Question about 2004 Chrysler Sebring

1 Answer

We have a 2004 Sebring. The heater fan does NOT work on positions 1 and 2 but DOES work on positions 3 and 4. I assume it is a coil resistor or a couple of coil resistors that are defective. My question is this. How do you get at these resistors???? Thank you

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 166 Answers

The twist knob swithc is bad or the heater controll box under dash that is the only two optins

Posted on Dec 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Honda Accord 2002 heater blower control works only in the high position. The 1, 2, and 3 positions do not work but the high (4) does.


The heater blower is normally controlled by voltage sent to the blower via a resistor network.
In this case it seems that this unit also called the fan resistor is defective.
I assume that 4 is the position where the blower is running HIGH and in this position the blower is powered directly without using resistor for lowering the speed of the blower. In step 1 - 3 the blower is powered via the mentioned resistor network.

In my opinion the resistor network is defective.
Replace it !!!!.

Jan 31, 2011 | 2002 Honda Accord

1 Answer

Heater blower on 2004 Sebring Convertible stopped working. I just replaced the heater resistor 3 weeks ago and all fan positions, 1, 2, 3, 4 worked awesome. I'm looking for a diagram for the interior fuse...


CHECK FOR VOLTAGE AT HEATER BLOWER MOTOR IF NOT YOU COULD HAVE A FAULTY BLOWER MOTOR RELAY.IF YOU HAVE VOLTAGE AT BLOWER MOTOR THEN BLOWER MOTOR FAULTY.

Nov 08, 2010 | 2004 Chrysler Sebring

1 Answer

2003 chev malibu blower fan not working in position #1,#2 ,#3.Works fine on #4,#5 Help please


its the heater fan resistor thats causing it. it has coils for different fan speeds, if a coil burns out or breaks. then you will loose that fan speed. to replace resistor, remove glove box to give ya more room so you dont have to stand on your head!! remove insulating panel under glove box. loosen and slide ecm to the side. now you can see heater blower fan, resistor is beside it, just remove wires , take out the hold down screws. and thats it!

Jul 26, 2010 | 2002 Ford Taurus

1 Answer

The fan for my Heater and A/C only works on the


there is a resistor for controlling the speeds and it needs to be replaced

Apr 27, 2010 | 2004 Chrysler Sebring

3 Answers

Heater fan only works on the high position?


There is a plug up under the glove box that loosens and you need to snug it up.

Dec 09, 2009 | 2004 GMC Canyon

1 Answer

Fan control dont work on 1 and 2 position 3 and 4 are ok


u need to check ur switch and after that if the blower is controlled by a resistor or not , if so have it check if the resistor is "open" or not

hope this helps
have fun

Sep 25, 2009 | 2004 Chrysler Sebring

1 Answer

Heater Problem: 2004 Chrysler Sebring Convertible


First off, time for a thermostat change if not done recently. Where does your temperature gauge ride when at normal operating temperature? Same as usual, or lower? As far as fan goes, sounds like fan resistor has gone and will need to be replaced. I'll double check to see if it's an inline resistor, or part of blower motor & get back to you. Are you planning on attempting all this yourself?

Feb 16, 2009 | 2004 Chrysler Sebring

2 Answers

2005 G6


If the heater fan on your car only works on "High" the problem is more than likely the resister assembly in your blower circuit or poor connections at the resister assembly. When the switch is in the "high" position the current does not flow through the resister assembly it flows directly to the coil of the blower relay. When the switch is in "low", "medium 1", or "medium 2" position the current flows through 1, 2, or all 3 of the resistors in the resistor assembly which results in the 3 different lower speeds. Check the resister assembly and replace if needed. 

Nov 25, 2008 | 2006 Pontiac G6

Not finding what you are looking for?
2004 Chrysler Sebring Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...