Question about 2006 Lexus Is 250

Open Question

Spark plug that is stuck inside of cylinder in lexus is-250

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: I WILL LIKE TO CHANGE

I need to change spark plugs on lexus sc 300 1992

Posted on Oct 19, 2008

  • 32 Answers

SOURCE: Change spark plugs on Lexus ES 250

No you can get to them by using an extension on your rachet with a rotating socket. Play around with the extension and rotating sockets to see which works best.

Posted on Dec 24, 2008

mkv0525
  • 358 Answers

SOURCE: cant find 3 of the spark plugs

under upper intake(plenium) on rear of motor. very tight fit.

Posted on May 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 Lexus IS 250 stuck in 3rd gear


That code has zero to do with the transmission issue. You have a mechanical failure in the tranny most likely, but have the TCM module scanned first before doing any parts replacement. P0171 is most likely an O2 sensor issue, it is indicating lean fuel.

Sep 13, 2016 | 2007 Lexus IS 250

1 Answer

How do i change the plugs and wires on a 1996 lexus ls 400


The spark plugs are located in well in the valve cover, remove them one at a time with a deep 5/8 good quality spark plug socket 3/8" drive on a 12 inch extension and a like sized ratchet. Remove the spark plug boot from the plug with a twisting motion side to side with the spark plug out remove the spark plug wire for that cylinder from the distributor cap and match it by length to the new wire in the spark plug wire set, make sure you get the closest one in length to the original wire, this is important. In stall the spark plug back into the valve cover well and attach the long plug boot to it in a twisting motion, use a little silicone grease on the inside of the boot to ease installation, it is supplied with the wire kit. Repeat this for each cylinder and match the individual wire lengths as you go as close as possible to the original wires. PLEASE NOTE: IF YOU FIND OIL ON THE PLUGS OR WIRE BOOTS THE VALVE COVER GASKET IS LEAKING INTO THE SPARK PLUG WELLS AND MUST BE REPLACED.

Oct 29, 2012 | 1996 Lexus LS 400

1 Answer

Where are the spark plugs located?


The sparkplugs are located inside the top of cylinder heads.if you follow the sparkplug wires to head you will see plugs. you will need to remove the top plastic engine covers to see them. good day

Feb 17, 2012 | 1991 Lexus LS 400

1 Answer

I have a 2001 Lexus rx 300 with a check engine light on with code P0301 cylinder 1 misfire. The spark plugs and ignition coils were already replaced. I swapped fuel injectors with known good cylinder and...


The minimum compression required is 95 psi, below this there is no good combustion, incusive the spark plug gets wet in gasoline
If this condition exists, you should check the piston rings and cylinder surface

May 20, 2017 | 2000 Lexus RX 300

1 Answer

How to change spark plug on lexuse gs300 2003


Hi, You need a new Spark Plugs Spark Plug Wrench Socket wrench Extension (At least 2-3 inch) size 10 socket size 12 socket...
First thing you need to do is find out where the spark plug cover is. Once you figure that out there will probably be size 10 or/and 12 bolts honding it down. Take that off and there you will see sensors connecting to each other and holding the spark plug in the cylinders. Unplug all the sensors and pull out the circular plugs holding the spark plugs down. THey might be a little tight and hard to get out so you're going to need to give it a good tug. Once you pull them out MAKE SURE YOU DONT DROP ANYTHING INTO THE CYLINDERS. You can look down into them and see the spark plugs. Get your spark plug wrench, extension, and socket wrench and stick them down in and push so that the spark plug wrench grabs them. Just simply unscrew the plugs, pull them all out, and then put the next ones in, and tighten them down. Just connect all the sensors, and put the cover back on and you're done. Pretty simple.
Take care

Jul 23, 2010 | 2003 Lexus ES 300

1 Answer

Oil pressure light is on and oil is on one of the


1st check quality oil and filter, if oil and filter is good, then remove engine oil pan , clean oil pump strainer, instal oil pan , add new oil and check.
if have oil on spark plug inside of cylinder, you need to overhaul the engine, if oil is over the spark plug ,change the valve cover gasket

Jul 20, 2010 | 1995 Lexus ES 300

2 Answers

Cant find 3 of the spark plugs


under upper intake(plenium) on rear of motor. very tight fit.

Apr 12, 2009 | 1990 Lexus ES 250

1 Answer

Change spark plugs on Lexus ES 250


No you can get to them by using an extension on your rachet with a rotating socket. Play around with the extension and rotating sockets to see which works best.

Dec 24, 2008 | 1991 Lexus ES 250

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...