Question about 2008 Nissan Rogue

Open Question

Seat belt light stays on and seat belts are attached-How do I get it to reset?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1779 Answers

SOURCE: Add middle seat belt to make 3 seat belts on a bench seat?

I'll begin by saying I'm surprised there isn't a 3rd belt on a bench seat, but I think you are entering dangerous territory. There is an immense amount of engineering, testing, and development involved in seat belt systems. They are anchored very securely at points that are reinforced and designed to withstand a human body being thrown against the belt, transferring the energy to the anchors of the belts. So, besides being beyond the scope of being possible to install by your average mechanic, I shudder to think of the legal angle. If u were to be involved in an accident, and someone was injured or worse in that seat wearing the added belt, the lawsuit possibilities are scary. Having said all this, check with your local dealer, maybe the Durango is set up somehow for an extra belt, but I've never heard it before.

Posted on Oct 13, 2008

Ad
  • 4 Answers

SOURCE: Seat belt problem

In my past experience with wiring in a car and seat belt lights I have found that most every newer vehicle will have a single negative lead wire running to some sort of switch in the seat belt locking mechanism. When the male end of the belt is placed into the female lock the switch will be depressed and grounded to complete a circut then turn off the light. If any switch is damaged and does not complete the circut then the light will not turn off. This may be the problem but it could also be a simple computer glitch in your vehicle. Another problem could also just be a blown fuse that triggers the light to come on as a precaution. A call to your local auto parts store may be able to help you more. I am just a self learning mechanic and not very computer savy.

Posted on Oct 31, 2008

hiseyj
  • 99 Answers

SOURCE: adjust the pre tensioner on the seat belt

It is not adjustable.

Posted on Nov 29, 2008

  • 29 Answers

SOURCE: automatic seat belt removal and replace with regular seat belts

You'd need to pickup the need parts at the junkyard. You'll need the "A" to "B" pillar trim, lower "B" pillar trim, front seat belts and seatbelt giude from a 1995 SC1 or SC2.

The treaded hole in the frame of the car where the track of the automatic seatbelt assembly attaches is in a slightly different place than the three point system. Its not a problem though. You just need to drill a 3/4" hole slightly above the existing hole in the trim panel. The existing hole is hidden by the seatbelt and not noticable at all.

Everything else pretty much bolts or snaps into place.

I've done this swap on several 1991-1994 Saturn S-Series.

Posted on Jan 27, 2009

  • 840 Answers

SOURCE: seat belt release

you nee to replace the seat buckle and possible the tensioner/ the seat belt buckle is easy to replace its a torx screw 32 bit take it out and replace /disconnect the battery when removeing/ to check seat belt tensioner pull out see if it goes back like a yoyo and if it does then you may not need the tensioner/ Please rate my response Thank you

Posted on Jan 31, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2009 Chevy Impala LT code b001b What to do with this?


Code B001b is for Sensing Diagnostic Module (SDM) for Air bag.

Potential Causes:-
  • Drivers Seat Belt Anchor Pretensioner
  • Passengers Seat Belt Anchor Pretensioner
  • Sensing Diagnostic Module (SDM)
  • Sensing Diagnostic Module (SDM) Wiring
1. Confirm the passenger seat belt anchor pre tensioner connector position assurance is clicked into place.

2. If not, click it in and retest.

3. If the codes reset, disable the Supplemental Inflatable Restraint (SIR) system.

4. Substitute a 2.0 to 2.2 ohm resistor for the passenger seat belt anchor pretensioner. Refer to Tech Tips for a load tool.

5. Retest for the code to reset.

6. If the code resets, check for harness problems between the seat belt anchor pretensioner and the Sensing Diagnostic Module (SDM).
Tech Tips: At the beginning of the 2009 model year, the Impala began being equipped with two pre tensioners for the driver and two pre tensioners for the front passenger. The first pretensioner is still attached to the seatbelt retractor. The second pretensioner is attached to the anchor point for the seat belt.
A load tool can be fashioned from an 1157 light bulb and socket. Turn the bulb into the socket. Using an ohmmeter, determine which 2 wires have 2 - 3 ohms of resistance. Use those 2 wires as the load tool.

Mar 30, 2015 | 2009 Chevrolet Chevrolet Impala LT

1 Answer

How do I turn off the airbag light after accident and unlock the seat belts?


Hi Sam!

I'm Michael from Safety Restore. Our company specializes in resetting srs airbag modules and rebuilding locked and blown seat belts after accident. We use 100% OEM parts and offer Lifetime Warranty. Visit our online store to learn more.

Post Accident Restoration We reset airbag modules and repair seat belt...

$50 SRS Airbag Module Reset
$65 Seat Belt Retractor Repair
$65 Seat Belt Buckle/Pre-Tensioner Repair
$75 Seat Belt Webbing Reaplcement

Thanks!

Oct 14, 2014 | Cars & Trucks

2 Answers

Seat belt light stays


Pull on the belts out a few times
& see if the light goes off

Aug 21, 2014 | 2002 Chevrolet Impala

1 Answer

1988 Chevy 1500 pickup, seat belt light stays on, but the buzzer stops when the seat belt isengaged


The weight sensor in the seat is bad if this is the passenger seat. When you connect the seat belt, the sensor is disabled.

Sep 19, 2012 | Chevrolet C1500 Cars & Trucks

1 Answer

2003 ford escape seat belt warnign light


Probably no need to see an expensive mechanic. My seat belt warning light came on a few days ago when there were four people in the car and the rear seat belts weren't fastened (I thought that was why it lit up). However, the light came on and stayed on when I was the only person in the car. Logically, it suggested a bad connection somewhere, so I checked the connector under the passenger seat and made sure it was properly fastened together. I then sprayed a small amount of WD40 into the female clasps of both front seat belt connectors, clipped and unclipped the belts a few times and the light is now fine. Try it - it worked for my 2003 Escape.

Jun 03, 2012 | 2003 Ford Escape

2 Answers

Srs light come on


hi,send your car to dealer to scan the problem,maybe erase fault is require ,or you can found the exact defective part,ty

Mar 23, 2009 | 2002 Mercedes-Benz C-Class

1 Answer

Seat belt light keeps staying on


There is a sensor that makes a connection when the seat belt is buckled, that turn out the light, it is defective, replace the seat belt assembly or remove the bulb.

Nov 19, 2008 | Volkswagen Touareg Cars & Trucks

1 Answer

Seat belt warning light on. 01 VW Golf


More likely to be a sensor - check gsf (google it - german, sweedish, french car parts) for the seat belt sensor

Sep 08, 2008 | 2002 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...