Question about Honda Accord

4 Answers

Brake pedal is mushy all the way to the floor. Have already replaced front calipers, master cylinder, and bled all the brakes. Pedal still goes all the way to the floor when stopping the car.

Posted by on

4 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 103 Answers

If the car has drum brakes in the rear, Jack the rear up and have someone push the brake pedal hard and you try to turn the wheel. If you can turn it you need to adjust the rear shoes. They may be traveling out so far that the fluid level drops causing the pedal to go to the floor. You must adjust them with the drum on till you hear and feel the shoes rubbing against the drum. Hope this helps.

Posted on Feb 01, 2015

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have soft paddle after changing rear calipers and master cilinder on honda accord se what do i need to do ?

Posted on Mar 01, 2013

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Honda Master
  • 715 Answers

Did you bench bleed the master cyl. before installing on the car ?

Posted on Dec 30, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 156 Answers

Not certain what types of rear brakes you have but sounds like a failed wheel cylinder on the rear. Suggest drums off and have a check

Posted on Dec 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1994 Jeep Grand Cherokee brake pedal goes all the way to the floor. Recently replaced calipers and master cylinder and bled the whole system. Brake pedal goes all the way to the floor when first pushed...


Not bleed properly
or you have a rusted out line (leak)

There is NO Procedure-- that when driving a
vehicle or bleeding brakes,do you ever pump them

Dec 03, 2014 | 1994 Jeep Grand Cherokee

1 Answer

2001 Silverado 2500 HD Why Rear brakes don't work after I installed new hydro-boost power booster, master cylinder, calipers, and pads. I bled master cylinder before installing, and brakes beginn


Hello Patricia,

Have you checked the master brake cylinder reservoir for brake fluid loss?

I don't suspect the master cylinder as you have replaced it... but am more suspect of a leaking brake line or fitting which should have
been discovered when you had the system bled.

The only time I ever had a rear brake problem with a 2500 series Chevrolet was due to seized rear brake caliper guide pins...as your calipers are also new that is not your problem.

If your brake pedal feels spongy and travels to the floor board you have air in the system, a brake fluid leak or a failure in the power steering system, such as a broken hose, broken power steering pump drive belt, or failed pump, would result in a loss of pressure to both the hydro-boost and steering.

Find more information here:

. Hydro Boost Power Assist Systems Operation Diagnosis and Repair

Jul 23, 2017 | 2001 Chevrolet Silverado 2500HD

2 Answers

Brake pedal goes to the floor


possible leak in brake system. if not then you have a bad master cylinder. have to replace it.

Aug 30, 2010 | GMC K2500 Cars & Trucks

1 Answer

2000 Chrysler Grand Caravan, replaced the front driver brake caliper, the brake lines from the master cylinder to the ABS and the rubber hose from the caliper to the brake line, bled all the brakes but the...


i suggest a bad master cylinder, but 1st answer this, when you apply brakes firmly and keep pressure on the brake pedal, does pedal go down while you're holding pressure on the pedal? if so, the master cylinders bad. and also have you checked the vacum to the brake booster?

Aug 24, 2010 | 2000 Chrysler Grand Voyager

1 Answer

Brake pedal goes to the floor


check vacumn and\or connections to the vacumn boost cannister.

Apr 21, 2010 | 1985 Ford F150

2 Answers

Brake pedel pushes to the floor


pump the pedal about 10 times and see if it comes back up, u need to pump the caliper pistons out after a brake job.

Jun 27, 2009 | 1997 Ford F150 Regular Cab

3 Answers

Just replaced master cylinder on 1990 aerostar and bled the brakes, still the pedal goes to floor and i have no brakes


Did you bench bleed the master cyl. before installing it? then when you installed the new master, did you bleed all 4 points? If yes, then check all for points for leaking caliper/s and leaking wheel cylinder/s. If the van has ABS, check the valve body for a bleeder screw and see if air bleeds out of it. If you've checked everything twice and did everything right then your new master cyl. may be defective.

Apr 29, 2009 | 1986 Ford F 250

2 Answers

1989 Ford F350 2 wheel drive dually 460 ci gas motor


5 Inspect Brake Fluid Type Brake fluid loss or contamination grey_line.gif 10 Inspect Master Cylinder (Brake System) Worn or leaking brake master cylinder. grey_line.gif 11 Inspect Brake Power Booster Damaged booster vacuum line/check valve, or diaphram

Nov 24, 2008 | 1989 Ford F 350

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

391 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...