Question about 2000 Chevrolet S-10

Open Question

2001 s10 rear drum brakes do not have an open adjuster ports in order to release brake shoes to remove brake drum??

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
snownbird33
  • 120 Answers

SOURCE: Emergency Brake Loss

Good day;
After you put it all back together did you drive the car in reverse then apply park brake? If not give this a try, just use your hand park to stop the car, these should fix the problem,Let me know how you made out.

Cheers

Posted on Aug 27, 2008

Ad
tripletauto
  • 1450 Answers

SOURCE: 95 Lumina rear brakes/low pedal.

IT IS POSSIBLE THE WHEEL CYLINDERS are wrong and need too much fluid to push brakes out. or rear shoes are not adjusted correct. this could be from drums too big(unlikely since new) shoes are not fitting to drum correct.You can take shoes off and set them in drum the whole shoe should contact drum sometimes just the ends contact. If this is case sand off ends of lining to make it fit .
If wheel cylinders are bad they would leak. might try a different brand of cylinders.

Posted on Oct 08, 2008

  • 740 Answers

SOURCE: 96 Cavalier passenger rear brake lock up when wet or cold

Bad PROPORTION VALVE ... the back brakes should only be doing 30% of the stopping with a bad proportion valve it will send more pressure to the back during braking and cause it to lock up. Good Luck and thanks for using FIX YA

Posted on Jan 04, 2009

  • 23 Answers

SOURCE: parking brake adjustment

the parking brake is adjusted at the brake lever inside the car 10 mm nuts at the base of lever

Posted on Feb 24, 2009

  • 73 Answers

SOURCE: parking brake cable adjustment

if its rear shoes there is a cog wheel that turns in and out to close and spread the shoes just turn the wheel to make the shoes go in a little at a time and the drum will go back on

Posted on Mar 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Break peddle squeak when I release my foot on my hyundai coupe 1.6 2001


moe than likely the rear brakeshave worn...in order to remedy, issue may be 1 of 2 possiblities... easiest is to adjust the rear brakes, however, that is only the rear "drum" brake application and not in rear "disc" brake. Most Accents I've worked on had the "drum" brake application. Typically no more than $40. to do something like that.

If the adjustment is not taking care of the squeal, then rear brake replacement is in order. Either shoes (for drums) or pads (for disc)

Jun 19, 2015 | Hyundai Cars & Trucks

1 Answer

How to remove and clean and replace the rear brakes on a 2008Toyota yaris


REMOVING REAR BRAKE DRUM SUB-ASSEMBLY
1. Release the parking brake and remove the rear
brake drum.
If the rear brake drum cannot be removed easily,
do the following:-
2.Remove the hole rubber and insert a screwdriver
through the hole into the backing plate, and hold the
automatic adjust lever away from the adjuster.
3.Using another screwdriver, contract the brake shoe
by turning the adjuster.
4. Take out the brake drum from the flange.
5. remove the shoe hold down spring cup, shoe hold down spring, pin and front side brake shoe.
6. Remove the tension spring. Remove the shoe return spring from the rear brake shoe and remove the parking brake shoe strut set.
7. Remove the shoe holding spring cup, shoe hold spring, pin and rear brake shoe.
8. separate the parking brake cable.
9. Remove the automatic adjust lever tension spring and remove the automatic adjust lever.
10. remove the C-washer and remove the parking brake shoe lever.
NOTE: Do not use any solvent like gasoline to wash the brake parts.
Always wear safety goggles and mask before using compressed air.



Dec 28, 2013 | Cars & Trucks

2 Answers

Rear brakes


Removal
1.Remove rear wheel and tire assembly from vehicle.

2.Remove rear brake drums from hub and bearing assemblies after loosening the two brake drum screws.
bj6c017a.gif
3.Be sure that the parking brake pedal is in the release(most upward) position.

4.Completely loosen square nut of the rear parking brake cable. Then create slack in the rear parking brake cables.
bj6c017b.gif
5.Remove adjuster spring from adjust lever and brake shoe.
bj6c017c.gif
6.Remove adjust lever and turn the adjusting wheel of adjuster assembly to the direction of the arrow as shown.
bj6c017d.gif
7.Remove the strut spring and the lower retracting spring from the brake shoe.
bj6c017e.gif
8.Remove the upper return spring from the brake shoe.
bj6c017f.gif
9.Remove brake back plate hold down spring and pin from the leading brake shoe assembly.

10.Remove the leading brake shoe. Then remove the adjuster assembly, strut and anchor spring from the trailing brake shoe.
bj6c017g.gif
11.Remove the trailing brake shoe from the brake back plate after removing hold down spring and pin.
bj6c017h.gif
12.Remove the trailing brake shoe from the rear parking cable.
bj6c017i.gif
13.Remove parking pivot lever from the leading brake shoe.
bj6c017j.gif
Replacement
1.Lubricate the eight shoe contact areas on the back plate and anchor.
bj6c017n.gif
2.Install the trailing brake shoe to the rear parking cable.

3.Install trailing brake shoe on brake back plate and install the trailing brake shoe hold down spring and pin on the brake shoe.

4.Tighten the square nut of rear parking cable.

5.Install the anchor spring then install adjuster assembly, and strut.

6.Install leading brake shoe on brake back plate.
bj6c017o.gif
7.Install the brake shoe upper return spring, strut spring and the lower retracting spring to the brake shoe.

8.Properly rotate the adjusting wheel of adjuster assembly to the direction of the arrow in as shown.
bj6c017d.gif
9.Install the adjuster spring on the adjust lever and leading brake shoe assembly.

10.Install the leading brake shoe hold down spring and pin on the brake shoe.
bj6c017q.gif
11.Adjust brake shoes assemblies so as not to interfere with brake drum installation.

12.Install the rear brake drums on the hubs.

13.Check and adjust whether the pedal stroke in the specification.(Refer to section BR Gr./On-vehicle service/Pedal stroke of parking brake)

14.Install wheel and tire.

15.Push the parking brake pedal to the floor once and release pedal. This will automatically remove the slack from and correctly adjust the parking brake cables.

16.Test the vehiche on the road. The adjust will continue the brake adjustment during the road test of vehicle.

Inspection
1.Inspect the disassembled parts for wear, rust or damage.

2.Measure the thickness of brake shoe lining.
Standard : 0.17 in (4.5 mm)
Minimum : 0.04 in (1 mm)

3.If the shoe lining is less than minimum or shows signs of uneven wear, replace new one.
bj6c017k.gif
4.Measure the inside diameter of the brake drum.
Standard : 10 in (254 mm)
Maximum : 10.07 in (256 mm)
bj6c017l.gif
5.If the inside diameter of the brake drum is more than maximum or shows signs of uneven wear, replace new one.

6.Inspect the lining and drum for proper contact. If the contact condition is improper, repair it with a grinder or replace the brake shoe assembly.
bj6c017m.gif

Aug 14, 2013 | 2002 Kia Sedona

1 Answer

Adjust rear brakes on 2001 mazda tribute dx


Adjustments BRAKE SHOE ADJUSTMENT
  1. Remove the brake drum.

89219140


  1. Using the special tool, measure the inside diameter of the brake drum.

89219141


  1. Position the special tool on the brake shoes and linings and adjust accordingly.
  2. Install the brake drum.




Oct 07, 2011 | 2001 Mazda Tribute

1 Answer

I have a 2000 suziki grand vitara and cant furure out how to remove the rear drums


  1. Raise and safely support the vehicle.
  2. Remove the rear wheel(s).
  3. Release the parking brake.
  4. Remove the parking brake lever cover screws and loosen the brake cable locking nut.
  5. Install 2, 8mm bolts into the brake drum holes and uniformly tighten each bolt. Tighten each bolt until the brake drum is removed from the vehicle. If there is difficulty in removing the drum, insert a small tool through the hole in the rear of the backing plate, and hold the automatic adjusting lever away from the adjuster. Using another narrow, flat tool at the same time, reduce the brake shoe adjuster by turning the adjusting wheel.
If the drum is difficult to pull off using the bolts mentioned above, the parking brake is most likely the cause and will have to be adjusted "IN" to prevent drum to shoe contact.


ledsled378_171.jpg

Sep 20, 2011 | 2001 Suzuki Grand Vitara

1 Answer

How to change rear barke shoes


Brake Drums & Brake Shoes Removal & Installation To Remove:
Rear Drum Brakes kia-09-18-7627.gif

  1. Raise and safely support rear of vehicle.
  2. Release parking brake.
  3. Remove rear wheel assemblies. NOTE: If brake drum is stuck, install two 8 mm bolts into threaded holes and tighten evenly.
  4. Remove top return spring, front and rear shoe spring clips and hold-down pins.
  5. Remove anti-rattle spring and adjuster spring. NOTE: Note position of operating lever prior to removal.
  6. Remove bottom return spring.
  7. Remove clip and washer and detach parking brake cable from rear shoe.
  8. Remove brake shoes.
To Install:
  1. Lubricate all brake shoe contact points with appropriate grease.
  2. Place operating level into position on hub.
  3. Install rear brake shoe and connect parking brake cable to rear shoe with washer and clip.
  4. Install front brake shoe and install bottom return spring.
  5. Install hold-down pins and spring clips.
  6. Position operating lever and install top return spring.
  7. Install anti-rattle spring and adjuster spring.
  8. Install brake drum and screws.
  9. Adjust brakes and install rear wheel assemblies.
prev.gif next.gif

Jan 21, 2011 | 2003 Kia Spectra

2 Answers

Parking Brake


With the parking brake released go under the car and trace the parking brake cable s all the way the the rear brakes. If no problem is found jack the rear of the car up and remove the rear wheels. Remove the brake drums (you might have to insert a brake tool or screwdriver and loosten the adjustment in order to get the drums off. Inspect both brake systems for problems. If you drove through water on your last trip and the car was parked for several days the rear shoes sometimes get stuck to the drums because of rust. Water on the shoes can also cause the automatic adjustors to over tighten the shoes and adjusting the tension with the brake tool or screwdriver will correct it. Most of the time the adjustment slot is on the backplate at the bottom and has a small rectangular rubber plug you have to remove to make the adjustment. Some of the newer vehicles have the adjustment on the front of the drum and is a round hole which must be near the top to reach the adjustor.

Dec 29, 2009 | 2001 GMC Jimmy

1 Answer

Remove and replace rear brake shoes on 2004 honda accord


Brake Shoes Removal & Installation To Remove:
  1. Raise and safely support rear of vehicle.
  2. Remove rear wheel assemblies.
  3. Release parking brake.
  4. Remove brake drum.
Rear brake shoe assembly


6c57c70.gif
  1. Using an appropriate brake spring tool, unhook upper return spring from rearward brake shoe.
  2. Push retainer springs IN and turn to remove tension pins.
  3. Lower brake shoe assembly and remove lower return spring.
  4. Remove brake shoe assembly from back plate.
  5. Disconnect parking brake cable from lever and remove brake shoe.
  6. Remove parking brake lever from brake shoe.

To Install:

d36458c.gif
  1. Install parking brake lever to rearward brake shoe.
  2. Secure lever to brake show with a NEW U-clip.
  3. Pinch U-clip closed.
  4. Connect parking brake cable to rearward brake shoe.
  5. Install self-adjuster lever spring on front brake shoe.
  6. Assemble clevises, adjuster bolt and upper and lower return springs.
  7. Apply a light coat of grease (Molykote 44MA or equivalent) to sliding surfaces.
  8. Install brake shoe assembly onto back plate.
  9. Install tension springs.
  10. Using an appropriate brake spring tool, unhook upper return spring to rearward brake shoe.
  11. Install brake drum.
  12. Install rear wheel assembly.
  13. Lower vehicle.
  14. Adjust self-adjusting brakes by pressing brake pedal several times.

Jul 13, 2009 | 2004 Honda Accord

1 Answer

Loose emergency brake on 2004 Saturn Vue


  1. Apply and fully release the park brake several times. Verify that the park brake lever releases completely.
  2. Turn ON the ignition. Verify the red BRAKE warning lamp is not illuminated.
  3. If the red BRAKE warning lamp is illuminated, verify the following:
    • The park brake lever is in the fully released position and against the stop.
    • There is no slack in the park brake cable.
  1. Turn OFF the ignition.
  2. Disable the SIR system.
  3. Remove the front floor console.
  4. With the park brake lever in the released position, using ONLY hand tools, loosen the adjusting nut completely to the end of the front cable threaded rod.
  5. Raise and support the vehicle.
  6. Remove the rear tire and wheel assemblies.
  7. Adjust the rear drum brakes.
  8. Ensure there is no brake shoe drag after adjustment by rotating the brake drums. If drag exists, re-center the brake shoes and perform the brake shoe adjustment again.
  9. Install 2 wheel nuts to the wheel studs and firmly hand tighten in order to retain the brake drums.
  10. Lower the vehicle to permit access to the park brake lever.
  11. Raise the park brake lever 1 detent position. Notice: Refer to Fastener Notice in Service Precautions.

Jan 14, 2009 | 2004 Saturn VUE

1 Answer

Rear brakes scrubbing on 1998 chevy venture van


Removal Procedure Tools RequiredJ 38400
Caution: Keep fingers away from rear brake shoe springs to prevent fingers from being pinched between spring and shoe web or spring and backing plate.
  1. Remove the brake drum. Refer to Brake Drum Replacement

  2. 142285.gif
    tif.gif
    Notice: Do not over stretch the adjuster spring. Damage can occur if the spring is over stretched.
  3. Use the J 38400 in order remove the adjuster spring (1). Disengage the adjuster spring loop from the tab on the adjuster actuator.
  4. 2.1. Remove the loop end of the adjuster spring from the adjuster actuator. 2.2. Remove the straight end of the adjuster spring from the secondary brake shoe.
    142293.gif
    tif.gif
  5. Use the J 38400 in order to spread the brake shoes apart.
  6. Remove the adjuster.
Installation Procedure

    142293.gif
    tif.gif
  1. Use the J 38400 in order to spread the brake shoes apart.

  2. 178990.gif
    tif.gif
    Important: Ensure that the adjuster (2) engages the brake shoes (4 and 5), the park brake actuator (3), and the adjuster actuator (1) properly.
  3. Install the adjuster.

  4. 142285.gif
    tif.gif
    Notice: Do not over stretch the adjuster spring. Damage can occur if the spring is over stretched.
  5. Install the adjuster spring (1).
  6. 3.1. Install the straight end of the adjuster spring into the secondary brake shoe. 3.2. Install the loop end of the adjuster spring to the adjuster actuator.
  7. Install the brake drum.

Dec 06, 2008 | 1999 Chevrolet Venture

Not finding what you are looking for?
2000 Chevrolet S-10 Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...