Question about 1997 Chevrolet Blazer

1 Answer

I have a '97 Blazer, the turn signals will not operate, fuse looks good, signal lights don't come. 4 ways work fine, assuming bulbs are ok. Is there another fuse somewhere to check????

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

You have a bad multi functional switch on the column. i have a 97 jimmy that did the samething. i had to replace the whole switch.

Posted on Dec 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 eagle talon hazard lights are not working in the rear. The turn signals don't work at all.


The first thing to check is the turn signal bulbs. Assuming those are OK, do the brake lights work? If they do, then double check the light assemblies nearby earth points. Run a wire from the battery (on the +12v on a tail light bulb) and test that the turn signal bulbs do light up. There could be dirt/corrosion in the bulb connector. If all that is OK, there'a failure in the wiring harness. Look under the carpet, driver's side for rust and harness corrosion.

Oct 19, 2017 | Eagle Cars & Trucks

1 Answer

How do i fix indicator lights on golf 4 2l. 2000 model. Bulbs is fine , bought a new relay , still not working.


Have you tested the turn signal switch is voltage leaving the turn signal switch? I would think it is the switch that is the problem assuming all the fuses related to the lights are ok and not blown out.

Aug 12, 2016 | 2000 Volkswagen Golf

1 Answer

What would cause turn signals,and flashers to stop working,and bulbs are good


bad earth to the ofending lights, burnt out flasher unit, worn switch. all assuming youv checked the fuse fisrt, after that check the flasher unit which should be in or near the fuse box and it will look like a rely so make sure youv got the manual or guide book befor you start pulling out the relays

Jul 30, 2014 | 1997 Mercury Mountaineer

1 Answer

97 Pontiac Trans Sport. Turn signal problem


verify the ground wire is good, black wire, its down on the frame rail, opposite of the air filter housing, if thats OK, it, could be the turn signal switch. but the wires go from the turn signal switch, through the Daytime Running Lights Module, through the fuse panel under the hood, then to the light socket. wire is light blue / white coming out of turn signal switch to DRL module, then its light blue all the way to the socket.

Oct 19, 2009 | 1997 Pontiac Trans Sport

2 Answers

No brake lights, turn signals, or 4-ways.


Did you actually check the bulbs? I believe your brake lights, signal lights, hazards all use the same bulb for each side.

Your brake lights may be your brake switch just above your brake pedal.
The signals could be your electronic flasher module (EFM) located under the dash near the steering column.
Your hazards may be affected by the EFM, but not likely and the switch for your hazards may be faulty

Sep 10, 2009 | 1998 Chevrolet Blazer

1 Answer

No rear turn signals, front turn signals light but dont flash


the problem is a bad flasher. $10.98 at advance auto. remove panels under steering wheel with 9/32 socket. It is hard to see turn blinker on to confirm it should tick each time. should take about 1/2 hour.

Jun 01, 2009 | 1999 Cadillac DeVille

1 Answer

Turning signals not working


The way the system works is:
The fuse supplies 12 volts to the flasher unit then leaves the flasher and goes to the turn-signal switch in the steering column.
When you set the turn-signal switch to turn right or left, the switch sends that 12 volts to the front and rear bulbs. The voltage goes through the bulb, lighting the bulb and goes to ground.
If any of these components are not good than the lights will not work.
Check the fuse and make sure it is good, the fuse will be located under the hood at the fuse center.
Let me know if you have a test light and we can proceed from there.
Regards,

May 09, 2009 | 2001 Chevrolet Blazer

3 Answers

No turn signals brake lights or hazard on 97 Blazer


did you check the bulbs and the fuses with a test light? If they are ok,try pressing the brake pedal, and wiggeling the 4-way flasher button at the same time....if the brake lights come on, it's in the 4-way flasher switch.

Aug 03, 2008 | 1997 Chevrolet Blazer

Not finding what you are looking for?
1997 Chevrolet Blazer Logo

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80668 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...