Question about 2000 Isuzu Rodeo

Open Question

How to get a FREE ENGINE MANUAL for Isuzu Rodeo 2000 2.2 petrol 4 cylinders

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is clutch slave cylinder located 2000 isuzu rodeo


down on the bell housing or on the engine block at the bell housing. Just follow the line from the master cylinder and you will find it.

Dec 02, 2013 | 2000 Isuzu Rodeo

2 Answers

Which cylinder do I use to set the timing in a 2.2L Isuzu rodeo?


All timing on engines is always done on Number 1 cylinder. On an inline engine it is the very front cylinder nearest to the radiator. On a transverse engine it is the cylinder nearest to the belt drive pulleys.

Feb 10, 2011 | 2001 Isuzu Rodeo

1 Answer

FIring Order of a 2004 Isuzu Rodeo 3.2L Engine


My apologies for the delay....Due to the bad economy the number of questions posted has skyrocketed 50% in the last 4-months.

For 2WD and 4WD it is the same:
For 3.2L:
Firing Order:
1-2-3-4-5-6
Cylinders:
5-------6
3-------4
1-------2
(front of vehicle)
Coil is on the Spark Plug

Let me know if this helped, or if you have additional information or questions. Feel free to contact me at FixYa.com!

Feb 06, 2010 | 2004 Isuzu Rodeo

1 Answer

Starter motor shot!


the starter assmelby is mounted near the gear box transmission system in most of the vehicle so see for it . as you mention the vehicle the vehicle is an SUV most of the SUV hold the starter motor near the Engine Gear box housing so see for it  or for more trouble free hazard free solution do see your nearest ISUZU or GM authorised service station...till then have safe driving & happy motoring see you soon sir...!

May 24, 2009 | 1994 Isuzu Rodeo

1 Answer

1997 isuzu rodeo


The firing order for a six cylinder is 1-2-3-4-5-6 distributor rotation-clockwise...cylinders 1-3-5 on drivers side...2-4-6 on passenger side

Dec 18, 2008 | 1997 Isuzu Rodeo

1 Answer

Overheated a 2000 isuzu rodeo 2.2 litre


  1. Sorry.... I did not see the 2.2 in title. Install the cylinder head with a new gasket. Tighten the bolts in sequence as follows: Step 1: 18 ft. lbs. (25 Nm)Step 2: Plus 90 degreesStep 3: Plus 90 degreesStep 4: Plus 90 degrees
    1. Step 1: 18 ft. lbs. (25 Nm)
    2. Step 2: Plus 90 degrees
    3. Step 3: Plus 90 degrees
    4. Step 4: Plus 90 degrees

Aug 24, 2008 | 2000 Isuzu Rodeo

1 Answer

Holden 94 rodeo petrol


Good Day
Vale clearance cold
intake .006 in (.15 mm)
exhaust .010 in (.25 mm)

Timing
1. With transmission in Neutral or park, start engine and warm to normal operating temp. turn eng,and all accessories off. connect Tachometer. Connect timing light to no 1 spark plug wire.

2. Disconnect and plug fuel vapor canister purge hose and EGR vacuum hose. Start and ensure idle is 900 RPM. adjust idle as required. Check ignition timing ( 12 @ 900)

3. If adjustment is required, loosen distributor hold down bolt and turn until timing is within specification. Tighten distributor hold down bolt and recheck timing. adjust idle speed as required.

hope this helps

Cheers

Aug 18, 2008 | 1994 Isuzu Rodeo

Not finding what you are looking for?
2000 Isuzu Rodeo Logo

Related Topics:

385 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76070 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...