Question about Ford F-100

1 Answer

How to rebild carb and replace - F-100 Ford Cars & Trucks

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 145 Answers

You'll need to buy a rebuild kit for your specific model. The instructions with different kits vary from almost nothing to not much more than basic instructions. If you want complete step by step instructions, then you should buy a Haynes or Chiltons repair manual for your specific vehicle. Rebuilding a carb is really not that hard and with a good repair manual, you'll be handy at it right away.
Some public librarys have a section with repair manuals for many of the more common vehicles.

Posted on Dec 30, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Fault code p0715 this code apairs allways before repair & after

if you have replaced the speed sensor then i would think the problem lies in the wring as you seem to think also, you could try to fault find the problem or just change the wiring harness , both i would imagine are a laborious task , i would start removing the harness , paying close attention where each connector goes and as removing harness check for any damage etc you may find the problem wire/connector before you get harness completely out ,if no visable fault carry on with the new replacement. This code is triggered when NO signal is received by the ECU/PCM , so a close inspection of the speed sensor wiring and mounting would be the first step , good luck

May 14, 2014 | 2007 Mercedes-Benz ML 320

1 Answer

How to time injecter pump chev 6.5 turbo diesel after engin rebild

Come back with the following info. Cam belt, gear driven, inline pump, rotary pump, common rail and I may be able to help as everthing is different for each set up

Feb 03, 2013 | Cars & Trucks

1 Answer

How to replace seal on steering gearbox,1983 suburban 1/2ton 4x4

If its liking from where the 4 scrwes are? U just remuve those 4 nuts, clean the cap and the gearbox, and install th new seal. If is liking from semewhere alse. It will be an O-ring and u have to take it all appart and rebild it. The new gearbox cost only$90.00 u can replesed th whole thing better. Good look

Nov 23, 2011 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

No spark after rebilding moter

well you didn't say what year it was , keeping that in mind I will try to respond with the info you did give. Generally the Chevy vans have a coil mounted in the distributor itself, so having spark comming from the coil would mean it is not flowing through the rotor to the plug wires..... not sounding right to me either,... Possibly just a bad Distributor cap unless you have already replaced it. So I would have you look at the Ignition module first and the pick up coil second.. not mush else it could be ( ruling out a broken timing chain ) If it is a newer vehicle , it may have a crank position sensor failing or ecm.

Oct 28, 2010 | 1996 Chevrolet Monte Carlo

1 Answer

How much are piston rods or a rebild kit

you may want to get an *** import motor as it will be much cheaper than a rebuild,especially if youre not keeping the car for 7 or 8 years,rebuild will cost $1,550 plus a whole decent engine will cost $500 or so

Sep 21, 2009 | Toyota Paseo Cars & Trucks

1 Answer

Transmission surges win it shifts When you take off it runs fine, until it shifts gears and then it starts jerking will bad. Let of the gas and excellerate again it run fine.

Hi , you need to change the oil filter in the auto drive and use a good type oil ie elf matic If the oil is black or very dark exspect to have a rebild, the oil should be changed every 12 monthes to keep the box in tip top condition.
Regards Andy

Sep 03, 2009 | Pontiac Grand Prix Cars & Trucks

1 Answer

Test for fuel cut off relay

Sam so right now you have crank no start,or no crank , no start. Not clear.
If its no crank no start.Your looking at battery, cables, ignition switch , starter relay.
If its crank no start, you know that B+ is making it to starter. Ok now listen for fuel pump to buzz or hum when you put key in ignition and turn to on position. No buzzing or humming fuel pump or relay.
make a set of jumper cables run them from battery to fuel pump, Does the pump run? If yes. The pump is good relay is not. If pump doesn't run then its the pump. Remember when you do this test you don't need the key in ignition Battery doesn't have to be connected, because your bypassing the control circuit.

Jan 24, 2009 | 1987 Honda Prelude

2 Answers

Car only drives in reverse. When we put the automatic transmission in drive, the engine just revs but doesn't go anywhere.

This is most likely a major problem such as a broken band in the tranny. Sorry.

Thank You for using Fix Ya!

Aug 24, 2008 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers


Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides