Question about 1996 Mazda Protege

Open Question

Changing a water pump on a 1996 madza protege 1.5 liter 4 cyl

How hard is it to change a water pump on a 1996 madza protege? And will I need to change the timing belt as well

Posted by on

6 Suggested Answers

  • 73 Answers

SOURCE: madza protege

748b22e.gif66bc404.gif this

Posted on Sep 10, 2008


CRTN
  • 716 Answers

SOURCE: timing belt on my 2002 hyundai accent 1.6 liter 4cyl

Was It Starting Before?
Who Changed It?

If The Belt Broke And The Belt Was Just Put Back On Without It Being Put In (TDC) Top Dead Center The Car Will Not Run. Warning! Trying To Start It Over And Over Will Destroy The Engine.The Engine Works By Being (TDC) Top Dead Center The Timing Controls When The Cylinders Come To The Top. The cylinders Are Controlled By The Timing So When The Spark Plugs Try To Ignite. The Cylinders Are Not In Position And Thus Will Not Create Combustion For The Engine To Run.

Posted on Jan 23, 2009

  • 334 Answers

SOURCE: Need confirmation that 5 Speed Transmission out 1993 Mazda Protege SOHC 1.8 liter Will Bolt up to the Same L-4 Block Engine /Mounts in the 1990 Mazda Protege LX 1.8 liter DOHC

try calling a junkyard and see if they will tell you the enterchange ok good luck

Posted on Apr 18, 2009

  • 5 Answers

SOURCE: Timing belt. 1990 2.3 liter 4 cyl. Crankshaft

there should be a mark on the crankshaft pulley there should be a mark on the camshaft pulley and they should line up but to be sure bring the motor to tdc then line your mark up on your camshaft

Posted on Aug 26, 2009

ronald_kate_
  • 111 Answers

SOURCE: timing belt on 1996 mazda protege slips during startup

Hello, this to me sounds like your fan belt slipping (not timing belt). To adjust the fan belt you need to undo your bolt on the alternator, pull it tight onto the fan belt and while holding it tight do the bolt back up tightly. this will stop yoour fan belt from slipping. I hope this helps.

Posted on Nov 06, 2009

  • 1075 Answers

SOURCE: timing marks on a 1996 ford escort 1.9L SEFI 4 cyl

im asuming all repairs went well,one,get a clean rag and wipe the gears and i mean wipe them clean two wipe and clean the plates behind them, three,lets start at the top find the dots on the gear you will see a tiny dot/indent four, look at the plate/caseing behind it and you will see another dot/indent,line them all up GEAR DOT to BACK DOT,five keep them in line and dont move them once you a satisfied all is in place and lined up and i mean lined up there is no room for error,fit belt and tighten .adrian,,,,,,,,

Posted on Aug 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change a waterpump in a madza protégé 2001 2.0


Not sure about your engine, but many today have water pump driven off the timing belt so you would have to remove timing belt covers for access. This is why when changing a timing belt most folks replace the WP also.

Jan 28, 2015 | Cars & Trucks

1 Answer

What happens if car doesn't start after changing timing belt mazda protege 1999


could be you did not get the timing marks lined up perfectly.
You will nee to verify that before doing anything else. (presume you reconnected all the electrical wiring correctly.)

Jul 30, 2014 | 1999 Mazda Protege

1 Answer

I need to change the water pump. i need to know where to look for it at on a mazda protege 1998


To get to the water pump on the Protege, you need to remove the timing belt also. This is not a job for the beginner, but if you are willing to give it a go, here is some info that you may find useful. CLICK HERE

May 02, 2011 | 1998 Mazda Protege

1 Answer

Need a diagram for 2000 madza relpacing timing broken belt.


Click on the following Link. It will take you directly to all the Diagrams you will need.
Before clicking, let me know if this helped you.

http://www.2carpros.com/car_repair_information/year/2000/make/mazda/model/protege/2000_mazda_protege_timing_belt_diagram_marks.htm

Feb 01, 2010 | 2000 Mazda Protege

1 Answer

How do you replace the water pump on a 1992 Mazda Protege?


Hi:

The water pump is driven by the timing belt, which is on the passenger side of your engine. You would need to remvoe all belts, and then the timing belt cover, and the timing belt to change your water pump.

Dec 02, 2009 | 1992 Mazda Protege

1 Answer

Timing Belt on 2002 Mazda Protege


every 90,000 to 100,000miles and yes it is strongly recomended to replace the water pump with it

Apr 02, 2009 | 2002 Mazda Protege

1 Answer

Timing belt 1998 Mazda Protege


Here's the AutoZone online manual page for timing belt and here's the page for the water pump.

Mar 09, 2009 | 1998 Mazda Protege

1 Answer

Water pump mx6


Buy a service manual, I just finished working on mine, it's a big job. You need to remove pass front wheel, plastic cover behind it, 2 belts of the pass side of the motor, motor mount, crankshaft pulley, timing belt covers, timing belt/tensioner, at this point you might be able to get to the water pump. Now get ready for the fun part of putting it all back on without making a mistake and destroying your engine. You can not get this done without a service manual. I know what I'm doing, and I probably could not do this without a book.

Jan 08, 2009 | 1993 Mazda MX-6

Not finding what you are looking for?
1996 Mazda Protege Logo

Related Topics:

436 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...