Question about 1992 Cadillac DeVille

1 Answer

I have a blown return line to the steering pump, can i just replace that line flush the system and bleed it and be on my way or is there something else i need to do,

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 870 Answers

Nothing else to do. Good luck

Posted on Dec 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Getting ready to put new power steering pump on, but forgot to flush system, and can't find a line to Drane, So with out damaging the new one, HOW do I flush the system...??


Disconnect the return line from the pump and let it hang into a drain container. Start the vehicle and turn the wheel, this will evacuate old fluid into container. Stop engine and fill the reservoir with new fluid and repeat, this will flush the system. Reconnect the return line to the pump and add new fluid. Start the vehicle and turn the wheel slowly until its easy to turn and you don't hear any noise from the pump; this evacuates any air from the system

Feb 15, 2017 | Cars & Trucks

3 Answers

Steps for replacing pwr steering hoses on '94 3.1 Cutlass Supreme?


SERVICE PROCEDURE: THE POWER STEERING FLUID REPLACEMENT PROCEDURE IS A TWO-STAGE PROCESS: FIRST, FLUSHING THE OLD FLUID FROM THE SYSTEM WITH NEW FLUID; AND SECOND, BLEEDING THE SYSTEM TO REMOVE ANY TRAPPED AIR. THE FOLLOWING TWO SEQUENCES OUTLINE THE STEPS IN EACH PROCEDURE.

FLUSHING THE POWER STEERING SYSTEM 1. RAISE THE FRONT END OF THE VEHICLE OFF THE GROUND UNTIL THE WHEELS ARE FREE TO TURN.

2. REMOVE THE FLUID RETURN LINE AT THE PUMP RESERVOIR INLET CONNECTOR.

3. PLUG THE INLET CONNECTOR PORT ON THE PUMP RESERVOIR.

4. POSITION THE FLUID RETURN LINE TOWARD A LARGE CONTAINER IN ORDER TO CATCH THE DRAINING FLUID.

5. WHILE A SECOND PERSON FILLS THE RESERVOIR WITH NEW LOW TEMPERATURE CLIMATE SERVICE FLUID, START AND RUN THE ENGINE AT IDLE.

6. TURN THE STEERING WHEEL FROM STOP TO STOP.

NOTICE: DO NOT HOLD THE WHEEL AGAINST STOPS WHILE FLUSHING THE SYSTEM. HOLDING STEERING WHEEL AGAINST WHEEL STOPS WILL CAUSE HIGH SYSTEM PRESSURE, OVERHEATING, AND DAMAGE TO THE PUMP AND/OR GEAR. 7. CONTINUE DRAINING UNTIL ALL OF THE OLD FLUID IS CLEARED FROM THE POWER STEERING SYSTEM. ADDITION OF APPROXIMATELY 1 QUART OF NEW FLUID WILL BE REQUIRED TO FLUSH SYSTEM.

8. UNPLUG PUMP RESERVOIR INLET AND RECONNECT RETURN LINE.

9. TURN ENGINE OFF, AND FILL RESERVOIR TO THE "FULL COLD" MARK.

10. CONTINUE WITH FOLLOWING PROCEDURE "BLEEDING THE POWER STEERING SYSTEM".

BLEEDING THE POWER STEERING SYSTEM AFTER REPLACING THE FLUID OR SERVICING THE POWER STEERING HYDRAULIC SYSTEM, YOU MUST BLEED AIR FROM THE SYSTEM. AIR IN THE SYSTEM PREVENTS AN ACCURATE FLUID LEVEL READING, CAUSES PUMP CAVITATION NOISE AND OVER TIME COULD DAMAGE THE PUMP. TO BLEED THE POWER STEERING SYSTEM PROCEED AS FOLLOWS:

1. BEGIN WITH THE ENGINE OFF, FRONT WHEELS OFF THE GROUND, AND WHEELS TURNED ALL THE WAY TO THE LEFT.

2. ADD LOW TEMPERATURE CLIMATE SERVICE FLUID TO THE "FULL COLD" MARK ON THE FLUID LEVEL INDICATOR.

3. BLEED THE SYSTEM BY TURNING THE WHEELS FROM SIDE TO SIDE WITHOUT HITTING STOPS.

IMPORTANT: THIS MAY REQUIRE TURNING THE WHEELS FROM SIDE TO SIDE TWENTY TIMES. ON SYSTEMS WITH LONG RETURN LINES OR FLUID COOLERS, TURNING STEERING WHEEL LOCK-TO-LOCK FORTY TIMES MAY BE REQUIRED. KEEP THE FLUID LEVEL AT THE "FULL COLD" MARK. FLUID WITH AIR IN IT HAS A LIGHT TAN APPEARANCE. THIS AIR MUST BE ELIMINATED FROM THE FLUID BEFORE NORMAL STEERING ACTION CAN BE OBTAINED. 4. START THE ENGINE. WITH THE ENGINE IDLING, RECHECK THE FLUID LEVEL. IF NECESSARY, ADD FLUID TO BRING THE LEVEL TO THE "FULL COLD" MARK.

5. RETURN THE WHEELS TO THE CENTER POSITION. LOWER FRONT WHEELS TO THE GROUND. CONTINUE RUNNING THE ENGINE FOR TWO OR THREE MINUTES.

6. TEST THE VEHICLE TO BE SURE THE STEERING FUNCTIONS NORMALLY AND IS FREE FROM NOISE.

IMPORTANT: INSPECT FOR FLUID LEAKAGE AT CONNECTION POINTS ALONG THE POWER STEERING SYSTEM. 7. RECHECK THE FLUID LEVEL AS DESCRIBED IN STEPS 3 AND 4 EXCEPT THAT THE FLUID LEVEL SHOULD NOW BE UP TO THE "FULL HOT" MARK AFTER THE SYSTEM HAS STABILIZED AT ITS NORMAL OPERATING TEMPERATURE.

FIGURES: 1 ATTACHMENT

Figure 1

GENERAL MOTORS BULLETINS ARE INTENDED FOR USE BY PROFESSIONAL TECHNICIANS, NOT A "DO-IT-YOURSELFER". THEY ARE WRITTEN TO INFORM THOSE TECHNICIANS OF CONDITIONS THAT MAY OCCUR ON SOME VEHICLES, OR TO PROVIDE INFORMATION THAT COULD ASSIST IN THE PROPER SERVICE OF A VEHICLE. PROPERLY TRAINED TECHNICIANS HAVE THE EQUIPMENT, TOOLS, SAFETY INSTRUCTIONS AND KNOW-HOW TO DO A JOB PROPERLY AND SAFELY. IF A CONDITION IS DESCRIBED, DO NOT ASSUME THAT THE BULLETIN APPLIES TO YOUR VEHICLE, OR THAT YOUR VEHICLE WILL HAVE THAT CONDITION.

Hope this may help:

Regards,
VOTIT

Aug 25, 2008 | 1994 Oldsmobile Cutlass Supreme

1 Answer

Cant bleed air out of cooling system


Okay...........best way to actually bleed air out of a Taurus cooling system is to take loose the heater line returning
to the water pump, install a back-flushing tee in the hose, and start the engine while full of antifreeze.
Do this while engine is cool. While engine's warming up,loosen the cap on
the tee and let the air bleed out.KEEP the antifreeze away from the alternator and other components while you do this.
Of course,this will only work if you haven't got a BLOWN HEAD GASKET,letting compression seep into coolant.don-ohio .

Sep 16, 2011 | 2000 Ford Taurus

1 Answer

Power steering pump pushing fluid back out when you cut off engine bleed it 4 times still does it . flushed lines bleed it again still pushing fluid out can you help me


the pump should have a check valve on the presure side causing the fluid to go through the rack to the return line if this is faulty the high presure in the system will push back when engine is turned off.

Mar 08, 2011 | 1999 Ford Taurus

1 Answer

1st thing in the AM the power steering on my 99 silverado pickup does'nt work till you jog the wheel a little then it is fine. Will flushing the system do any good and if so how do tell which is the return...


Sounds like power steering control valve is sticking.Flushing might help.The pressure line is metal and the return is usually rubber at the back of rear of pump.Use power steering fluid not atf to refill pump.

Dec 10, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

POWER STEERING WHINES... WE HAVE ALREADY REPLACED STEERING PUMP (2 TIMES), STEERING RACK AND RETURN LINE.AND FLUSHED SYSTEM OUT AT LEAST 3 TIMES. STILL WHINES (MORESO WHEN COLD) SEEMS BETTER AFTER WARMED...


RAISE FRONT OF CAR MAKE SURE POWER STEERING RESERVIOR IS FULL OF FLUID TURN STEERING WHEEL LOCK TO LOCK (MAX TO MAX) 50 TIMES TO BLEED THE SYSTEM IF THIS DOESN'T WORK THEN IT MEANS THE SYSTEM IS SUCKING AIR SOMEWHERE

Aug 25, 2010 | 2005 Saturn Relay

2 Answers

Where is the power steering dipstick


Most power steering pumps are driven by the serpentine belt and should be in plain view when the hood is open.The following shows how to remove and replace the power steering pump and might give you a clue if not in plain sight. My dad's 1998 Ford Taurus has it nearly on top, but they could have changed things in the mean time: Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Remove the alternator.
  5. Drain and remove the radiator coolant recovery reservoir.
  6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  7. Remove the idler pulley from the power steering pump support.
  8. Remove the belt tensioner.
  9. Remove the bracket mounting bolt located under the belt tensioner mounting.
  10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  11. Clamp the pump support bracket in a suitable vise.
  12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.
To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.
Power steering pump special tools ford-08-00-401.gif

  1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
  4. Install the bracket mounting bolt located under the belt tensioner mounting.
  5. Install the belt tensioner.
  6. Install the idler pulley to the power steering pump support.
  7. Connect the hydraulic pressure and return lines.
  8. Install the radiator coolant recovery reservoir.
  9. Install the alternator.
  10. Install the accessory drive belt.
  11. Fill the power steering reservoir with power steering fluid.
  12. Connect the battery ground cable.
  13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.
Power Steering Pump (4V) and SHO To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Drain and remove the radiator coolant recovery reservoir.
  5. Position a drain pan under the power steering pump. Disconnect the power steering pump reservoir hose and allow it to drain.
  6. Using Pulley Remover T69L-10300-B, or equivalent, remove the pulley from the power steering pump shaft.
  7. Disconnect the pressure hose from the power steering pump and allow it to drain.
  8. Remove the power steering pump retaining bolts and the pump.
To Install:
  1. Install the power steering pump and tighten the bolts 15–22 ft. lbs. (20–30 Nm).
  2. Connect the pressure hose and secure the clamp.
  3. Using a Steering Pump Pulley Replacer T65P-3A733-C, or equivalent, install the power steering pump pulley: the pulley face must be flush with the pump shaft or within 0.010 inch (0.25mm).
  4. Connect the power steering pump reservoir hose.
  5. Install the radiator coolant recovery reservoir.
  6. Install the accessory drive belt.
  7. Fill the power steering reservoir with power steering fluid.
  8. Connect the battery ground cable.
  9. Start the engine and check for leaks and proper operation. Bleed the power steering system if needed.
prev.gif next.gif

Jul 22, 2010 | 1996 Ford Taurus

1 Answer

Wine in power steering, I put in new fan belt, power steering pump, new rack


The wine will be there until the fluid bleeds out all the air.If it does not,then have the power steering pump replaced again,and be sure to flush the system with a good power steering flush.But the remanufatured pump is most likely the problem.The pump had a flaw that the rebuilder didn`t see.Do make sure the lines are not kinked anywhere.

Oct 05, 2009 | 1988 Buick LeSabre

1 Answer

Changing power steering pump


Power steering pump special tools

519a4ae.gif
Power Steering Pump Removal & Installation Power Steering Pump (2V) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the battery ground cable.
  3. Remove the accessory drive belt.
  4. Remove the alternator.
  5. Drain and remove the radiator coolant recovery reservoir.
  6. Position a drain pan under the power steering pump underneath the vehicle. Disconnect the hydraulic pressure and return lines and allow to drain.
  7. Remove the idler pulley from the power steering pump support.
  8. Remove the belt tensioner.
  9. Remove the bracket mounting bolt located under the belt tensioner mounting.
  10. Remove two retaining nuts from the bracket mounting studs. Remove both mounting studs, and pull off the power steering pump support with the pump attached.
  11. Clamp the pump support bracket in a suitable vise.
  12. Remove the power steering pump pulley from the pump shaft using Pump Pulley Remover T69L-10300-B, or equivalent. Remove the three bolts retaining the power steering pump to the power steering pump support and remove the power steering pump.

To Install:
NOTE: The pulley must be installed within 0.010 in (0.25 mm) flush with the power steering pump shaft.

  1. Install the power steering pump to the power steering pump support. Tighten the mounting bolts to 18 ft-lb. (25 Nm).
  2. Install the power steering pump pulley using Steering Pump Pulley Replacer T65P-3A733-C, or equivalent; the pulley face must be flush within 0.010 inch (0.25mm) of the pump shaft.
  3. Install the power steering pump/pump support and torque nuts/bolt to 24 ft. lbs. (33 Nm).
  4. Install the bracket mounting bolt located under the belt tensioner mounting.
  5. Install the belt tensioner.
  6. Install the idler pulley to the power steering pump support.
  7. Connect the hydraulic pressure and return lines.
  8. Install the radiator coolant recovery reservoir.
  9. Install the alternator.
  10. Install the accessory drive belt.
  11. Fill the power steering reservoir with power steering fluid.
  12. Connect the battery ground cable.
  13. Run the engine and check for leaks and proper operation. Bleed the power steering system if needed.

Jun 28, 2009 | 1999 Ford Taurus

Not finding what you are looking for?
1992 Cadillac DeVille Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...