedal still feels spongy after repeating the bleeding procedure, perform the following steps:
21.1. Inspect the brake system for external leaks. Refer to Brake System External Leak Inspection.
21.2. Pressure bleed the hydraulic brake system in order to purge any air that may still be trapped in the system.
Turn the ignition key ON, with the engine OFF. Check to see if the brake system warning lamp remains illuminated.
Important: If the brake system warning lamp remains illuminated, DO NOT allow the vehicle to be driven until it is diagnosed and repaired.
If the brake system warning lamp remains illuminated, refer to Symptoms - Hydraulic Brakes

Feb 26, 2017 | GMC Cars & Trucks

2 Answers

The front brake pads burnt and after replacing pads and calipers during bleeding the back lines have no problems. the front lines wont even push much air, and no sign of fluid, what should i do now?


Have you left the cap off the brake reservoir whilst bleeding procedure.if the cap is on between bleeding it won't allow fluid to flow out of bleed nipple.if it is still blocked then it sounds like the lines / pipes have debris in them so need flushing through or replacing.

Jun 20, 2015 | Cars & Trucks

1 Answer

How to bleed clutch 2007 compass


GRAVITY BLEEDING CLUTCH HYDRAULIC CIRCUIT

1. Verify fluid level in brake master cylinder. Top off with DOT 3 brake fluid as necessary. Leave cap off.

2. Raise vehicle on hoist.

3. Remove bleed port protective cap and install suitable size and length of clear hose (4) to monitor and divert fluid into suitable container.

4. Open up the bleed circuit by turning the thumb screw (3) counter clockwise this will start the air purge and fluid fill process.

5. Lower vehicle, but only enough to gain access to and fill the brake master cylinder. NOTE: Do not allow clutch master cylinder to run dry while fluid exits bleed port.

6. Top off brake master cylinder fluid level while air is purged and fluid drains from bleed port. Continue this until no air bubbles are seen and a solid column of fluid exists.

7. Close hydraulic bleed circuit, remove drain hose and replace dust cap on bleed port.

8. From driver's seat, actuate clutch pedal 60-100 times.

9. Apply parking brake. Start engine and verify clutch operation and pedal feel. If pedal feels fine and clutch operates as designed, stop here. If pedal still feels spongy or clutch does not fully disengage, excessive air is still trapped within the system, most likely at the master cylinder.

10. Top off brake master cylinder fluid level with DOT 3 brake fluid as necessary.

POWER BLEEDING CLUTCH HYDRAULIC CIRCUIT

1. Remove reservoir cap and connect bleeder cap to reservoir. NOTE: Use Bleeder Cap/Modified reservoir cap adapter Snap-on #901-059 or equivalent.

2. Connect service filling machine to bleeder cap. NOTE: Use Service Filling Machine/Brake power bleeder Brake power bleeder or equivalent.

3. Service filling machine should be pressurized to at least 2.5 bar (36 PSI).

4. Remove dust cap from bleeder valve and connect the transparent bleeder hose to bleeder valve.

5. Place the other end of hose in the bleeder container to capture the used fluid. The end of the hose MUST be submerged in the DOT 3 brake fluid.

NOTE: Use Bleeder Container To capture hydraulic fluid and Transparent Bleeder Hose To route fluid to container.

6. Turn on the service filling machine.

7. Crack open the bleeder valve (3).

8. Allow fluid to flow out of bleed port until no more air bubbles can be seen in the transparent bleeder hose.

9. Once fluid is free of air bubbles; make 15 quick actuations between clutch pedal stop positions.

10. Close the bleeder valve and disconnect the service filling machine.

11. To remove remaining air, actuate pedal 10 times slowly between pedal stop positions.

12. Check clutch pedal to see if vehicle is properly bled.

13. If vehicle is not properly bled, repeat procedure.

14. Remove bleeder cap from reservoir and replace reservoir cap.

15. Disconnect transparent bleeder hose from bleeder valve and replace dust cap.

Oct 15, 2013 | 2007 Jeep Compass Limited

1 Answer

1990 jeep wrangler bleeding breaks


Hi there:
I suggest to check this procedure, when the hydraulic brake system must be bled whenever a fluid line has been disconnected because air gets into the system.

A leak in the system may sometimes be indicated by a spongy brake pedal. Air trapped in the system is compressible and does not permit the pressure applied to the brake pedal to be transmitted solidly through the brakes. The system must be absolutely free from air at all times. If the master cylinder has been overhauled or a new cylinder has been installed, bleed the cylinder on a bench before installation. When bleeding brakes, bleed at the wheel most distant from the master cylinder first, the next most distant second, and so on. During the bleeding operation the master cylinder must be kept at least 3 / 4 full of brake fluid.


The ABS bleeding procedure is different from the conventional method. It consists of the following three steps:
Step 1: Conventional manual brake bleed.
Step 2: Bleeding the system using the DRB scan tool.
Step 3: An additional conventional manual brake bleed.

The recommended ABS bleeding procedure is as follows:
  1. To bleed the brakes, first carefully clean all dirt from around the master cylinder filler cap. Remove the filler cap and fill the master cylinder with DOT 3 brake fluid to the lower edge of the filler neck.
  2. Bleed the master cylinder first. Have a helper operate the brake pedal while bleeding each master cylinder fluid outlet line. Do not allow the master cylinder to to run out of fluid,as this will allow additional air to be drawn into the cylinder.
  3. Bleed the brake system in the following sequence:
    1. Master cylinder
    2. HCU valve body (at fluid lines)
    3. Right rear wheel
    4. Left rear wheel
    5. Right front wheel
    6. Left front wheel
  4. Clean off the bleeder connections at all four wheel cylinders. Attach the bleeder hose to the right rear wheel cylinder bleeder screw and place the end of the tube in a glass jar, submerged in brake fluid.
  5. Open the bleeder valve 1/2 - 3/4 of a turn.
  6. Have an assistant depress the brake pedal slowly and allow it to return. Continue this pumping action to force any air out of the system. When bubbles cease to appear at the end of the bleeder hose, close the bleeder valve and remove the hose.
  7. Check the level of fluid in the master cylinder reservoir and replenish as necessary.
  8. After the bleeding operation at each wheel cylinder has been completed, fill the master cylinder reservoir and replace the filler plug.

Do not reuse the fluid which has been removed from the lines through the bleeding process because it contains air bubbles and dirt.


  1. Perform the "Bleed Brake'' procedure with the DRB II scan tool. This procedure is described in the DRB II software information and diagnostic guide.
    1. Attach the DRB II scan tool to the diagnostic connector.
    2. Run the Bleed Brake procedure as described in the DRB II tester guide.
  2. Repeat the conventional bleeding procedure as previously outlined.
  3. Fill the master cylinder reservoir to the proper level.
  4. Check the brake operation.


Hope this helps.

Apr 21, 2013 | Jeep Wrangler Cars & Trucks

1 Answer

What are the proper steps to bleeding your brakes on a 1990 vw golf deisel


For left hand drive vehicles: (If the car does not have ABS system you do not need any diagnostic equipment!)

IMPORTANT NOTE: You need using diagnostic equipment connected to the data link connector of the car in order to bleed the ABS block. Follow instructions by scantool equipment for bleeding the ABS block.


1. This bleeding procedure requires two people. Remove the brake system reservoir cap, and fill up with new brake fluid until "MAX" level is reached.
2. Lift the car, or use a channel for access under vehicle.
3. Put the gearbox in "N" - Neutral position, or in "P" - Parking position for automatic transmission.
4. Start the engine and push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor.
5. Begin with the rear right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
6. Repeat steps no.#4 and no.#5 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

7. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
8. Continue with the rear left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
9. Repeat steps no.#7 and no.#8 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

10. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
11. Continue with the front right wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
12. Repeat steps no.#10 and no.#11 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.

IMPORTANT NOTE: All the time check the brake fluid level in the brake system reservoir, and fill up if necessary!

13. Push the brake pedal firmly for 4 - 5 times to the floor, and maintain the brake pedal pushed to the floor, engine idling.
14. Continue with the front left wheel. Another person remove the dust cap and loose the brake caliper bleeding screw until the brake pedal goes to the floor. At this moment maintain the brake pedal pushed to the floor, engine idling, and tight the brake caliper bleeding screw. Use a plastic hose: one end connected to the brake caliper bleeding screw, and another end inside a recovery bottle for used brake fluid.
15. Repeat steps no.#13 and no.#14 until no air flows through the brake caliper bleeding screw. Tight the brake caliper bleeding screw, and put the dust cap in their place.
16. Now the brakes are bleeded. Check the brake fluid level in the reservoir. Fill up with new brake fluid until "MAX" level is reached. Put back the brake reservoir cap.
17. Test the car brake system. The brake pedal movement no more than 1/3 of total stroke until the floor, when brake pedal is applied. Maximum admissible is 1/2 of total stroke.

Dec 06, 2010 | Volkswagen Golf Cars & Trucks

1 Answer

How do i bleed the brakes on a 1999 Pontiac Grand Am?


Bleeding the Brake System
When any part of the hydraulic system has been disconnected for repair or
replacement, air may get into the lines and cause spongy pedal action (because
air can be compressed and brake fluid cannot). To correct this condition, it is
necessary to bleed the hydraulic system so to be sure all air is purged.

When bleeding the brake system, bleed one brake cylinder at a time, beginning
at the cylinder with the longest hydraulic line (farthest from the master
cylinder) first. ALWAYS Keep the master cylinder reservoir filled with brake
fluid during the bleeding operation. Never use brake fluid that has been drained
from the hydraulic system, no matter how clean it is.

The primary and secondary hydraulic brake systems are separate and are bled
independently. During the bleeding operation, do not allow the reservoir to run
dry. Keep the master cylinder reservoir filled with brake fluid.


  1. Clean all dirt from around the master cylinder fill cap, remove the cap and
    fill the master cylinder with brake fluid until the level is within 1/4 I n.
    (6mm) of the top edge of the reservoir.
  2. Clean the bleeder screws at all 4 wheels. The bleeder screws are located on
    the top of the brake calipers.
  3. Attach a length of rubber hose over the bleeder screw and place the other
    end of the hose in a glass jar, submerged in brake fluid.
  4. Starting at the right rear proceed in this order left front, left rear and
    right front.
  5. Open the bleeder screw 1/2 - 3/4 turn. Have an assistant slowly depress the
    brake pedal.
  6. Close the bleeder screw and tell your assistant to allow the brake pedal to
    return slowly. Continue this process to purge all air from the system.
  7. When bubbles cease to appear at the end of the bleeder hose, close the
    bleeder screw and remove the hose.
  8. Check the master cylinder fluid level and add fluid accordingly. Do this
    after bleeding each wheel.
  9. Fill the master cylinder reservoir to the proper level.


prev.gif next.gif

Sep 21, 2010 | 1999 Pontiac Grand Am GT

1 Answer

Is there a special way to bleed the brake system on a 2001 catera


  1. Place a clean shop cloth beneath the brake master cylinder to prevent brake fluid spills.
  2. With the ignition OFF and the brakes cool, apply the brakes 3-5 times, or until the brake pedal effort increases significantly, in order to deplete the brake booster power reserve.

Fill the brake master cylinder reservoir with DOT-3 brake fluid from a clean, sealed brake fluid container. Ensure that the brake master cylinder reservoir remains at least half-full during this bleeding procedure. Add fluid as needed to maintain the proper level. Clean the outside of the reservoir on and around the reservoir cap prior to removing the cap and diaphragm.
  1. Install a proper box-end wrench onto the RIGHT REAR wheel hydraulic circuit bleeder valve.
  2. Install a transparent hose over the end of the bleeder valve.
  3. Submerge the open end of the transparent hose into a transparent container partially filled DOT-3 brake fluid from a clean, sealed brake fluid container.
  4. Have an assistant slowly depress the brake pedal fully and maintain steady pressure on the pedal.
  5. Loosen the bleeder valve to purge air from the wheel hydraulic circuit.
  6. Tighten the bleeder valve, then have the assistant slowly release the brake pedal.
  7. Wait 15 seconds, then repeat these steps until all air is purged from the same wheel hydraulic circuit.
  8. Repeat this procedure with the LEFT FRONT, then LEFT REAR and finally the RIGHT FRONT.
  9. Fill the brake master cylinder reservoir to the maximum-fill level with DOT-3 brake fluid from a clean, sealed brake fluid container.
  10. Slowly depress and release the brake pedal. Observe the feel of the brake pedal.

Feb 27, 2010 | 2001 Cadillac Catera

1 Answer

No brake fluid to the rear wheel cylinders


You'll need to start bleeding the brake system at the Master cylinder to determine where the problem lies.

The lines coming out of the master cylinder will need to be loosened & bled there, initially you can just do the back ones to identify the problem, but once fixed, the system will have to be bled from the Master cylinder first, then the farthest wheel from it, then next farthest, then next, until you do the drivers wheel last.

This method of bleeding the brakes prevents air from crossing from one line to another, causing air to be left in the system.

Back to bleeding the rear brakes first: As someone pumps up the brake pressure, making sure the resivoir stays full, with the cap on between bleeding, and have the person pressing the pedal to do these thngs.
1. Always move the pedal slowly, pressing and releasing.
2. Never release the pressure on the pedal after bleeding a brake, until the line is tightened, then release slowly to prevent air from getting into the fluid.

You should of course get fluid at the master cylinder when you bleed it (or just replace it), then you'll need to bleed the line at the right rear wheel (first) a few times to get fluid if it's been leaking, then the left rear wheel. If you get pressure but no fluid to the rear and the master cyliinder did have pressure released when you bled it, there is either a restriction in the line itself, or the porportioning valve could be damaged. (unusual for the valve to go bad actually, inspect lines for damage such as being pinched if you're getting pressure but no fluid.

Final test if it hasn't been resolved-remove lines at porportioning valve & make sure fluid is leaving/entering there as it should. If you find it defective, a good replacement can come from a salvage yard, or you can buy them new.

Brake fluid on the floorboard under the dash near the brake pedal=bad Master Cylinder.

good luck

Feb 21, 2010 | 1996 GMC Jimmy

3 Answers

What order do I bleed the brakes on a 2002 toyota sequoia


ALWAYS START YOUR BLEED PROCESS AT THE WHEEL FARTHEST FROM THE MASTER CYLINDER, WHICH IN YOUR CASE IS THE RIGHT REAR, THEN THE LEFT REAR, FOLLOWED BY RIGHT FRONT AND THEN LEFT FRONT.

Oct 21, 2009 | 2002 Toyota Sequoia

2 Answers

Brake line leak


start from the farthest, right rear, left rear, right front, then left front, take some time in bleeding your left front since it has more air induced during line replacement. good luck!

Oct 20, 2008 | 1990 Acura Legend

Not finding what you are looking for?
2004 Kia Sedona Logo

161 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

78238 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...