Question about 1996 Jeep Grand Cherokee

Open Question

Repleace the coil and the pick up assembly and now the crank shaft position sensor, still will not start and no spark

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
shanat
  • 359 Answers

SOURCE: 1991 jeep wrangler cranks but wont start

just a suggestion hows your leads?

Posted on May 24, 2008

Ad
c17hydro
  • 2984 Answers

SOURCE: 98 Dodge Dakota "pick up coil" cam position sensor repeat failure

Honestly? Cruddy parts.

I have a Dodge Stratus....97....same thing here. Unfortunately, shoddy parts, even from the dealership. I think the best thing is to keep a fresh one on hand. I know that the wiring is garbage too due to how the harness curls up to the sensor. Not much to tell you on this one.

Posted on Mar 26, 2009

  • 383 Answers

SOURCE: CRANK SHAFT POSITION SENSOR 20002 NISSAN ALTIMA

1st, Nissan had a recall on Crank position sensors for 2002-2006 Altima's. Check with you dealer before you go doing any repairs. You may discover you can get your car repaired at no charge.
NHTSA Campaign ID number :O7V527000
Symptom: Erratic behavior. Stalling and no starts and very difficult to diagnose due to the time frame in which the component actually malfunctions. The warranty should not be limited to the original owner.
I would also need more specifics as to which engine you have so I might assist you in where the location of the sensor is. The Altima had a 4 and a 6 cyl engine offered that year.

Posted on Apr 06, 2009

  • 3 Answers

SOURCE: 1994 Dodge Ram 1500 5.9 (360) won't start new fuel pump, coil??

Maybe check ignition control modual.

Posted on Apr 21, 2009

  • 201 Answers

SOURCE: 1992 dodge 318 engine turns over, but no start. No

if truck has a ceramic ballist resistor near and connected to coil this could be problem or the crk posistion sensor could be too, i would change ballast first if you have on your truck appx cost $10

Posted on May 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999 chevy blazer will not start. No spark!?!? No spark from the coil to ground.


Could be a bad coil, bad Ignition Control Module (what controls the ignition coil as commanded by the engine computer), or a bad crank position sensor, or cam position sensor. Or the wiring and circuits to all the ignition parts.
Often it is the crank sensor (CKP sensor)-The pcm must have this information from the crank sensor to determine spark timing. If no good signal from the crank sensor, there will be no spark.

May 29, 2017 | Cars & Trucks

1 Answer

Hyundai 1.6 Elantra gls, does the spark come from the cylinder head or the crank shaft


neither
the crank shaft position sensor triggers the ignition control module that generates the spark either internally or through a coil/ pack
the cam position sensor ok, s that process to prove that the cam shaft is turning correctly

Apr 13, 2017 | Hyundai Cars & Trucks

2 Answers

Why car my car start?


No spark? Then there is probably no signal to trigger the spark. Possible causes:
1) Cam position sensor.
2) Crank position sensor (you replaced it)
3) Coils (already replaced)
3) Wiring and connections to and from coils (bad grounding points or bad live feeds)

Suggestion: Stop the guessing and spending with "probable" causes. Have the car scannned for error codes and start from scratch according to error codes.

Apr 26, 2014 | Hyundai Motor 2004 Sonata

1 Answer

1994 jeep cherokee laredo no spark after shutting offf at home. Been starting slower and missing the first few minutes before settleing out and runs smoother in the morning. Oil i sold though is the o


No spark can be caused by a bad crank position sensor, or a bad pick-up coil inside the distributor, especially if you can't find a signal to the coil with key on. You could also test the coil, or try a known good one. There is a test procedure for the crank position sensor, but you'd have to locate a repair manual for it. I think it's just running a resistance test across two terminals of the sensor harness connector with an ohmmeter. My son's Jeep had a bad pick-up coil that shut it down, and no spark.
Once you get it running, and if still hard starting, check the fuel pressure.

Dec 09, 2012 | 1994 Jeep Grand Cherokee

1 Answer

95 geo wont start changed ignition module no spark but turns over


The other sensors whereby the computer controls spark timing, are the Crank Position Sensor, and the Cam Position Sensor (sometimes called the pick-up coil, inside the distributor).

Oct 30, 2012 | 1995 Geo Metro

1 Answer

Key turns,gas pump works, does not turn


Try this...

You need to check for spark at the number 1 spark plug if no spark then it could be a few things
1.crank shaft position sensor
2. distributor cap or plugs
3. pick up coil inside distributor
4. ignition coil
5.ignition module
6.Blowen fuse check both engine fuses and inside cab fuses
7. oil pressure switch
You can pull the coil wire going into the distributor cap and check for spark there if no spark there then your problem will be from the ignition coil back

Jun 02, 2010 | 1998 Ford Taurus

2 Answers

No spark no FI pulse NO START


Check the ignition switch please. Had that on a 93 Ford that it was bad and the coil wasnt getting any electricity while the switch was in "start" position.

Aug 17, 2009 | 1994 Ford Escort

1 Answer

No spark, 1988 Toyota Camry 3SFE 4cyl, 5 speed.


there is no crank sensor on this vehicles 2.0L. If you have power to the coil, new coil, cap and rotor try this if not done yet>>>Unplug coil power first....Try pulling off the distributor cap, and make sure the rotor is spinning with the cam...If this fails to spin, inspect the entire distributor assembly. If it passes, Inspect all the power circuit and wiring to the dist assembly, if ok possible ecu. i recommend having a mechanic check it out!! Hopefully this helps...please rate...thanks

Aug 11, 2009 | 1988 Toyota Camry

3 Answers

1992 dodge 318 engine turns over, but no start. No spark present. Replaced ignition coil and pickup coil, still no spark. 1992 dodge ram 150 full size truck 318 engine. starts sometimes then wont start...


if truck has a ceramic ballist resistor near and connected to coil this could be problem or the crk posistion sensor could be too, i would change ballast first if you have on your truck appx cost $10

May 09, 2009 | 1992 Dodge Ram 150 Club Cab

Not finding what you are looking for?
1996 Jeep Grand Cherokee Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...