Question about 1999 Mercedes-Benz E-Class

1 Answer

Came Shafts tightening torque for a E320CDI 2000

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Mercedes-Benz Master
  • 1,675 Answers

Hi i gather you are referring to the camshaft carrier /caps? these are set to 9nm hope this helps

Posted on Jan 01, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 forenza 2.0 cam shaft torque specifications


most likely the torque specs are the same as the other model engine that is in your manual just be sure to tighten them slowly and equally back in forth in small increments because those cam shafts can snap very easily

Jan 02, 2013 | 2008 Suzuki Forenza

2 Answers

Do I need to torque the cam shafts


If you are asking about the cam shaft bearing caps, the answer is a most definite YES! I can't remember the exact measurement but believe it should be 12nm.. When bolting down the shafts, hand tighten each cap, pulling the shafts down evenly and then when all caps are fully closed use a torque wrench to complete the job. Regards John

Mar 31, 2012 | 1999 BMW 318 ti

1 Answer

I replaced the lifters in my 2000 galant 2.4 L and i need to know what to torque the rocker arm shafts to.


1.5 and 1.8 engines:
* Install the rocker arm and shaft assemblies. Tighten the rocker arm shaft retainer bolts to 23 ft. lbs. (32 Nm).

* Check valve adjustment and install the valve cover. Tighten the valve cover bolts to 16 inch lbs. (1.8 Nm) for the 1.5L engine or to 29 inch lbs. (3.3 Nm) for the 1.8L engine.



2.0 engine
* Lubricate the rocker shaft with clean engine oil and install the rockers and springs in their proper places.

* Install the rocker shaft assemblies on the engine. Tighten the bolts gradually and evenly to 21-25 ft. lbs. (29-35 Nm).



2.4 engine

fa2bc50.jpg

Fig. Rocker arm shafts and components-2.4L engine



* Fit the rocker shaft springs from above and position them so that they are at right angles to the plug side. Install the rocker springs before installing the exhaust side rocker shaft and rocker arm assembly.

* Install the exhaust side rocker shaft assembly in the engine. Tighten the rocker shaft mounting bolts gradually and evenly to 23 ft. lbs. (32 Nm).
* Remove the lash adjuster retaining tools.
* Install the rocker cover and tighten the mounting bolts to 30 inch lbs. (3 Nm).

* Reinstall the spark plug wires to the spark plugs.



Hope helps.

Sep 06, 2010 | Mitsubishi Galant Cars & Trucks

1 Answer

DRIVE AXLE TORQUE SPEC FOR 1963 BUG


please be more specific as to what exactly your trying to tighten ?' do you mean the drive shafts ?? if so put some locktight on the threads first ,failing that some contact adhesive will do ,if you mean the big nuts in the middle of the wheels then make sure you have some copper grease on the splined shafts before you start ,then tighten the big nut to about 90 , no torque wrench then tighten with a rachet and using regulation snap on bar a **** on the bar will suffice they do not have to be tightened with a scaffold pole on the end of the bar

Mar 19, 2010 | 2001 Volkswagen Beetle

3 Answers

Torque converter will not turn after transmission bell housing bolts are tighten...what is wrong?


When installing a torque converter there are two separate steps for two separate shafts with two different sets of splines.You must first turn the torque converter when on the input shafts until you feel Both steps engage one at a time.And with each step the torque converter will go deeper into the bell housing.To tell if you have caught each of the steps correctly you will be able to easily turn the torque converter,even when the trans and engine are pulled up tight.There will even be a gap between the flex plate and torque converter.What ever you do don't use the starter to get the torque converter all the way in.Take out the two bottom bolts of the trans and replace them with 1" longer ones.Then remove all the other bolts from the housing.Slide the trans as far back on those two bolts as you can until the torque converter will turn easily again,then turn while pushing in toward the trans until you feel the converter slip in that last step.Slide the trans back up to the engine and make sure the converter still spins freely,then finish your install.My first trans I literally broke the transmission housing by not fully seating the converter.Hope this helps?

Jan 01, 2010 | 1999 Ford Econoline

1 Answer

Need cylinder head gasket torque specs.


looks like there is special sequence to reassemble and tightening, a quick note replace any bolts that have two punch marks.tighten as follows: x x x x x 10 4 2 6 8 x x x x x 7 5 1 3 9 torque all down to 15 ft lbs torque to 30 ft lbs plus 90 degrees. Good luck!

Sep 18, 2009 | 2000 Ford Focus

1 Answer

Intake torque specs


Upper intake

Stage 1: Tighten to 20 Nm (14 lb-ft).
Stage 2: Tighten to 25 Nm (18 lb-ft).


Lower intake

Stage 1: Tighten to 15 Nm (11 lb-ft).
Stage 2: Tighten to 32 Nm (24 lb-ft).


Rocker Arms

Stage 1: Tighten to 10 Nm (89 lb-in).
Stage 2: Tighten to 32 Nm (24 lb-ft).

May 17, 2009 | 2000 Ford Windstar

2 Answers

I cant get the axle out of the front diff what is holding it in 2001 dodge durango


here is a diagram on how to get the front pinion seal out and it does mention how to get the axle loose. please do not forget to rate and comment about your experience with fixya today.
  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Remove both half shafts.
  3. Mark propeller shaft and pinion flange for installation reference.
  4. Remove front propeller shaft.
  5. Rotate pinion gear three to four times, to verify pinion rotates smoothly.
  6. Record pinion flange rotating torque with an inch pound torque wrench for installation reference.
  7. Hold flange with Holder 6719 and four bolts and washers.
  8. Remove pinion nut.
  9. Remove flange with Remover C-452.
  10. Remove pinion seal with a pry tool.
    67189-dako-g28.gif Removing the companion flange
    67189-dako-g25.gif Measuring pinion rotating torque
    67189-dako-g27.gif Pinion seal installer
    67189-dako-g26.gif Tightening the pinion nut
To install:
  1. Apply a light coating of gear lubricant on the lip of pinion seal.
  2. Install seal with Installer C-3972-A and Handle C-4171.
  3. Install pinion flange onto the pinion with Installer C-3718 and holder.
  4. Hold pinion flange with Holder 6719A.
  5. Install new pinion nut and tighten nut until there is zero bearing end-play.

    CAUTION Do not exceed the minimum tightening torque when installing the companion flange at this point. Damage to the collapsible spacer or bearings may result.
  6. Tighten pinion nut to 271 Nm (200 ft. lbs.).

    CAUTION Never loosen pinion nut to decrease pinion bearing rotating torque and never exceed specified preload torque. If preload torque or rotating torque is exceeded a new collapsible spacer must be installed.
  7. Record pinion flange rotating torque, with a torque wrench. Rotating torque should be equal to the reading recorded during removal plus an additional 0.56 Nm (5 inch lbs.).
  8. If rotating torque is low, tighten pinion nut in 6.8 Nm (5 ft. lbs.) increments until rotating torque is achieved.

    CAUTION If maximum tightening torque is reached prior to reaching the required rotating torque, the collapsible spacer may have been damaged. Replace the collapsible spacer.
  9. Install propeller shaft with reference marks aligned.
  10. Install half shafts.

Apr 16, 2009 | 2001 Dodge Durango

1 Answer

The seal on the front axle on the passenger side is leaking.is it hard to replace myself.


here is a diagram on how to replace the front pinion seal.
please do not forget to rate and comment about your experience with fixya.

  1. Before servicing the vehicle, please familiarize yourself with safety procedures.
  2. Remove both half shafts.
  3. Mark propeller shaft and pinion flange for installation reference.
  4. Remove front propeller shaft.
  5. Rotate pinion gear three to four times, to verify pinion rotates smoothly.
  6. Record pinion flange rotating torque with an inch pound torque wrench for installation reference.
  7. Hold flange with Holder 6719 and four bolts and washers.
  8. Remove pinion nut.
  9. Remove flange with Remover C-452.
  10. Remove pinion seal with a pry tool.
    67189-dako-g28.gif Removing the companion flange
    67189-dako-g25.gif Measuring pinion rotating torque
    67189-dako-g27.gif Pinion seal installer
    67189-dako-g26.gif Tightening the pinion nut
To install:
  1. Apply a light coating of gear lubricant on the lip of pinion seal.
  2. Install seal with Installer C-3972-A and Handle C-4171.
  3. Install pinion flange onto the pinion with Installer C-3718 and holder.
  4. Hold pinion flange with Holder 6719A.
  5. Install new pinion nut and tighten nut until there is zero bearing end-play.

    CAUTION Do not exceed the minimum tightening torque when installing the companion flange at this point. Damage to the collapsible spacer or bearings may result.
  6. Tighten pinion nut to 271 Nm (200 ft. lbs.).

    CAUTION Never loosen pinion nut to decrease pinion bearing rotating torque and never exceed specified preload torque. If preload torque or rotating torque is exceeded a new collapsible spacer must be installed.
  7. Record pinion flange rotating torque, with a torque wrench. Rotating torque should be equal to the reading recorded during removal plus an additional 0.56 Nm (5 inch lbs.).
  8. If rotating torque is low, tighten pinion nut in 6.8 Nm (5 ft. lbs.) increments until rotating torque is achieved.

    CAUTION If maximum tightening torque is reached prior to reaching the required rotating torque, the collapsible spacer may have been damaged. Replace the collapsible spacer.
  9. Install propeller shaft with reference marks aligned.
  10. Install half shafts.

Apr 12, 2009 | 2001 Dodge Durango

Not finding what you are looking for?
1999 Mercedes-Benz E-Class Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...