Question about Hyundai Tiburon

1 Answer

Need help in changing fog light in 2003 tiburon.I already have the lamp unplugged but can't seem to get the black plastic retainer piece off. Does it twist off? I need to get to the lamp asssembly underneath the black plastic retainer.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,382 Answers

Hi, all you have to do is jack up the car, remove the black plastic piece that blocks your view of the underside to see the light, unplug the wire (lift the top and pull down) then grab the plug area on the light and twist counter-clockwise. It should turn about 45-90 degrees (can't remember the exact) then pull out! Replace using the steps backwards..
I think the black plastic twist off and if it doesn't, then it is clipped.

Posted on Dec 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i replace fog light on picasso xsara 05


Jack up front; remove road-wheel (support Picasso on axle stand).

Remove two large torx screws on lower edge of bumper and peel back wheel arch liner (wedge behind hub).

Remove small torx screw holding black plastic support piece below lamp.

Remove 4 torx screws on holder surrounding lamp, pull back holder and support piece and lift out lamp (minding hands on broken glass)

Note that the body coloured bezel will try to fall outwards at this point.

Fit new lamp and push bezel in at the same time.

Refit all screws in reverse order, refit wheel etc.
(Total time 25 mins)

Aug 16, 2015 | 2005 Citroen Xsara Picasso

1 Answer

Change fog light n lense


Remove the plastic screen surrounding the fog light (held on by 3 Torx screws). Elevate the front of the car and remove the plastic tray under the front bumper(held on by 5-6 eight mm headed sheet metal screws).
Unplug the wire to the lamp and remove the four screws holding the fog lamp on.(4 Torx screws). You can't get a screwdriver into this tight space, so you'll need a torx bit and a 1/4" drive ratchet to turn it.
It is a tight work area and you'll have to take your time and just "worry" those screws out with the Torx bit..
Remove the lamp unit and replace it with the new one. reinstall four screws. Plug wire into the new lamp. Then reinstall the plastic splash tray under the bumper and the wire grill around the light. Done!

Mar 02, 2013 | 2008 Mercedes-Benz Mercedes Benz C Class

1 Answer

How hard is it to change a fog light bulb on a 2005 Subaru Forester? Can anyone do it?


Front Fog Light Assembly

REMOVAL


  1. Disconnect the ground cable from battery.
105919447



  1. Remove the two clips and lower mudguard on side that bulb is being changed.
  2. Disconnect the harness connector from bulb on back of fog lamp.
105919448




Front Fog Light Bulb

REMOVAL


1. Locate back cover on fog lamp assembly where bulb is located inside.

105919462



  1. Remove the back cover.
105919463



  1. Remove the spring retainer, and then detach the fog light bulb.
  2. DO NOT TOUCH HALOGEN BULB!! Oils from skin will cause bulb to explode during operation.

Jul 27, 2011 | Subaru Forester Cars & Trucks

1 Answer

How to change the fog lamp bulb on an audi a6 avant 2003


First remove the driver's side fog lamp plastic cover out from front bumper. After that you will find torx socket head panel screws from fog lamp. See picture below:


4958043.png

Jun 12, 2010 | 2003 Audi A6

1 Answer

How do I change my fog light bulb in my 1999 oldsmobile alero


YOU HAVE TO REMOVE FRONT SPLASH SHIELD TO REPLACE FOG LIGHTS.THEN YOU REMOVE THE TWO BOLTS RETAINING THE FOG LAMP TO THE BACK OF THE FRONT BUMPER REINFORCEMENT BEAM AND LOWER THE FOG LAMP.

Apr 30, 2010 | 1999 Oldsmobile Alero

1 Answer

Fitting single towbar electrics, Hyundai Coupe 2.0 2004 (Tiburon)


Hi There. Im not sure where you are but this is the sequence for the UK< Hope it helps.
here are the 7 cable locations and pin numbers.
Pin 1 Yellow L/H Direction Indicator
Pin 2 Blue Rear Fog Lamps
Pin 3 White Earth Return
Pin 4 Green R/H Direction Indicator
Pin 5 Brown R/H Tail & No, Plate Light
Pin 6 Red Stop Lamps
Pin 7 Black L/H Tail & No, Plate Lights

I found the easiest way to locate the correct wires in the loom is to turn on the lights required and use a circuit tester and splice into the main loom where you have enough wire to play with. Try not to cut the loom as it only causes more problems with bad connections and joins.(
Good Luck

Apr 16, 2010 | 2003 Hyundai Tiburon

2 Answers

How do you change the headlight bulb on 1996 olds delta 88? I cannot get to the bulb assembly.



REMOVAL & INSTALLATION

See Figures 1, 2, 3 and 4
  1. Disconnect the negative battery cable.
  2. Remove the fog lamp-to-bumper assembly retaining screws. Be careful not to disturb the adjusting screw.



0900c152800b1fa2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 1: Unfasten the 2 Torx® fog light retaining screws (1), making sure not to disturb the adjusting screw (2)
  1. Squeeze the bulb and socket assembly retaining clip prongs inward, and pull the bulb and socket from the rear of the fog lamp.



0900c152800b1fa3.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 2: Squeeze the bulb and socket retaining clip prongs inward ...


0900c152800b1fa4.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 3: ... then pull the bulb from the rear of the fog lamp
  1. Unplug the fog lamp electrical connector.



0900c152800b1fa5.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Fig. 4: Unfasten the fog lamp electrical connector
  1. Install the assembly, retaining bolts and connect the negative battery cable.


AIMING

  1. Park the car on a level surface, at least 25 ft. (7.6m) from a wall that is perpendicular to the ground surface. Make sure there is no excess weight in the trunk, unless you normally travel with that amount of weight in the car. Bounce the car a few times to settle the suspension.
  2. Measure and record the distance from the ground to the center of each fog light lens.
  3. Turn the fog lights on and adjust so the hot-spots (lit area of most concentrated intensity) are 4 in. (10cm) below the height of the lenses. The ADJUSTING screw is located at the top right corner of the fog light.

Jan 25, 2010 | 1996 Oldsmobile 88

1 Answer

Fog lights do not come on either when using headlights or with the fog lamp switch in my 2002 Grand Am SE. Fuse seems to be fine.


REPLACE THE FOG LAMP SWITCH DOWN ON THE STEERING COLM. REMOVE THE PROTEC. PANEL UNDER STEERING COLM. AND GENTLY START TO LOWER THE COLM. WATCH OUT FOR THE SHIFT IND. WIRE- REMOVE IT- LOWER COLM. AND HALF WAH DOWN ON THE TOP SIDE IS THE SWITCH FOR THE FOG LAMP CONTROL IF YOU HAVE ALREADY REPLACED THE ELEC. SWITCH - (PUSH BUTTON OR ROCKER STYLE ).IN THE DASH. IF - - LIGHTS AREON AND THE FOG LAMPS ARE TURNED ON AND THE HEAD LIGHT GO OUT OR WONT CHANGE FROM DIM TO BRIGHT REPLACE HIGH/LOW SWITCH ON COLM. SAME PROCEDURE AS FOG CONTOL SWITCH.

Nov 05, 2009 | Pontiac Grand Am Cars & Trucks

1 Answer

How do I change the tail lights on my hyundai tiburon 2003


Open your hatch and behind the tail lights you will see panels with plastic knobs you can unscrew. Behind there are 3 8mm nuts you need to unscrew which will let you remove the whole tail light assembly. There is a post on the actual tail light assembly that holds it in so you may have to give it a firm pull to actually seperate it from the car. If you have the stock infinity sub you will need to remove that first to get to the drivers side tail lamp.

Mar 19, 2009 | 2003 Hyundai Tiburon

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8266 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...