Question about 2001 Chevrolet Blazer

Open Question

Remove blazer high-mounted brake light - 2001 Chevrolet Blazer

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2003 chevrolet venture no left & right brake light

There is a fix for this problem on ebay

Posted on Dec 03, 2009

bbbman78
  • 680 Answers

SOURCE: replacing high brake light bulb 2003 blazer

It's mounted up on the roof and held on with a screw on each end. There's a sticky gasket under it to keep the moisture out. Remove the two screws (usually phillips head, but sometimes torx 20 or 25) and persuade it come (peel essentially) off. Pull it out slowly to reveal the plug and unplug it. It's an LED strip so the whole thing will have to be replaced. Easily located on a popular auction based web site for about $50.

Posted on Feb 28, 2010

Testimonial: "Thanks for your quick response, your answer is just as I suspected. I appreciate your help "

jsmes1027
  • 749 Answers

SOURCE: My brake lights dont work on my 2001 chevy blazer.

A very common issue with these is the multfunction/turn signal switch in the steering column.GM has a recall on this problem you should contact your local dealership have your VIN number to see if your vehicle is included in the campaign. If so the repair should be minimal cost or no charge to you at all.

Posted on May 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need a color code for the brake light wiring diagram for a 2000 s10 blazer


The S10 and the Blazer are identified as two different vehicles. The left stop light wire is YEL; the right is DK GRN. The center high mount stop lamp wire is LT BLU.

Oct 30, 2016 | 2000 Chevrolet Blazer

1 Answer

My brake lights dont work on my 2001 chevy blazer. Bulbs are good and fuzes are good. The center high mounted light above the rear hatch works fine. Just no other brake lights work. Any help?


A very common issue with these is the multfunction/turn signal switch in the steering column.GM has a recall on this problem you should contact your local dealership have your VIN number to see if your vehicle is included in the campaign. If so the repair should be minimal cost or no charge to you at all.

May 20, 2010 | 2001 Chevrolet Blazer

1 Answer

Drivers side brake light and horn won't work,,is it the multi function switch? 1999 chev blazer 4x4 . if so how much does a new one cost?


No there not connected, replace the brake light
1999 Chevrolet Blazer Auto Light Bulb Size Guide
Low Beam Headlight Bulb Size: 9006
High Beam Headlamp Light Bulb Size: 9005
Parking Light Bulb Size: 3157
Front Turn Signal Light Bulb Size: 3157
Rear Turn Signal Light Bulb Size: 3057
Tail Light Bulb Size: 3057
Stop Light Bulb Size: 3057
High Mount Stop Light Bulb Size: Assembly
Fog/Driving Light Bulb Size: 880 or 881
License Plate Light Bulb Size: 194
Back Up Light Bulb Size: 3156
Front Sidemarker Light Bulb Size: 194
Ash Tray Light Bulb Size: 161
Glove Box Light Bulb Size: 194
Map Light Bulb Size: 168 or 211-2
Step/Courtesy Light Bulb Size: 168 or 211-2
Trunk/Cargo Area Light Bulb Size: 211-2
Under Hood Light Bulb Size: 93
Instrument-General Light Bulb Size: 161 or 37 or PC194 or PC74
Check Engine Indicator Light Bulb Size: PC74
Hi-Beam Indicator Light Bulb Size: PC74
Seat Belt Indicator Light Bulb Size: PC194
Brake Warning Light Bulb Size: PC74
Automatic Transmission Indicator Light Bulb Size: 194
Directional Signal Indicator Light Bulb Size: PC74
As for the horn, inspect the fuse and relay and most common it would be a bad ground wire or worst a bad horn due to corrosion. Horn will be located in the drivers side fender.
Thank you for using fixya.

May 13, 2010 | 1999 Chevrolet Blazer

1 Answer

How do i change a brake light bulb on 2000 vw jetta?


Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Remove rear luggage compartment side panel trim (left or right).
98971821.gif
  • Remove 3 nuts, arrows, and remove housing.
  • Remove bulb holder.
Installing:
  • Install bulb holder.
  • Insert housing into body opening.
  • Tighten nuts.
  • Install applicable rear luggage compartment side panel trim.
Rear Light Bulb Holder Removing And Installing:
Removing:
  • Disconnect electrical connector.
  • Depress retainers, arrows, and remove bulb holder.
98971817.gif Installing:
  • Install in reverse order of removal.
And the Center Mounted Brake Lamp.
High mount Brake Light Removing And Installing:
The high mount brake light is installed in the rear shelf.
98971288.gif Removing:
  • Switch off all electrical consumers, switch off ignition key and remove ignition key.
  • Disconnect electrical connector from high mount brake light.
  • Remove rear shelf
  • Un-clip high-mount brake light from rear shelf, arrows.
  • Install in reverse order of removal.
NOTE: The bulb holder base plate contains soldered- in light emitting diodes (LEDs) that are not replaceable. In the event of LED malfunction, replace complete bulb holder.
Additional

Mar 13, 2010 | 2000 Volkswagen Beetle

2 Answers

Replacing high brake light bulb 2003 blazer


It's mounted up on the roof and held on with a screw on each end. There's a sticky gasket under it to keep the moisture out. Remove the two screws (usually phillips head, but sometimes torx 20 or 25) and persuade it come (peel essentially) off. Pull it out slowly to reveal the plug and unplug it. It's an LED strip so the whole thing will have to be replaced. Easily located on a popular auction based web site for about $50.

Feb 28, 2010 | 2003 Chevrolet Blazer

1 Answer

All lights work except stoplights could there be a solenoid for the brakes if so where is it?


brake light sitch on brake pedal may be at fault.the high mounted brake light has a seperate circuit from the regular brake lamps.so if you have no brake lamps the switch contols both circuits.give me a shout back.wish you the best.

Oct 24, 2009 | 2000 Chevrolet Blazer

1 Answer

High mount brake light works but the regular brake lights do not


Same circuit feeds both so I would check the bulbs by replacement and put a meter across the supply line

Oct 05, 2009 | 1997 Chevrolet Blazer

1 Answer

Replaceing brake lights on the trunk assembly part, how do i get to the lights?


High-Mount Brake Light NOTE: Depending upon the vehicle, the center high-mount brake light may be accessed from outside the vehicle, through the trunk, or through the passenger compartment.
  1. Remove the center high-mount bracket light lens retaining screws.
Fig. 17: Use a screwdriver to unfasten the center high-mount lens retaining screws . . .

0379160.jpg
Remove the lens in order to get to the bulbs.

Fig. 18: . . . then remove the lens for access to the bulbs

c49ad34.jpg
Carefully pull the bulb away from its retaining clip contacts.

Fig. 19: Pull the light bulb from the retaining clips

e0d87c6.jpg
Installation is the reverse of the removal procedure. Before installing the lens, make sure the brake light operates properly by having an assistant depress the brake pedal.

Jul 26, 2009 | 1999 Pontiac Bonneville

1 Answer

How do I replace the center brake light bulb on my 97 Oldsmobile 88?


High-Mount Brake Light NOTE: Depending upon the vehicle, the center high-mount brake light may be accessed from outside the vehicle, through the trunk, or through the passenger compartment.
  1. Remove the center high-mount bracket light lens retaining screws.
  2. Remove the lens in order to get to the bulbs.
  3. Carefully pull the bulb away from its retaining clip contacts.
  4. Installation is the reverse of the removal procedure. Before installing the lens, make sure the brake light operates properly by having an assistant depress the brake pedal.
I'll post the pics here in a sec.
Please don't forget to rate!!!!

May 07, 2009 | Oldsmobile 88 Cars & Trucks

1 Answer

Changing the bulbs in the window brake light


Here ya Go!

REMOVAL PROCEDURE
  1. Open the rear compartment lid.
  2. Rotate the high-mounted stoplamp socket(s) counterclockwise to release from the high-mounted stoplamp.
  3. Remove the bulb(s) from the socket(s).
INSTALLATION PROCEDURE
  1. Install the bulb(s) to the high-mounted stoplamp socket(s).
  2. Install the lamp socket(s) to the high-mounted stoplamp, then rotate clockwise to secure.
  3. Close the rear compartment lid.

Feb 11, 2009 | 2001 Chevrolet Lumina

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8202 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...