Question about Mercedes-Benz ML350

Open Question


Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: my 1993 300e radio just

If the radio is not happy with the code you are entering there is a possiblity it has locked you out - Leaving the ignition on with WAIT on the screen (1 minute for 1st incorrect enter, 2min for 2nd, 4min for 3rd, 8min for 4th etc) until such time that the radio displays CODE or until leaving the ignition on doesn't remove WAIT from the screen. (possible new radio required at that point)

Posted on Feb 19, 2011

  • 2 Answers

SOURCE: Resetting Radio with WAIT on an 01' Ml 320

you must remove the power going to the radio for 5 mins, you can do this by removing the fuse in the fuse panel for 5 mins, put fuse back in, then enter code - if that doesn't work then you have to remove the negative battery cable for 5 mins, then reconnect neg cable back to battery, then enter code - the key to it is removing power to the radio - the last resort is to remove radio from the dash and unpluging the elec connector from back of radio for 5 mins - the factory "code" should be on a sticker stuck to the radio, you should be able to find it when you remove the radio from the dash.

Posted on Mar 01, 2009

  • 1 Answer

SOURCE: Resetting Radio with WAIT on an 01' Ml 320

I've entered incorrect radio code and it is now stuck on WAIT. but i don`t have the code what can i do. pl. help me

Posted on Apr 03, 2009

  • 1 Answer

SOURCE: 1993 BMW 525i.The radio displays code after

What was the code my radio says it needs the code

Posted on Aug 31, 2010

  • 166 Answers

SOURCE: After changing my ML350 battery the SRS light is

you can try disconnecting the battery again and see if the light goes away but usually when a srs light comes on the only way to clear it is with the 'sds' which the dealer has and sometimes the independent shops might have one too. Mercedes doesn't allow you to reset it from the vehicle due to it being safety related. when the srs light is on all your airbags and seatbelt etr's are disabled. if your vehicle has pre-safe then you will have to just drive it around til it relearns the steering angle sensor again. if that's the case it will say see owners manual in the display of the instrument cluster when showing the fault.

Posted on Sep 30, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I reset my security code for my 2005 ML350.

If you're talking the code you set it to then instructions for changing it should be in the instruction manual. Which can be downloaded off the internet. If you're talking about the factory set code, if your disconnect the battery and let set for a few minutes then it will reset to factory code. After the factory code reset you should be able to easily reset your own created security code.

Feb 09, 2018 | Cars & Trucks

1 Answer


call the dealer. there mite be a reset procces. when i worked at sears we had to call the dealer on problems like this.

Jan 31, 2013 | 1995 Jeep Grand Cherokee

1 Answer

This morning when I attempted to start my 2006 Hummer H3, nothing happened. I thought I may have a dead battery but the lights and radio work fine. I then noticed the Passlock security lock light was on...

Hello:Try this procedure: turn key on, turn to start, let key come back to on wait ten minutes, turn key off wait 10 seconds turn key back on wait 10 minutes. turn key off wait 10 seconds turn key back on wait 10 minutes turn key off wait 10 seconds NOW try and start. In addition you might try tapping on switch assembly while trying to start. There is not any way to disable passlock. You might try having the engine control system codes read

Feb 01, 2011 | 2006 Hummer H3

2 Answers

2005 Hardbody. Radio display "Code Err" How do I

You have to leave your radio on for 60 minutes and then it resets to "code in"
It works I tried it today

Jan 07, 2011 | 1990 Nissan Hardbody King Cab

1 Answer

I changed the battery and my radio reseted when i wrote the code the radio kept saying wait who can i fix this.....

your radio is in safe or anti theft mode. Radio security codes are normally wrote down down in your owners manual when vehicle was purchased new, otherwise you will need to contact the dealer with your vin to get your specific code to unlock it. hope this helps and happy holidays

Dec 24, 2010 | 2005 Chrysler Town & Country

2 Answers

2006 honda accord, after changing the battery. resetting the radio code. the radio will not pick up any stations???

Unless the Accord was jump started, creating possible power surge to damage radio, it should not of had any relationship to the radio.

But, just in case, would suggest disconnecting battery for 5 minutes, reconnecting battery, reentering radio code and see what happens.

If that fails, hopefully your under 36k miles or got the Factory extended warranty "Honda Care" Service plan, so take to the Honda Dealership to see what they say.

Mar 10, 2009 | 2006 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

293 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

79024 Answers

Joseph Prosser

Level 3 Expert

772 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides